NASLite Network Attached Storage • View topic

View unanswered posts | View active topics

Board index » v2.x NASLite Products » NASLite-2

All times are UTC - 5 hours [ DST ]

Chipset IT8212

Page 1 of 1

[ 9 posts ]

Previous topic | Next topic

Author

Message

Bassi6

Post subject: Chipset IT8212

Posted: Thu Jan 04, 2007 12:03 pm

Joined: Tue Apr 18, 2006 2:02 pm
Posts: 4

I have just setup naslite 2.03 on a Gigabite GA-8KNXP motherboard and everything vent fine except for the onboard ata raid (IT8212 chipset) I cant see any disks. I tryed all possibilities in the raid bios so I guess the chip set is not supported. This is what I see and Disk-6 is properly the raid

0 - Disk-0, IDE-0-0-0-0
1 - Disk-1, IDE-0-0-1-0
2 - Disk-2, IDE-0-1-0-0
3 - Disk-3, IDE-0-1-1-0
4 - Disk-4, IDE-2-0-0-0
5 - Disk-5, IDE-2-0-1-0
* - Disk-6, SCSI-3-0-0-0

G - General Storage Option Menu

R - Return To Main Option Menu

Am I right or not??? and will the chip set be supported in upcoming releases
My upgrade time is over but I am willing to buy it again if it will be supported

Bjarni

Top

liuqyn

Post subject:

Posted: Thu Jan 04, 2007 7:27 pm

Joined: Mon Jul 24, 2006 7:39 pm
Posts: 16

to the best of my knowledge, all onboard raids are software/driver raid not hardware. are you trying to setit up as raid or just using for extra single drives? and that disc 6 may be you config drive, it's always listed last.

Top

Neil.

Post subject:

Posted: Fri Jan 05, 2007 5:39 am

Joined: Sat Dec 30, 2006 5:41 am
Posts: 7

Disk 6 is your config drive. I did not think the ITE8212 was compatible with Naslite. I have a PCI version, when I set up 2 drives as RAID 1 (it is hardware RAID) it did not see them at all.

Top

Bassi6

Post subject:

Posted: Fri Jan 05, 2007 5:51 am

Joined: Tue Apr 18, 2006 2:02 pm
Posts: 4

Thanks I had figured out that Drive-6 is the config drive so I can just hope there will be support in upcoming realeases

Top

gaiden

Post subject:

Posted: Fri Jan 05, 2007 11:27 am

Joined: Sun Jul 09, 2006 10:26 am
Posts: 428
Location: UK

Did you enable RW in the storage options for each drive?

I have a Kt7a Raid MB and can use the extra channels.

Top

Bassi6

Post subject:

Posted: Fri Jan 05, 2007 12:20 pm

Joined: Tue Apr 18, 2006 2:02 pm
Posts: 4

I cant see the drives connected to the controller

Top

gaiden

Post subject:

Posted: Fri Jan 05, 2007 2:32 pm

Joined: Sun Jul 09, 2006 10:26 am
Posts: 428
Location: UK

what happens when you select one of the drives, can u select 0 in the storage options

0 - Disk-0, IDE-0-0-0-0
1 - Disk-1, IDE-0-0-1-0
2 - Disk-2, IDE-0-1-0-0
3 - Disk-3, IDE-0-1-1-0
4 - Disk-4, IDE-2-0-0-0
5 - Disk-5, IDE-2-0-1-0

Top

Bassi6

Post subject:

Posted: Fri Jan 05, 2007 8:30 pm

Joined: Tue Apr 18, 2006 2:02 pm
Posts: 4

I can configure all drives I can see and today I did put in a pci ide card some noname card and now I can see all drives

0 - Disk-0, IDE-0-0-0-0
1 - Disk-1, IDE-0-0-1-0
* - Disk-10, SCSI-3-0-0-0
2 - Disk-2, IDE-0-1-0-0
3 - Disk-3, IDE-0-1-1-0
4 - Disk-4, IDE-2-0-0-0
5 - Disk-5, IDE-2-0-1-0
6 - Disk-6, IDE-4-0-0-0
7 - Disk-7, IDE-4-0-1-0
8 - Disk-8, IDE-4-1-0-0
9 - Disk-9, IDE-4-1-1-0

guess I have to wait until my chipset is supported if ever

Top

fordem

Post subject:

Posted: Sat Jan 06, 2007 7:04 pm

Joined: Mon Jan 23, 2006 11:22 am
Posts: 144

liuqyn wrote:

Far from correct - many of the older Dell servers ship with what Dell calls ROMB - Raid On Mother Board - which is usually but not always based on an Adaptec RAID implementation and is true hardware RAID

Top

Page 1 of 1

[ 9 posts ]

Board index » v2.x NASLite Products » NASLite-2

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 8 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum