NASLite Network Attached Storage

www.serverelements.com
Task-specific simplicity with low hardware requirements.
It is currently Fri Dec 03, 2021 1:43 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 3 posts ] 
Author Message
PostPosted: Sat Nov 13, 2010 12:55 pm 
Offline

Joined: Sat Nov 13, 2010 12:45 pm
Posts: 7
I've been using NASLite for a bit now, and recently bought a new hard drive to go in it, but I'm encountering a bit of a snag. If anyone can suggest a way forward I'd be very grateful.

The Drive:

SAMSUNG HD154UI, ATA DISK drive
attached ide-disk driver.
host protected area => 1
-1364690128 sectors (1500302 MB) w/32767KiB Cache, CHS=182401/255/63, UDMA(33)

The error message:

umount: /export/Disk-3: No such file or directory
Checking that no-one is using this disk right now ...
OK

Disk /dev/ide/host0/bus1/target0/lun0/disc: 182401 cylinders, 255 heads, 63 sect
ors/track
Old situation:
Warning: The partition table looks like it was made
for C/H/S=*/16/63 (instead of 182401/255/63).
For this listing I'll assume that geometry.
Units = cylinders of 516096 bytes, blocks of 1024 bytes, counting from 0

Device Boot Start End #cyls #blocks Id System
/dev/ide/host0/bus1/target0/lun0/part1 * 0+ 2907017 2907018- 1465137040+
6 FAT16
/dev/ide/host0/bus1/target0/lun0/part2 0 - 0 0
0 Empty
/dev/ide/host0/bus1/target0/lun0/part3 0 - 0 0
0 Empty
/dev/ide/host0/bus1/target0/lun0/part4 0 - 0 0
0 Empty
no room for partition descriptor

sfdisk: bad input
mke2fs 1.27 (8-Mar-2002)
/dev/ide/host0/bus1/target0/lun0/part1: Memory allocation failed while setting u
p superblock

Failed to configure Disk-3. Disk-3 can be configured only
if it is installed and is a fixed disk. CD-ROM, DVD-ROM, ZIP and other
ATAPI drives that are not fixed disks can not be configured for use
with NASLite.


The system is:

Processor (CPU)
vendor_id : GenuineIntel
model name : Pentium MMX
cpu MHz : 199.615
bogomips : 398.13


--------------------------------------------------------------------------------
Memory
total used free shared buffers
Mem: 62924 11288 51636 0 148


--------------------------------------------------------------------------------
Disks
Filesystem Size Used Available Use% Device
System 3.9M 2.4M 1.5M 61% RAM Disk
Storage Area 3.2G 86.3M 3.1G 3% NAS Disk-1
Storage Area 3.2G 2.2G 987.9M 70% NAS Disk-2


Thanks, Alan


Top
 Profile  
 
PostPosted: Sat Nov 13, 2010 3:40 pm 
Offline

Joined: Sun May 27, 2007 5:38 pm
Posts: 517
Location: gods own country
assuming this is in the correct section and you are using the 'free' naslite i think your problem probarbly is that the software will not support the drive you have added - which, by the reference posted is a 1.5Tb SATA drive

plus from memory the free version has a restriction on the number of drives it supports - you need to do a bit of reading of the manual

upgrading to naslite 2 or M2 would certainly support the new drive


Top
 Profile  
 
PostPosted: Tue Nov 16, 2010 6:39 pm 
Offline

Joined: Sat Nov 13, 2010 12:45 pm
Posts: 7
Quote:
the software will not support the drive you have added


Thanks, I was afraid that might be the case.

NASLite-2 it is then.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group