|
| |
| Server Storage Disk-0 |
 |
General:This page provides specific information pertaining to Disk-0. Hardware, filesystem and S.M.A.R.T. details are listed below.
Disk-0 Hardware Details: MODEL: SAMSUNG SP1604N, SN# S013J10Y324306, v.TM100-30
INTERFACE: IDE, HOST-0, BUS-0, TARGET-0, LUN-0
Filesystem Details: | | tune2fs 1.27 (8-Mar-2002)
Filesystem volume name: NASLite-SE000161
Last mounted on:
Filesystem UUID: d39fdd8a-3506-45ce-bcc6-356c79328276
Filesystem magic number: 0xEF53
Filesystem revision #: 1 (dynamic)
Filesystem features: has_journal filetype needs_recovery sparse_super
Filesystem state: clean
Errors behavior: Continue
Filesystem OS type: Linux
Inode count: 19546112
Block count: 39070080
Reserved block count: 0
Free blocks: 24663709
Free inodes: 19406568
First block: 0
Block size: 4096
Fragment size: 4096
Blocks per group: 32768
Fragments per group: 32768
Inodes per group: 16384
Inode blocks per group: 512
Last mount time: Fri Sep 29 23:21:33 2006
Last write time: Fri Sep 29 23:21:33 2006
Mount count: 10
Maximum mount count: 29
Last checked: Tue Sep 26 16:42:06 2006
Check interval: 15552000 (6 months)
Next check after: Sun Mar 25 16:42:06 2007
Reserved blocks uid: 0 (user admin)
Reserved blocks gid: 0 (group admin)
First inode: 11
Inode size: 128
Journal UUID:
Journal inode: 8
Journal device: 0x0000
First orphan inode: 0 |
 |
S.M.A.R.T. Status: | | smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG SP1604N
Serial Number: S013J10Y324306
Firmware Version: TM100-30
User Capacity: 160,041,885,696 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Mon Oct 2 21:18:01 2006 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (6000) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 100) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 2
3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always - 6848
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 10
5 Reallocated_Sector_Ct 0x0033 100 100 011 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 0
9 Power_On_Half_Minutes 0x0032 100 100 000 Old_age Always - 225h+01m
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 6
194 Temperature_Celsius 0x0022 115 109 000 Old_age Always - 41
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 1644723
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 051 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 100 100 051 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 5
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 5 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 4f c2 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d9 00 01 4f c2 a0 00 00:00:07.438 SMART DISABLE OPERATIONS
ec 00 ff 01 00 00 a0 00 00:00:07.438 IDENTIFY DEVICE
10 00 ff 01 00 00 a0 00 00:00:07.438 RECALIBRATE [OBS-4]
91 00 ff 01 00 00 af 00 00:00:07.438 INITIALIZE DEVICE PARAMETERS [OBS-6]
ec 00 ff 01 00 00 a0 00 00:00:07.375 IDENTIFY DEVICE
Error 4 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 4f c2 f0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 da 00 00 4f c2 f0 00 00:01:08.875 SMART RETURN STATUS
ec 00 00 00 4f c2 f0 00 00:01:08.875 IDENTIFY DEVICE
Error 3 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 4f c2 f0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 da 00 00 4f c2 f0 00 00:01:08.813 SMART RETURN STATUS
ec 00 00 37 00 00 f0 00 00:01:08.813 IDENTIFY DEVICE
ef 02 00 00 00 00 f0 00 00:00:54.313 SET FEATURES [Enable write cache]
c6 00 10 00 00 00 f0 00 00:00:54.313 SET MULTIPLE MODE
f8 00 00 00 00 00 f0 00 00:00:54.313 READ NATIVE MAX ADDRESS
Error 2 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 4f c2 f0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 da 00 00 4f c2 f0 00 00:01:09.125 SMART RETURN STATUS
ec 00 00 00 4f c2 f0 00 00:01:09.125 IDENTIFY DEVICE
Error 1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 4f c2 f0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 da 00 00 4f c2 f0 00 00:01:09.063 SMART RETURN STATUS
ec 00 00 37 00 00 f0 00 00:01:09.063 IDENTIFY DEVICE
ef 02 00 00 00 00 f0 00 00:00:54.563 SET FEATURES [Enable write cache]
c6 00 10 00 00 00 f0 00 00:00:54.563 SET MULTIPLE MODE
f8 00 00 00 00 00 f0 00 00:00:54.563 READ NATIVE MAX ADDRESS
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 114 -
# 2 Extended offline Completed without error 00% 2 -
Device does not support Selective Self Tests/Logging |
|
