NASLite Network Attached Storage

www.serverelements.com
Task-specific simplicity with low hardware requirements.
It is currently Thu Dec 05, 2019 8:26 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 55 posts ]  Go to page Previous  1, 2, 3, 4  Next
Author Message
PostPosted: Tue Nov 04, 2008 4:40 pm 
Offline

Joined: Tue Oct 28, 2008 12:20 pm
Posts: 45
This should help out someone. This is my syslog. I do see that it says something about megaraid but I dont understand it.

System Message Log:

* Nov 4 18:30:57 user.notice kernel: klogd started: BusyBox v1.01 (2007.03.15-22:03+0000)
* Nov 4 18:30:57 user.warn kernel: Linux version 2.4.35.NASLite (root@tzt) (gcc version 3.4.6) #2 Sun Aug 12 09:03:16 EDT 2007
* Nov 4 18:30:57 user.info kernel: BIOS-provided physical RAM map:
* Nov 4 18:30:57 user.warn kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
* Nov 4 18:30:57 user.warn kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
* Nov 4 18:30:57 user.warn kernel: BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
* Nov 4 18:30:57 user.warn kernel: BIOS-e820: 0000000000100000 - 000000000fec0000 (usable)
* Nov 4 18:30:57 user.warn kernel: BIOS-e820: 000000000fec0000 - 000000000fef8000 (ACPI data)
* Nov 4 18:30:57 user.warn kernel: BIOS-e820: 000000000fef8000 - 000000000ff00000 (ACPI NVS)
* Nov 4 18:30:57 user.warn kernel: BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
* Nov 4 18:30:57 user.warn kernel: BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
* Nov 4 18:30:57 user.notice kernel: 0MB HIGHMEM available.
* Nov 4 18:30:57 user.notice kernel: 254MB LOWMEM available.
* Nov 4 18:30:57 user.warn kernel: On node 0 totalpages: 65216
* Nov 4 18:30:57 user.warn kernel: zone(0): 4096 pages.
* Nov 4 18:30:57 user.warn kernel: zone(1): 61120 pages.
* Nov 4 18:30:57 user.warn kernel: zone(2): 0 pages.
* Nov 4 18:30:57 user.notice kernel: ACPI disabled because your bios is from 2000 and too old
* Nov 4 18:30:57 user.notice kernel: You can enable it with acpi=force
* Nov 4 18:30:57 user.warn kernel: Kernel command line: rw root=/dev/ram0 initrd=NASLite.02 quiet BOOT_IMAGE=NASLite.01
* Nov 4 18:30:57 user.info kernel: Initializing CPU#0
* Nov 4 18:30:57 user.warn kernel: Detected 797.355 MHz processor.
* Nov 4 18:30:57 user.warn kernel: Console: colour VGA+ 80x25
* Nov 4 18:30:57 user.warn kernel: Calibrating delay loop. 1592.52 BogoMIPS
* Nov 4 18:30:57 user.info kernel: Memory: 251792k/260864k available (2214k kernel code, 8684k reserved, 642k data, 540k init, 0k highmem)
* Nov 4 18:30:57 user.info kernel: Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
* Nov 4 18:30:57 user.info kernel: Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
* Nov 4 18:30:57 user.info kernel: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
* Nov 4 18:30:57 user.info kernel: Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
* Nov 4 18:30:57 user.warn kernel: Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
* Nov 4 18:30:57 user.info kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
* Nov 4 18:30:57 user.info kernel: CPU: L2 cache: 256K
* Nov 4 18:30:57 user.debug kernel: CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
* Nov 4 18:30:57 user.debug kernel: CPU: Common caps: 0383f9ff 00000000 00000000 00000000
* Nov 4 18:30:57 user.warn kernel: CPU: Intel Pentium III (Coppermine) stepping 06
* Nov 4 18:30:57 user.info kernel: Enabling fast FPU save and restore. done.
* Nov 4 18:30:57 user.info kernel: Enabling unmasked SIMD FPU exception support. done.
* Nov 4 18:30:57 user.info kernel: Checking 'hlt' instruction. OK.
* Nov 4 18:30:57 user.warn kernel: POSIX conformance testing by UNIFIX
* Nov 4 18:30:57 user.warn kernel: mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
* Nov 4 18:30:57 user.warn kernel: mtrr: detected mtrr type: Intel
* Nov 4 18:30:57 user.info kernel: ACPI: Subsystem revision 20040326
* Nov 4 18:30:57 user.info kernel: ACPI: Interpreter disabled.
* Nov 4 18:30:57 user.info kernel: PCI: PCI BIOS revision 2.10 entry at 0xfda95, last bus=1
* Nov 4 18:30:57 user.info kernel: PCI: Using configuration type 1
* Nov 4 18:30:57 user.info kernel: PCI: Probing PCI hardware
* Nov 4 18:30:57 user.warn kernel: PCI: Probing PCI hardware (bus 00)
* Nov 4 18:30:57 user.warn kernel: Transparent bridge - PCI device 8086:244e
* Nov 4 18:30:57 user.info kernel: PCI: Using IRQ router PIIX/ICH [8086/2440] at 00:1f.0
* Nov 4 18:30:57 user.info kernel: Linux NET4.0 for Linux 2.4
* Nov 4 18:30:57 user.info kernel: Based upon Swansea University Computer Society NET3.039
* Nov 4 18:30:57 user.warn kernel: Initializing RT netlink socket
* Nov 4 18:30:57 user.warn kernel: Starting kswapd
* Nov 4 18:30:57 user.info kernel: Journalled Block Device driver loaded
* Nov 4 18:30:57 user.info kernel: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
* Nov 4 18:30:57 user.info kernel: devfs: boot_options: 0x1
* Nov 4 18:30:57 user.info kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
* Nov 4 18:30:57 user.warn kernel: pty: 256 Unix98 ptys configured
* Nov 4 18:30:57 user.info kernel: Real Time Clock Driver v1.10f
* Nov 4 18:30:57 user.info kernel: Floppy drive(s): fd0 is 1.44M
* Nov 4 18:30:57 user.info kernel: FDC 0 is a post-1991 82077
* Nov 4 18:30:57 user.warn kernel: RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
* Nov 4 18:30:57 user.info kernel: loop: loaded (max 8 devices)
* Nov 4 18:30:57 user.info kernel: Intel(R) PRO/1000 Network Driver - version 7.3.20-k4
* Nov 4 18:30:57 user.info kernel: Copyright (c) 1999-2006 Intel Corporation.
* Nov 4 18:30:57 user.info kernel: dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15
* Nov 4 18:30:57 user.warn kernel: FW Version=$Version$
* Nov 4 18:30:57 user.info kernel: PCI: Found IRQ 11 for device 01:0d.0
* Nov 4 18:30:57 user.info kernel: PCI: Sharing IRQ 11 with 01:09.0
* Nov 4 18:30:57 user.warn kernel: 3c59x: Donald Becker and others. http://www.scyld.com/network/vortex.html
* Nov 4 18:30:57 user.info kernel: 01:0d.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xdc00. Vers LK1.1.18
* Nov 4 18:30:57 user.info kernel: pcnet32.c:v1.30h 06.24.2004 tsbogend@alpha.franken.de
* Nov 4 18:30:57 user.info kernel: ThunderLAN driver v1.15
* Nov 4 18:30:57 user.info kernel: TLAN: 0 devices installed, PCI: 0 EISA: 0
* Nov 4 18:30:57 user.info kernel: dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
* Nov 4 18:30:57 user.info kernel: ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
* Nov 4 18:30:57 user.notice kernel: Intel(R) PRO/100 Network Driver - version 2.3.43-k1
* Nov 4 18:30:57 user.notice kernel: Copyright (c) 2004 Intel Corporation
* Nov 4 18:30:57 user.notice kernel:
* Nov 4 18:30:57 user.info kernel: PCI: Found IRQ 11 for device 01:09.0
* Nov 4 18:30:57 user.info kernel: PCI: Sharing IRQ 11 with 01:0d.0
* Nov 4 18:30:57 user.debug kernel: e100: selftest OK.
* Nov 4 18:30:57 user.notice kernel: e100: eth1: Intel(R) PRO/100 Network Connection
* Nov 4 18:30:57 user.notice kernel: Hardware receive checksums enabled
* Nov 4 18:30:57 user.notice kernel: cpu cycle saver enabled
* Nov 4 18:30:57 user.notice kernel:
* Nov 4 18:30:57 user.warn kernel: sk98lin: No adapter found.
* Nov 4 18:30:57 user.info kernel: forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.50.
* Nov 4 18:30:57 user.info kernel: lti-Platform E-IDE driver Revision: 7.00beta4-2.4
* Nov 4 18:30:57 user.info kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
* Nov 4 18:30:57 user.info kernel: ICH2: IDE controller at PCI slot 00:1f.1
* Nov 4 18:30:57 user.info kernel: ICH2: chipset revision 1
* Nov 4 18:30:57 user.info kernel: ICH2: not 100% native mode: will probe irqs later
* Nov 4 18:30:57 user.info kernel: ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
* Nov 4 18:30:57 user.info kernel: ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
* Nov 4 18:30:57 user.warn kernel: hda: WDC WD5000AAKB-00YSA0, ATA DISK drive
* Nov 4 18:30:57 user.warn kernel: hdb: WDC WD5000AAKB-00UKA0, ATA DISK drive
* Nov 4 18:30:57 user.warn kernel: hdc: LITE-ON CD-ROM LTN-5291S, ATAPI CD/DVD-ROM drive
* Nov 4 18:30:57 user.warn kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
* Nov 4 18:30:57 user.warn kernel: ide1 at 0x170-0x177,0x376 on irq 15
* Nov 4 18:30:57 user.warn kernel: hda: attached ide-disk driver.
* Nov 4 18:30:57 user.warn kernel: hda: host protected area => 1
* Nov 4 18:30:57 user.info kernel: hda: 976773168 sectors (500108 MB) w/16384KiB Cache, CHS=60801/255/63, UDMA(100)
* Nov 4 18:30:57 user.warn kernel: hdb: attached ide-disk driver.
* Nov 4 18:30:57 user.warn kernel: hdb: host protected area => 1
* Nov 4 18:30:57 user.info kernel: hdb: 976773168 sectors (500108 MB) w/16384KiB Cache, CHS=60801/255/63, UDMA(100)
* Nov 4 18:30:57 user.info kernel: Partition check:
* Nov 4 18:30:57 user.info kernel: /dev/ide/host0/bus0/target0/lun0: p1
* Nov 4 18:30:57 user.info kernel: /dev/ide/host0/bus0/target1/lun0: p1
* Nov 4 18:30:57 user.info kernel: SCSI subsystem driver Revision: 1.00
* Nov 4 18:30:57 user.info kernel: Loading Adaptec I2O RAID: Version 2.4 Build 5
* Nov 4 18:30:57 user.info kernel: Detecting Adaptec I2O RAID controllers.
* Nov 4 18:30:57 user.info kernel: Red Hat/Adaptec aacraid driver (1.1-3 Aug 12 2007 09:05:44)
* Nov 4 18:30:57 user.warn kernel: scsi: Detection failed (no card)
* Nov 4 18:30:57 user.notice kernel: megaraid: v2.10.10.1 (Release Date: Thu Jan 27 16:19:44 EDT 2005)
* Nov 4 18:30:57 user.info kernel: PCI: Found IRQ 9 for device 01:0a.0
* Nov 4 18:30:57 user.notice kernel: megaraid: found 0x101e:0x1960:bus 1:slot 10:func 0
* Nov 4 18:30:57 user.notice kernel: scsi1:Found MegaRAID controller at 0xd0804000, IRQ:9
* Nov 4 18:30:57 user.notice kernel: megaraid: [6.62:1.03] detected 1 logical drives.
* Nov 4 18:30:57 user.notice kernel: megaraid: supports extended CDBs.
* Nov 4 18:30:57 user.info kernel: megaraid: channel[0] is raid.
* Nov 4 18:30:57 user.info kernel: megaraid: channel[1] is raid.
* Nov 4 18:30:57 user.info kernel: megaraid: channel[2] is raid.
* Nov 4 18:30:57 user.info kernel: megaraid: channel[3] is raid.
* Nov 4 18:30:57 user.info kernel: scsi1 : LSI Logic MegaRAID 6.62 254 commands 16 targs 7 chans 7 luns
* Nov 4 18:30:57 user.notice kernel: scsi1: scanning scsi channel 0 for logical drives.
* Nov 4 18:30:57 user.notice kernel: scsi1: scanning scsi channel 1 for logical drives.
* Nov 4 18:30:57 user.notice kernel: scsi1: scanning scsi channel 2 for logical drives.
* Nov 4 18:30:57 user.notice kernel: scsi1: scanning scsi channel 3 for logical drives.
* Nov 4 18:30:57 user.notice kernel: scsi1: scanning scsi channel 4 [P0] for physical devices.
* Nov 4 18:30:57 user.notice kernel: scsi1: scanning scsi channel 5 [P1] for physical devices.
* Nov 4 18:30:57 user.notice kernel: scsi1: scanning scsi channel 6 [P2] for physical devices.
* Nov 4 18:30:57 user.notice kernel: scsi1: scanning scsi channel 7 [P3] for physical devices.
* Nov 4 18:30:57 user.warn kernel: GDT-HA: Storage RAID Controller Driver. Version: 3.04
* Nov 4 18:30:57 user.warn kernel: GDT-HA: Found 0 PCI Storage RAID Controllers
* Nov 4 18:30:57 user.warn kernel: 3ware Storage Controller device driver for Linux v1.02.00.037.
* Nov 4 18:30:57 user.warn kernel: 3w-xxxx: No cards found.
* Nov 4 18:30:57 user.debug kernel: libata version 1.20 loaded.
* Nov 4 18:30:57 user.info kernel: raw1394: /dev/raw1394 device initialized
* Nov 4 18:30:57 user.info kernel: sbp2: $Rev: 1074 $ Ben Collins
* Nov 4 18:30:57 user.err kernel: ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
* Nov 4 18:30:57 user.info kernel: usb.c: registered new driver usbdevfs
* Nov 4 18:30:57 user.info kernel: usb.c: registered new driver hub
* Nov 4 18:30:57 user.info kernel: host/uhci.c: USB Universal Host Controller Interface driver v1.1
* Nov 4 18:30:57 user.info kernel: PCI: Found IRQ 11 for device 00:1f.2
* Nov 4 18:30:57 user.debug kernel: PCI: Setting latency timer of device 00:1f.2 to 64
* Nov 4 18:30:57 user.info kernel: host/uhci.c: USB UHCI at I/O 0xef40, IRQ 11
* Nov 4 18:30:57 user.info kernel: usb.c: new USB bus registered, assigned bus number 1
* Nov 4 18:30:57 user.info kernel: hub.c: USB hub found
* Nov 4 18:30:57 user.info kernel: hub.c: 2 ports detected
* Nov 4 18:30:57 user.info kernel: PCI: Found IRQ 10 for device 00:1f.4
* Nov 4 18:30:57 user.debug kernel: PCI: Setting latency timer of device 00:1f.4 to 64
* Nov 4 18:30:57 user.info kernel: host/uhci.c: USB UHCI at I/O 0xef80, IRQ 10
* Nov 4 18:30:57 user.info kernel: usb.c: new USB bus registered, assigned bus number 2
* Nov 4 18:30:57 user.info kernel: hub.c: USB hub found
* Nov 4 18:30:57 user.info kernel: hub.c: 2 ports detected
* Nov 4 18:30:57 user.info kernel: usb.c: registered new driver usbkbd
* Nov 4 18:30:57 user.info kernel: usbkbd.c: :USB HID Boot Protocol keyboard driver
* Nov 4 18:30:57 user.info kernel: Initializing USB Mass Storage driver.
* Nov 4 18:30:57 user.info kernel: usb.c: registered new driver usb-storage
* Nov 4 18:30:57 user.info kernel: USB Mass Storage support registered.
* Nov 4 18:30:57 user.info kernel: NET4: Linux TCP/IP 1.0 for NET4.0
* Nov 4 18:30:57 user.info kernel: IP Protocols: ICMP, UDP, TCP
* Nov 4 18:30:57 user.info kernel: IP: routing cache hash table of 2048 buckets, 16Kbytes
* Nov 4 18:30:57 user.info kernel: TCP: Hash tables configured (established 16384 bind 32768)
* Nov 4 18:30:57 user.info kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
* Nov 4 18:30:57 user.notice kernel: RAMDISK: NASLite file system found at block 0
* Nov 4 18:30:57 user.warn kernel: .<6>Freeing initrd memory: 1952k freed
* Nov 4 18:30:57 user.warn kernel: EXT2-fs warning: checktime reached, running e2fsck is recommended
* Nov 4 18:30:57 user.warn kernel: VFS: Mounted root (ext2 filesystem).
* Nov 4 18:30:57 user.info kernel: Mounted devfs on /dev
* Nov 4 18:30:57 user.info kernel: Freeing unused kernel memory: 540k freed
* Nov 4 18:30:57 user.err kernel: e100: eth1 NIC Link is Up 100 Mbps Full duplex
* Nov 4 18:30:57 user.err kernel: ext3: No journal on filesystem on ide0(3,1)
* Nov 4 18:30:57 user.err kernel: ext3: No journal on filesystem on ide0(3,65)


Top
 Profile  
 
PostPosted: Tue Nov 04, 2008 5:20 pm 
Offline

Joined: Tue Oct 28, 2008 12:20 pm
Posts: 45
I am getting extremely frustrated with this Thing now. I did a reboot and it does show that it is stopping the megaraid card. Why cant i see the drives that are on this card?? I just want to get an example going to show my boss.


Top
 Profile  
 
PostPosted: Tue Nov 04, 2008 5:59 pm 
Offline

Joined: Fri Jan 12, 2007 4:27 am
Posts: 577
Location: Scotland
Have you entered the Licence and Unlock details?


Top
 Profile  
 
PostPosted: Tue Nov 04, 2008 6:02 pm 
Offline

Joined: Tue Oct 28, 2008 12:20 pm
Posts: 45
Yah I have been using the server for almost a year now. and we have all the license and unlock code entered and its legal. It just doesnt detect a drive for the logical drive I set up on the Raid card.


Top
 Profile  
 
PostPosted: Tue Nov 04, 2008 6:04 pm 
Offline

Joined: Tue Oct 28, 2008 12:20 pm
Posts: 45
if you would like any information from my server and I can get some screenshots or something of any of my settings.


Top
 Profile  
 
PostPosted: Tue Nov 04, 2008 6:44 pm 
Offline

Joined: Fri Jan 12, 2007 4:27 am
Posts: 577
Location: Scotland
Your log seems to show that you have 2 drives installed - have you formatted / exported the RAID logical drive?


Top
 Profile  
 
PostPosted: Tue Nov 04, 2008 7:03 pm 
Offline

Joined: Tue Oct 28, 2008 12:20 pm
Posts: 45
thats my problem nowhere in naslite is there an option to format or export the new drives.


Top
 Profile  
 
PostPosted: Tue Nov 04, 2008 7:08 pm 
Offline

Joined: Fri Jan 12, 2007 4:27 am
Posts: 577
Location: Scotland
If you can get into the BIOS on the other PC, why not try to configure the whole server there?

If you can and you can access the drive then if it doesn't work in the first PC then that PC is at fault (in some way - not all motherboards are compatible - or it could just be a BIOS setting or two causing problems). As a matter of course, disable in BIOS *ALL* motherboard devices not used (i.e.USB, LPT, COM, Audio, etc, etc).


Top
 Profile  
 
PostPosted: Tue Nov 04, 2008 7:11 pm 
Offline

Joined: Tue Oct 28, 2008 12:20 pm
Posts: 45
the two drives that you are seeing are probably my original drives which are 500gb. With the raid card I am testing it with 2 10gb drives but it will not let me export them. here is what I have.

I should have 3 drives total. 2 of them are working right now and are not on the raid card.

the other drive is a raid 0 with the 2 10gb drives on the raid card and dont show up in naslite at all.


Attachments:
only 2 drives.jpg
only 2 drives.jpg [ 29.95 KiB | Viewed 17223 times ]
Top
 Profile  
 
PostPosted: Tue Nov 04, 2008 7:13 pm 
Offline

Joined: Tue Oct 28, 2008 12:20 pm
Posts: 45
I will give that a try tomorrow I give up for the day and am now heading home. thanks very much for your help it is much appreciated.


Top
 Profile  
 
PostPosted: Tue Nov 04, 2008 7:17 pm 
Offline

Joined: Fri Jan 12, 2007 4:27 am
Posts: 577
Location: Scotland
Are the drives "exported" on the RAID card? I can't remember off the top of my head how I got the drives which were connected to the LSI card to be seen by NASLite.


Top
 Profile  
 
PostPosted: Tue Nov 04, 2008 8:54 pm 
Offline

Joined: Sun Apr 02, 2006 9:05 pm
Posts: 1681
Location: Up State NY in the USA!!!!
Generally the card is windows centric and as such there is a windows utility you use to access the card and configure the array/s and drives. I have tried to get into the BIOS based utility with no luck, that was my solution. I slaved the card in a windows machine and configured the array, then shut it all down and installed it in the NAS and formated the array EXT3. I know this is sort of a kludge but it works.

Mike


Top
 Profile  
 
PostPosted: Wed Nov 05, 2008 4:55 am 
Offline

Joined: Fri Jan 12, 2007 4:27 am
Posts: 577
Location: Scotland
I did all of my setup in the card's BIOS - I'll try to dig out the card and a pair of IDE drives to see if I can remember how to create a RAID1 array.


Top
 Profile  
 
PostPosted: Wed Nov 05, 2008 10:01 am 
Offline

Joined: Sun Apr 02, 2006 9:05 pm
Posts: 1681
Location: Up State NY in the USA!!!!
The card has to be setup in it's BIOS for the RAID array you wish to have presented to the OS in order to be able to have NASLite see and format it. I just was never able to get into the BIOS to make these changes and set up the card regardless of the firmware revision so I went the windows utility route instead.

The card does work like gang busters once it is configured though so don't give up on it.

Mike


Top
 Profile  
 
PostPosted: Wed Nov 05, 2008 10:20 am 
Offline

Joined: Tue Oct 28, 2008 12:20 pm
Posts: 45
So your saying that if I put the card and drives in a windows pc and get it formatted with the raid utility then I can remove it and put it in the Naslite and it should recognize it?? what is the utility called??


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 55 posts ]  Go to page Previous  1, 2, 3, 4  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group