Server Message Log

This page provides a viewable copy of the current system message log. The system message log contains valuable information that can help in troubleshooting as well as aid in general system administration and maintenance.

System Message Log:

Jan 7 09:40:27 [3] klogd started: BusyBox v1.01 (2008.07.26-02:54+0000) Jan 7 09:40:27 [4] Linux version 2.4.36.NASLite (root@tzt) (gcc version 3.4.6) #2 Wed Jul 16 21:48:01 EDT 2008 Jan 7 09:40:27 [2] BIOS-provided physical RAM map: Jan 7 09:40:27 [4] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) Jan 7 09:40:27 [4] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) Jan 7 09:40:27 [4] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) Jan 7 09:40:27 [4] BIOS-e820: 0000000000100000 - 0000000020000000 (usable) Jan 7 09:40:27 [4] BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved) Jan 7 09:40:27 [4] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) Jan 7 09:40:27 [4] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) Jan 7 09:40:27 [3] 0MB HIGHMEM available. Jan 7 09:40:27 [3] 512MB LOWMEM available. Jan 7 09:40:27 [4] found SMP MP-table at 000ff780 Jan 7 09:40:27 [4] hm, page 000ff000 reserved twice. Jan 7 09:40:27 [4] hm, page 00100000 reserved twice. Jan 7 09:40:27 [4] hm, page 000f0000 reserved twice. Jan 7 09:40:27 [4] hm, page 000f1000 reserved twice. Jan 7 09:40:27 [4] On node 0 totalpages: 131072 Jan 7 09:40:27 [4] zone(0): 4096 pages. Jan 7 09:40:27 [4] zone(1): 126976 pages. Jan 7 09:40:27 [4] zone(2): 0 pages. Jan 7 09:40:27 [5] ACPI: Unable to locate RSDP Jan 7 09:40:27 [4] Intel MultiProcessor Specification v1.4 Jan 7 09:40:27 [4] Virtual Wire compatibility mode. Jan 7 09:40:27 [4] OEM ID: AMI Product ID: CNB30LE APIC at: 0xFEE00000 Jan 7 09:40:27 [4] Processor #0 Pentium(tm) Pro APIC version 17 Jan 7 09:40:27 [4] I/O APIC #4 Version 17 at 0xFEC00000. Jan 7 09:40:27 [4] I/O APIC #5 Version 17 at 0xFEC01000. Jan 7 09:40:27 [4] Enabling APIC mode: Flat.^IUsing 2 I/O APICs Jan 7 09:40:27 [4] Processors: 1 Jan 7 09:40:27 [4] Kernel command line: rw root=/dev/ram0 initrd=NASLite.02 quiet BOOT_IMAGE=NASLite.01 Jan 7 09:40:27 [2] Initializing CPU#0 Jan 7 09:40:27 [4] Detected 797.497 MHz processor. Jan 7 09:40:27 [4] Console: colour VGA+ 80x25 Jan 7 09:40:27 [4] Calibrating delay loop. 1592.52 BogoMIPS Jan 7 09:40:27 [2] Memory: 509888k/524288k available (2325k kernel code, 14012k reserved, 680k data, 556k init, 0k highmem) Jan 7 09:40:27 [2] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Jan 7 09:40:27 [2] Inode cache hash table entries: 32768 (order: 6, 262144 bytes) Jan 7 09:40:27 [2] Mount cache hash table entries: 512 (order: 0, 4096 bytes) Jan 7 09:40:27 [2] Buffer cache hash table entries: 32768 (order: 5, 131072 bytes) Jan 7 09:40:27 [4] Page-cache hash table entries: 131072 (order: 7, 524288 bytes) Jan 7 09:40:27 [2] CPU: L1 I cache: 16K, L1 D cache: 16K Jan 7 09:40:27 [2] CPU: L2 cache: 256K Jan 7 09:40:27 [3] CPU serial number disabled. Jan 7 09:40:27 [2] Intel machine check architecture supported. Jan 7 09:40:27 [2] Intel machine check reporting enabled on CPU#0. Jan 7 09:40:27 [1] CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 Jan 7 09:40:27 [1] CPU: Common caps: 0383fbff 00000000 00000000 00000000 Jan 7 09:40:27 [4] CPU: Intel Pentium III (Coppermine) stepping 06 Jan 7 09:40:27 [2] Enabling fast FPU save and restore. done. Jan 7 09:40:27 [2] Enabling unmasked SIMD FPU exception support. done. Jan 7 09:40:27 [2] Checking 'hlt' instruction. OK. Jan 7 09:40:27 [4] POSIX conformance testing by UNIFIX Jan 7 09:40:27 [4] enabled ExtINT on CPU#0 Jan 7 09:40:27 [4] ESR value before enabling vector: 00000004 Jan 7 09:40:27 [4] ESR value after enabling vector: 00000000 Jan 7 09:40:27 [4] ENABLING IO-APIC IRQs Jan 7 09:40:27 [4] Setting 4 in the phys_id_present_map Jan 7 09:40:27 [2] .changing IO-APIC physical APIC ID to 4 . ok. Jan 7 09:40:27 [4] Setting 5 in the phys_id_present_map Jan 7 09:40:27 [2] .changing IO-APIC physical APIC ID to 5 . ok. Jan 7 09:40:27 [1] init IO_APIC IRQs Jan 7 09:40:27 [1] IO-APIC (apicid-pin) 4-0, 4-9, 4-10, 4-11, 5-0, 5-1, 5-2, 5-3, 5-4, 5-5, 5-8, 5-9, 5-10, 5-12, 5-13, 5-14, 5-15 not connected. Jan 7 09:40:27 [2] TIMER: vector=0x31 pin1=2 pin2=0 Jan 7 09:40:27 [5] MP-BIOS bug: 8254 timer not connected to IO-APIC Jan 7 09:40:27 [2] .trying to set up timer (IRQ0) through the 8259A . Jan 7 09:40:27 [4] . (found pin 0) .works. Jan 7 09:40:27 [1] number of MP IRQ sources: 16. Jan 7 09:40:27 [1] number of IO-APIC #4 registers: 16. Jan 7 09:40:27 [1] number of IO-APIC #5 registers: 16. Jan 7 09:40:27 [2] testing the IO APIC. Jan 7 09:40:27 [4] Jan 7 09:40:27 [1] IO APIC #4 Jan 7 09:40:27 [1] register #00: 04000000 Jan 7 09:40:27 [1] . : physical APIC id: 04 Jan 7 09:40:27 [1] . : Delivery Type: 0 Jan 7 09:40:27 [1] . : LTS : 0 Jan 7 09:40:27 [1] register #01: 000F0011 Jan 7 09:40:27 [1] . : max redirection entries: 000F Jan 7 09:40:27 [1] . : PRQ implemented: 0 Jan 7 09:40:27 [1] . : IO APIC version: 0011 Jan 7 09:40:27 [1] register #02: 00000000 Jan 7 09:40:27 [1] . : arbitration: 00 Jan 7 09:40:27 [1] IRQ redirection table: Jan 7 09:40:27 [1] NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: Jan 7 09:40:27 [1] 00 001 01 0 0 0 0 0 1 1 31 Jan 7 09:40:27 [1] 01 001 01 0 0 0 0 0 1 1 39 Jan 7 09:40:27 [1] 02 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 03 001 01 0 0 0 0 0 1 1 41 Jan 7 09:40:27 [1] 04 001 01 0 0 0 0 0 1 1 49 Jan 7 09:40:27 [1] 05 001 01 0 0 0 0 0 1 1 51 Jan 7 09:40:27 [1] 0 0 0 0 0 1 1 59 Jan 7 09:40:27 [1] 07 001 01 0 0 0 0 0 1 1 61 Jan 7 09:40:27 [1] 08 001 01 0 0 0 0 0 1 1 69 Jan 7 09:40:27 [1] 09 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 0a 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 0b 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 0c 001 01 0 0 0 0 0 1 1 71 Jan 7 09:40:27 [1] 0d 001 01 0 0 0 0 0 1 1 79 Jan 7 09:40:27 [1] 0e 001 01 0 0 0 0 0 1 1 81 Jan 7 09:40:27 [1] 0f 001 01 0 0 0 0 0 1 1 89 Jan 7 09:40:27 [4] Jan 7 09:40:27 [1] IO APIC #5 Jan 7 09:40:27 [1] register #00: 05000000 Jan 7 09:40:27 [1] . : physical APIC id: 05 Jan 7 09:40:27 [1] . : Delivery Type: 0 Jan 7 09:40:27 [1] . : LTS : 0 Jan 7 09:40:27 [1] register #01: 000F0011 Jan 7 09:40:27 [1] . : max redirection entries: 000F Jan 7 09:40:27 [1] . : PRQ implemented: 0 Jan 7 09:40:27 [1] . : IO APIC version: 0011 Jan 7 09:40:27 [1] register #02: 01000000 Jan 7 09:40:27 [1] . : arbitration: 01 Jan 7 09:40:27 [1] IRQ redirection table: Jan 7 09:40:27 [1] NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: Jan 7 09:40:27 [1] 00 09C 0C 1 0 0 0 0 1 2 16 Jan 7 09:40:27 [1] 01 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 02 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 03 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 04 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 05 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 06 001 01 1 1 0 1 0 1 1 91 Jan 7 09:40:27 [1] 07 001 01 1 1 0 1 0 1 1 99 Jan 7 09:40:27 [1] 08 003 03 1 0 0 0 0 1 2 2D Jan 7 09:40:27 [1] 09 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 0a 086 06 1 0 0 0 0 0 2 28 Jan 7 09:40:27 [1] 0b 001 01 1 1 0 1 0 1 1 A1 Jan 7 09:40:27 [1] 0c 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 0d 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 0e 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] 0f 000 00 1 0 0 0 0 0 0 00 Jan 7 09:40:27 [1] IRQ to pin mappings: Jan 7 09:40:27 [1] IRQ0 -> 0:0 Jan 7 09:40:27 [1] IRQ1 -> 0:1 Jan 7 09:40:27 [1] IRQ3 -> 0:3 Jan 7 09:40:27 [1] IRQ4 -> 0:4 Jan 7 09:40:27 [1] IRQ5 -> 0:5 Jan 7 09:40:27 [1] IRQ6 -> 0:6 Jan 7 09:40:27 [1] IRQ7 -> 0:7 Jan 7 09:40:27 [1] IRQ8 -> 0:8 Jan 7 09:40:27 [1] IRQ12 -> 0:12 Jan 7 09:40:27 [1] IRQ13 -> 0:13 Jan 7 09:40:27 [1] IRQ14 -> 0:14 Jan 7 09:40:27 [1] IRQ15 -> 0:15 Jan 7 09:40:27 [1] IRQ22 -> 1:6 Jan 7 09:40:27 [1] IRQ23 -> 1:7 Jan 7 09:40:27 [1] IRQ27 -> 1:11 Jan 7 09:40:27 [2] done. Jan 7 09:40:27 [4] Using local APIC timer interrupts. Jan 7 09:40:27 [4] calibrating APIC timer . Jan 7 09:40:27 [4] . CPU clock speed is 797.4693 MHz. Jan 7 09:40:27 [4] . host bus clock speed is 132.9113 MHz. Jan 7 09:40:27 [4] cpu: 0, clocks: 1329113, slice: 664556 Jan 7 09:40:27 [4] CPU0 Jan 7 09:40:27 [4] mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) Jan 7 09:40:27 [4] mtrr: detected mtrr type: Intel Jan 7 09:40:27 [2] ACPI: Subsystem revision 20040326 Jan 7 09:40:27 [2] ACPI: Interpreter disabled. Jan 7 09:40:27 [2] PCI: PCI BIOS revision 2.10 entry at 0xfdbc1, last bus=1 Jan 7 09:40:27 [2] PCI: Using configuration type 1 Jan 7 09:40:27 [2] PCI: Probing PCI hardware Jan 7 09:40:27 [4] PCI: Probing PCI hardware (bus 00) Jan 7 09:40:27 [2] PCI: Discovered primary peer bus 01 [IRQ] Jan 7 09:40:27 [2] PCI: Using IRQ router ServerWorks [1166/0200] at 00:0f.0 Jan 7 09:40:27 [2] PCI->APIC IRQ transform: (B0,I1,P0) -> 22 Jan 7 09:40:27 [2] PCI->APIC IRQ transform: (B1,I2,P0) -> 27 Jan 7 09:40:27 [2] PCI->APIC IRQ transform: (B1,I3,P0) -> 23 Jan 7 09:40:27 [5] PCI: Cannot allocate resource region 0 of device 00:0f.2 Jan 7 09:40:27 [2] Linux NET4.0 for Linux 2.4 Jan 7 09:40:27 [2] Based upon Swansea University Computer Society NET3.039 Jan 7 09:40:27 [4] Initializing RT netlink socket Jan 7 09:40:27 [4] Starting kswapd Jan 7 09:40:27 [2] Journalled Block Device driver loaded Jan 7 09:40:27 [2] devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) Jan 7 09:40:27 [2] devfs: boot_options: 0x1 Jan 7 09:40:27 [2] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Jan 7 09:40:27 [4] pty: 256 Unix98 ptys configured Jan 7 09:40:27 [2] Real Time Clock Driver v1.10f Jan 7 09:40:27 [4] keyboard: Timeout - AT keyboard not present?(ed) Jan 7 09:40:27 [4] keyboard: Timeout - AT keyboard not present?(f4) Jan 7 09:40:27 [4] floppy0: no floppy controllers found Jan 7 09:40:27 [4] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Jan 7 09:40:27 [2] loop: loaded (max 8 devices) Jan 7 09:40:27 [2] Intel(R) PRO/1000 Network Driver - version 7.3.20-k4 Jan 7 09:40:27 [2] Copyright (c) 1999-2006 Intel Corporation. Jan 7 09:40:27 [2] dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15 Jan 7 09:40:27 [4] FW Version=$Version$ Jan 7 09:40:27 [2] pcnet32.c:v1.30h 06.24.2004 tsbogend@alpha.franken.de Jan 7 09:40:27 [2] ThunderLAN driver v1.15 Jan 7 09:40:27 [2] TLAN: 0 devices installed, PCI: 0 EISA: 0 Jan 7 09:40:27 [2] dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17) Jan 7 09:40:27 [2] ns83820.c: National Semiconductor DP83820 10/100/1000 driver. Jan 7 09:40:27 [4] >sk98lin: No adapter found. Jan 7 09:40:27 [2] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.50. Jan 7 09:40:27 [2] r8169 Gigabit Ethernet driver 1.2 loaded Jan 7 09:40:27 [1] eth0: Identified chip type is 'RTL8169s/8110s'. Jan 7 09:40:27 [2] eth0: RTL8169 at 0xe0800c00, 00:0f:b5:f6:97:31, IRQ 23 Jan 7 09:40:27 [2] eth0: Auto-negotiation Enabled. Jan 7 09:40:27 [2] eth0: 1000Mbps Full-duplex operation. Jan 7 09:40:27 [2] Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 Jan 7 09:40:27 [2] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Jan 7 09:40:27 [2] SvrWks OSB4: IDE controller at PCI slot 00:0f.1 Jan 7 09:40:27 [2] SvrWks OSB4: chipset revision 0 Jan 7 09:40:27 [2] SvrWks OSB4: not 100% native mode: will probe irqs later Jan 7 09:40:27 [2] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio Jan 7 09:40:27 [2] ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio Jan 7 09:40:27 [4] hda: SanDisk SDCFB-32, CFA DISK drive Jan 7 09:40:27 [4] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Jan 7 09:40:27 [4] hda: attached ide-disk driver. Jan 7 09:40:27 [2] hda: 62720 sectors (32 MB) w/1KiB Cache, CHS=490/4/32 Jan 7 09:40:27 [2] Partition check: Jan 7 09:40:27 [2] /dev/ide/host0/bus0/target0/lun0: p1 p2 Jan 7 09:40:27 [2] SCSI subsystem driver Revision: 1.00 Jan 7 09:40:27 [2] Loading Adaptec I2O RAID: Version 2.4 Build 5 Jan 7 09:40:27 [2] Detecting Adaptec I2O RAID controllers. Jan 7 09:40:27 [2] Red Hat/Adaptec aacraid driver (1.1-3 Jul 16 2008 21:50:42) Jan 7 09:40:27 [4] scsi: Detection failed (no card) Jan 7 09:40:27 [3] megaraid: v2.10.10.1 (Release Date: Thu Jan 27 16:19:44 EDT 2005) Jan 7 09:40:27 [3] megaraid: found 0x1000:0x1960:bus 1:slot 2:func 0 Jan 7 09:40:27 [3] scsi1:Found MegaRAID controller at 0xe0804000, IRQ:27 Jan 7 09:40:27 [3] megaraid: [713N:G119] detected 1 logical drives. Jan 7 09:40:27 [3] megaraid: supports extended CDBs. Jan 7 09:40:27 [2] megaraid: channel[0] is raid. Jan 7 09:40:27 [2] scsi1 : LSI Logic MegaRAID 713N 254 commands 16 targs 4 chans 7 luns Jan 7 09:40:27 [3] scsi1: scanning scsi channel 0 for logical drives. Jan 7 09:40:27 [4] Vendor: MegaRAID Model: LD 0 RAID5 1430G Rev: 713N Jan 7 09:40:27 [4] Type: Direct-Access ANSI SCSI revision: 02 Jan 7 09:40:27 [3] scsi1: scanning scsi channel 1 for logical drives. Jan 7 09:40:27 [3] scsi1: scanning scsi channel 2 for logical drives. Jan 7 09:40:27 [3] scsi1: scanning scsi channel 3 for logical drives. Jan 7 09:40:27 [3] scsi1: scanning scsi channel 4 [P0] for physical devices. Jan 7 09:40:27 [4] GDT-HA: Storage RAID Controller Driver. Version: 3.04 Jan 7 09:40:27 [4] GDT-HA: Found 0 PCI Storage RAID Controllers Jan 7 09:40:27 [2] scsi2 : SCSI host adapter emulation for IDE ATAPI devices Jan 7 09:40:27 [4] 3ware Storage Controller device driver for Linux v1.02.00.037. Jan 7 09:40:27 [4] 3w-xxxx: No cards found. Jan 7 09:40:27 [1] libata version 1.20 loaded. Jan 7 09:40:27 [4] Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 Jan 7 09:40:27 [4] SCSI device sda: 2930309120 512-byte hdwr sectors (1500318 MB) Jan 7 09:40:27 [2] /dev/scsi/host1/bus0/target0/lun0: p1 Jan 7 09:40:27 [2] raw1394: /dev/raw1394 device initialized Jan 7 09:40:27 [2] sbp2: $Rev: 1074 $ Ben Collins Jan 7 09:40:27 [5] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1) Jan 7 09:40:27 [2] usb.c: registered new driver usbdevfs Jan 7 09:40:27 [2] usb.c: registered new driver hub Jan 7 09:40:27 [2] host/uhci.c: USB Universal Host Controller Interface driver v1.1 Jan 7 09:40:27 [4] PCI: Enabling device 00:0f.2 (0000 -> 0002) Jan 7 09:40:27 [4] PCI: No IRQ known for interrupt pin A of device 00:0f.2. Probably buggy MP table. Jan 7 09:40:27 [2] usb.c: registered new driver usbkbd Jan 7 09:40:27 [2] usbkbd.c: :USB HID Boot Protocol keyboard driver Jan 7 09:40:27 [2] Initializing USB Mass Storage driver. Jan 7 09:40:27 [2] usb.c: registered new driver usb-storage Jan 7 09:40:27 [2] USB Mass Storage support registered. Jan 7 09:40:27 [2] NET4: Linux TCP/IP 1.0 for NET4.0 Jan 7 09:40:27 [2] IP Protocols: ICMP, UDP, TCP Jan 7 09:40:27 [2] IP: routing cache hash table of 4096 buckets, 32Kbytes Jan 7 09:40:27 [2] TCP: Hash tables configured (established 131072 bind 65536) Jan 7 09:40:27 [2] NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Jan 7 09:40:27 [3] RAMDISK: NASLite file system found at block 0 Jan 7 09:40:27 [4] <6>Freeing initrd memory: 4006k freed Jan 7 09:40:27 [4] VFS: Mounted root (ext2 filesystem). Jan 7 09:40:27 [2] Mounted devfs on /dev Jan 7 09:40:27 [2] Freeing unused kernel memory: 556k freed Jan 7 09:40:27 [2] /dev/ide/host0/bus0/target0/lun0: p1 p2 Jan 7 09:40:27 [2] kjournald starting. Commit interval 5 seconds Jan 7 09:40:27 [2] EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal Jan 7 09:40:27 [2] EXT3-fs: mounted filesystem with ordered data mode. Jan 7 09:40:27 [2] Adding Swap: 1028088k swap-space (priority -1)

System message priority, in ascending order, is as follows: [1] - DEBUG, [2] - INFO, [3] - NOTICE, [4] - WARNING, [5] - ERROR, [6] - CRITICAL, [7] - ALERT, [8] - EMERGENCY. The priority defines the severity of the message where CRITICAL, ALERT and EMERGENCY may warrant immediate attention.