NASLite Network Attached Storage

I am having a issue during a 200 GB Rsync between servers. I receive a Code 23 during Rsync and in the SYSLOGs I receive the below message various times. I am looking for additional ideas to try an remove these error messages

# Jan 8 23:46:26 user.warn kernel: ata2: status=0x50 { DriveReady SeekComplete }
# Jan 8 23:46:26 user.warn kernel: SCSI disk error : host 2 channel 0 id 0 lun 0 return code = 8000002
# Jan 8 23:46:26 user.warn kernel: Current sd08:11: sns = 70 0
# Jan 8 23:46:26 user.warn kernel: Raw sense data:0x70 0x00 0x00 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
# Jan 8 23:46:26 user.warn kernel: I/O error: dev 08:11, sector 369196408

This only happens during a Rsync to a different server. If I perform an Rsync between Disk-1 (Host 2) and Disk 3 (Host 4), I do not receive errors.

I have:
Turned off all unrequired devices (Com 1,2 LPT1,USB,Internal SATA)
Each remaining device on own IRQ, VGA 11, Promise SATA 10, Ethernet 5
I have replaced the SATA cable with confirmed SATAII compatible cables

My current setup
NASlite CDD 2.06
Compaq EVO D530 3.0Gz 1 GB Ram
Internal GB ethernet (Broadcom 5782)
Promise SATA300 TX4 4PORT
4 - Seagate ST3500630AS 500GB Drives

Below is my SYSLOG

Thanks for any ideas
Carson

# Jan 8 19:51:57 user.notice kernel: klogd started: BusyBox v1.01 (2007.03.15-22:03+0000)
# Jan 8 19:51:57 user.warn kernel: Linux version 2.4.35.NASLite (root@tzt) (gcc version 3.4.6) #2 Sun Aug 12 09:03:16 EDT 2007
# Jan 8 19:51:57 user.info kernel: BIOS-provided physical RAM map:
# Jan 8 19:51:57 user.warn kernel: BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
# Jan 8 19:51:57 user.warn kernel: BIOS-e820: 000000000009d400 - 00000000000a0000 (reserved)
# Jan 8 19:51:57 user.warn kernel: BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
# Jan 8 19:51:57 user.warn kernel: BIOS-e820: 0000000000100000 - 000000003f7f0000 (usable)
# Jan 8 19:51:57 user.warn kernel: BIOS-e820: 000000003f7f0000 - 0000000040000000 (reserved)
# Jan 8 19:51:57 user.warn kernel: BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
# Jan 8 19:51:57 user.notice kernel: 119MB HIGHMEM available.
# Jan 8 19:51:57 user.notice kernel: 896MB LOWMEM available.
# Jan 8 19:51:57 user.warn kernel: On node 0 totalpages: 260080
# Jan 8 19:51:57 user.warn kernel: zone(0): 4096 pages.
# Jan 8 19:51:57 user.warn kernel: zone(1): 225280 pages.
# Jan 8 19:51:57 user.warn kernel: zone(2): 30704 pages.
# Jan 8 19:51:57 user.info kernel: ACPI: RSDP (v000 COMPAQ ) @ 0x000e9e10
# Jan 8 19:51:57 user.info kernel: ACPI: RSDT (v001 COMPAQ CPQ0064 0x20040115 0x00000000) @ 0x000e5640
# Jan 8 19:51:57 user.info kernel: ACPI: FADT (v001 COMPAQ SPRINGD 0x00000001 0x00000000) @ 0x000e56f8
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ PROJECT 0x00000001 MSFT 0x0100000e) @ 0x000e6585
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ CORE_PNP 0x00000001 MSFT 0x0100000e) @ 0x000e6c0a
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ CORE_UTL 0x00000001 MSFT 0x0100000e) @ 0x000e7156
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ VILLTBL1 0x00000001 MSFT 0x0100000e) @ 0x000e7348
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ LGCYLITE 0x00000001 MSFT 0x0100000e) @ 0x000e7676
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ UART2 0x00000001 MSFT 0x0100000e) @ 0x000e7bb5
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ FLOPPY 0x00000001 MSFT 0x0100000e) @ 0x000e7d1c
# Jan 8 19:51:57 user.info kernel: ACPI: MADT (v001 COMPAQ SPRINGD 0x00000001 0x00000000) @ 0x000e576c
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ APIC 0x00000001 MSFT 0x0100000e) @ 0x000e9b2c
# Jan 8 19:51:57 user.info kernel: ACPI: ASF! (v016 COMPAQ SPRINGD 0x00000001 0x00000000) @ 0x000e57d4
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ PNP_PRSS 0x00000001 MSFT 0x0100000e) @ 0x000e82d8
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ UR2_PRSS 0x00000001 MSFT 0x0100000e) @ 0x000e86e7
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ FPY_PRSS 0x00000001 MSFT 0x0100000e) @ 0x000e8854
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ S3 0x00000001 MSFT 0x0100000e) @ 0x000e8a22
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ CORE_S3 0x00000001 MSFT 0x0100000e) @ 0x000e8b89
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ SIDETM 0x00000001 MSFT 0x0100000e) @ 0x000e8daa
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ GTF2 0x00000001 MSFT 0x0100000e) @ 0x000e956f
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ L08 0x00000001 MSFT 0x0100000e) @ 0x000e98e3
# Jan 8 19:51:57 user.info kernel: ACPI: SSDT (v001 COMPAQ FINIS 0x00000001 MSFT 0x0100000e) @ 0x000e9d30
# Jan 8 19:51:57 user.info kernel: ACPI: DSDT (v001 COMPAQ DSDT 0x00000001 MSFT 0x0100000e) @ 0x00000000
# Jan 8 19:51:57 user.warn kernel: Kernel command line: rw root=/dev/ram0 initrd=NASLite.02 quiet BOOT_IMAGE=NASLite.01
# Jan 8 19:51:57 user.info kernel: Initializing CPU#0
# Jan 8 19:51:57 user.warn kernel: Detected 2992.620 MHz processor.
# Jan 8 19:51:57 user.warn kernel: Console: colour VGA+ 80x25
# Jan 8 19:51:57 user.warn kernel: Calibrating delay loop. 5976.88 BogoMIPS
# Jan 8 19:51:57 user.info kernel: Memory: 1022072k/1040320k available (2214k kernel code, 17852k reserved, 642k data, 540k init, 122816k highmem)
# Jan 8 19:51:57 user.info kernel: Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
# Jan 8 19:51:57 user.info kernel: Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
# Jan 8 19:51:57 user.info kernel: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
# Jan 8 19:51:57 user.info kernel: Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
# Jan 8 19:51:57 user.warn kernel: Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
# Jan 8 19:51:57 user.info kernel: CPU: Trace cache: 12K uops, L1 D cache: 16K
# Jan 8 19:51:57 user.info kernel: CPU: L2 cache: 1024K
# Jan 8 19:51:57 user.debug kernel: CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
# Jan 8 19:51:57 user.debug kernel: CPU: Common caps: bfebfbff 00000000 00000000 00000000
# Jan 8 19:51:57 user.warn kernel: CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04
# Jan 8 19:51:57 user.info kernel: Enabling fast FPU save and restore. done.
# Jan 8 19:51:57 user.info kernel: Enabling unmasked SIMD FPU exception support. done.
# Jan 8 19:51:57 user.info kernel: Checking 'hlt' instruction. OK.
# Jan 8 19:51:57 user.warn kernel: ACPI: IRQ9 SCI: Edge set to Level Trigger.
# Jan 8 19:51:57 user.warn kernel: POSIX conformance testing by UNIFIX
# Jan 8 19:51:57 user.warn kernel: mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
# Jan 8 19:51:57 user.warn kernel: mtrr: detected mtrr type: Intel
# Jan 8 19:51:57 user.info kernel: ACPI: Subsystem revision 20040326
# Jan 8 19:51:57 user.info kernel: PCI: PCI BIOS revision 2.20 entry at 0xec1a9, last bus=5
# Jan 8 19:51:57 user.info kernel: PCI: Using configuration type 1
# Jan 8 19:51:57 user.info kernel: ACPI: Interpreter enabled
# Jan 8 19:51:57 user.info kernel: ACPI: Using PIC for interrupt routing
# Jan 8 19:51:57 user.info kernel: ACPI: System [ACPI] (supports S0 S1 S3 S4 S5)
# Jan 8 19:51:57 user.warn kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 14 15)
# Jan 8 19:51:57 user.warn kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
# Jan 8 19:51:57 user.warn kernel: KC] (IRQs 3 4 5 6 7 *10 11 14 15)
# Jan 8 19:51:57 user.warn kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 14 15)
# Jan 8 19:51:57 user.warn kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 14 15)
# Jan 8 19:51:57 user.warn kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
# Jan 8 19:51:57 user.warn kernel: ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
# Jan 8 19:51:57 user.warn kernel: ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 14 15)
# Jan 8 19:51:57 user.info kernel: ACPI: PCI Root Bridge [PCI0] (00:00)
# Jan 8 19:51:57 user.warn kernel: PCI: Probing PCI hardware (bus 00)
# Jan 8 19:51:57 user.info kernel: PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
# Jan 8 19:51:57 user.warn kernel: Transparent bridge - PCI device 8086:244e
# Jan 8 19:51:57 user.debug kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
# Jan 8 19:51:57 user.debug kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
# Jan 8 19:51:57 user.info kernel: PCI: Probing PCI hardware
# Jan 8 19:51:57 user.warn kernel: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
# Jan 8 19:51:57 user.warn kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
# Jan 8 19:51:57 user.warn kernel: ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 5
# Jan 8 19:51:57 user.info kernel: PCI: Using ACPI for IRQ routing
# Jan 8 19:51:57 user.info kernel: Linux NET4.0 for Linux 2.4
# Jan 8 19:51:57 user.info kernel: Based upon Swansea University Computer Society NET3.039
# Jan 8 19:51:57 user.warn kernel: Initializing RT netlink socket
# Jan 8 19:51:57 user.warn kernel: Starting kswapd
# Jan 8 19:51:57 user.warn kernel: allocated 32 pages and 32 bhs reserved for the highmem bounces
# Jan 8 19:51:57 user.info kernel: Journalled Block Device driver loaded
# Jan 8 19:51:57 user.info kernel: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
# Jan 8 19:51:57 user.info kernel: devfs: boot_options: 0x1
# Jan 8 19:51:57 user.info kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
# Jan 8 19:51:57 user.info kernel: ACPI: Power Button (FF) [PWRF]
# Jan 8 19:51:57 user.info kernel: ACPI: Processor [CPU0] (supports C1, 8 throttling states)
# Jan 8 19:51:57 user.info kernel: ACPI: Processor [CPU1] (supports C1, 8 throttling states)
# Jan 8 19:51:57 user.warn kernel: pty: 256 Unix98 ptys configured
# Jan 8 19:51:57 user.info kernel: Real Time Clock Driver v1.10f
# Jan 8 19:51:57 user.info kernel: Floppy drive(s): fd0 is 1.44M
# Jan 8 19:51:57 user.info kernel: FDC 0 is a post-1991 82077
# Jan 8 19:51:57 user.warn kernel: RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
# Jan 8 19:51:57 user.info kernel: loop: loaded (max 8 devices)
# Jan 8 19:51:57 user.info kernel: Intel(R) PRO/1000 Network Driver - version 7.3.20-k4
# Jan 8 19:51:57 user.info kernel: Copyright (c) 1999-2006 Intel Corporation.
# Jan 8 19:51:57 user.info kernel: dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15
# Jan 8 19:51:57 user.warn kernel: FW Version=$Version$
# Jan 8 19:51:57 user.info kernel: pcnet32.c:v1.30h 06.24.2004 tsbogend@alpha.franken.de
# Jan 8 19:51:57 user.info kernel: ThunderLAN driver v1.15
# Jan 8 19:51:57 user.info kernel: TLAN: 0 devices installed, PCI: 0 EISA: 0
# Jan 8 19:51:57 user.info kernel: dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
# Jan 8 19:51:57 user.info kernel: ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
# Jan 8 19:51:57 user.info kernel: tg3.c:v3.26 (April 24, 2005)
# Jan 8 19:51:57 user.info kernel: eth0: Tigon3 [partno(BCM95782A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:11:85:dd:a4:31
# Jan 8 19:51:57 user.info kernel: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[0]
# Jan 8 19:51:57 user.info kernel: eth0: dma_rwctrl[763f0000]
# Jan 8 19:51:57 user.warn kernel: sk98lin: No adapter found.
# Jan 8 19:51:57 user.info kernel: forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.50.
# Jan 8 19:51:57 user.info kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
# Jan 8 19:51:57 user.info kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
# Jan 8 19:51:57 user.info kernel: ICH5: IDE controller at PCI slot 00:1f.1
# Jan 8 19:51:57 user.warn kernel: PCI: Enabling device 00:1f.1 (0005 -> 0007)
# Jan 8 19:51:57 user.info kernel: ICH5: chipset revision 2
# Jan 8 19:51:57 user.info kernel: ICH5: not 100% native mode: will probe irqs later
# Jan 8 19:51:57 user.info kernel: ide0: BM-DMA at 0x2080-0x2087, BIOS settings: hda:pio, hdb:pio
# Jan 8 19:51:57 user.info kernel: ide1: BM-DMA at 0x2088-0x208f, BIOS settings: hdc:DMA, hdd:pio
# Jan 8 19:51:57 user.warn kernel: hdc: HL-DT-ST RW/DVD GCC-4481B, ATAPI CD/DVD-ROM drive
# Jan 8 19:51:57 user.warn kernel: ide1 at 0x170-0x177,0x376 on irq 15
# Jan 8 19:51:57 user.info kernel: SCSI subsystem driver Revision: 1.00
# Jan 8 19:51:57 user.info kernel: Loading Adaptec I2O RAID: Version 2.4 Build 5
# Jan 8 19:51:57 user.info kernel: Detecting Adaptec I2O RAID controllers.
# Jan 8 19:51:57 user.info kernel: Red Hat/Adaptec aacraid driver (1.1-3 Aug 12 2007 09:05:44)
# Jan 8 19:51:57 user.warn kernel: scsi: Detection failed (no card)
# Jan 8 19:51:57 user.notice kernel: megaraid: v2.10.10.1 (Release Date: Thu Jan 27 16:19:44 EDT 2005)
# Jan 8 19:51:57 user.warn kernel: GDT-HA: Storage RAID Controller Driver. Version: 3.04
# Jan 8 19:51:57 user.warn kernel: GDT-HA: Found 0 PCI Storage RAID Controllers
# Jan 8 19:51:57 user.warn kernel: 3ware Storage Controller device driver for Linux v1.02.00.037.
# Jan 8 19:51:57 user.warn kernel: 3w-xxxx: No cards found.
# Jan 8 19:51:57 user.debug kernel: libata version 1.20 loaded.
# Jan 8 19:51:57 user.debug kernel: PCI(00:1f.2): version 1.05
# Jan 8 19:51:57 user.err kernel: PCI: Device 00:1f.2 not available because of resource collisions
# Jan 8 19:51:57 user.debug kernel: PCI(05:09.0): version 1.03
# Jan 8 19:51:57 user.info kernel: ata1: SATA max UDMA/133 cmd 0xF8811200 ctl 0xF8811238 bmdma 0x0 irq 10
# Jan 8 19:51:57 user.info kernel: ata2: SATA max UDMA/133 cmd 0xF8811280 ctl 0xF88112B8 bmdma 0x0 irq 10
# Jan 8 19:51:57 user.info kernel: ata3: SATA max UDMA/133 cmd 0xF8811300 ctl 0xF8811338 bmdma 0x0 irq 10
# Jan 8 19:51:57 user.info kernel: ata4: SATA max UDMA/133 cmd 0xF8811380 ctl 0xF88113B8 bmdma 0x0 irq 10
# Jan 8 19:51:57 user.debug kernel: 84:4023 85:3469 86:3c01 87:4023 88:407f
# Jan 8 19:51:57 user.info kernel: ata1: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
# Jan 8 19:51:57 user.info kernel: ata1: dev 0 configured for UDMA/133
# Jan 8 19:51:57 user.debug kernel: ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
# Jan 8 19:51:57 user.info kernel: ata2: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
# Jan 8 19:51:57 user.info kernel: ata2: dev 0 configured for UDMA/133
# Jan 8 19:51:57 user.debug kernel: ata3: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
# Jan 8 19:51:57 user.info kernel: ata3: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
# Jan 8 19:51:57 user.info kernel: ata3: dev 0 configured for UDMA/133
# Jan 8 19:51:57 user.debug kernel: ata4: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
# Jan 8 19:51:57 user.info kernel: ata4: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
# Jan 8 19:51:57 user.info kernel: ata4: dev 0 configured for UDMA/133
# Jan 8 19:51:57 user.info kernel: scsi1 : sata_promise
# Jan 8 19:51:57 user.info kernel: scsi2 : sata_promise
# Jan 8 19:51:57 user.info kernel: scsi3 : sata_promise
# Jan 8 19:51:57 user.info kernel: scsi4 : sata_promise
# Jan 8 19:51:57 user.warn kernel: Vendor: ATA Model: ST3500630AS Rev: 3.AA
# Jan 8 19:51:57 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 05
# Jan 8 19:51:57 user.warn kernel: Vendor: ATA Model: ST3500630AS Rev: 3.AA
# Jan 8 19:51:57 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 05
# Jan 8 19:51:57 user.warn kernel: Vendor: ATA Model: ST3500630AS Rev: 3.AA
# Jan 8 19:51:57 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 05
# Jan 8 19:51:57 user.warn kernel: Vendor: ATA Model: ST3500630AS Rev: 3.AA
# Jan 8 19:51:57 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 05
# Jan 8 19:51:57 user.warn kernel: Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
# Jan 8 19:51:57 user.warn kernel: Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
# Jan 8 19:51:57 user.warn kernel: Attached scsi disk sdc at scsi3, channel 0, id 0, lun 0
# Jan 8 19:51:57 user.warn kernel: Attached scsi disk sdd at scsi4, channel 0, id 0, lun 0
# Jan 8 19:51:57 user.warn kernel: SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
# Jan 8 19:51:57 user.info kernel: Partition check:
# Jan 8 19:51:57 user.info kernel: /dev/scsi/host1/bus0/target0/lun0: p1
# Jan 8 19:51:57 user.warn kernel: SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
# Jan 8 19:51:57 user.info kernel: /dev/scsi/host2/bus0/target0/lun0: p1
# Jan 8 19:51:57 user.warn kernel: SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB)
# Jan 8 19:51:57 user.info kernel: /dev/scsi/host3/bus0/target0/lun0: p1
# Jan 8 19:51:57 user.warn kernel: SCSI device sdd: 976773168 512-byte hdwr sectors (500108 MB)
# Jan 8 19:51:57 user.info kernel: /dev/scsi/host4/bus0/target0/lun0: p1
# Jan 8 19:51:57 user.info kernel: raw1394: /dev/raw1394 device initialized
# Jan 8 19:51:57 user.info kernel: sbp2: $Rev: 1074 $ Ben Collins
# Jan 8 19:51:57 user.err kernel: ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
# Jan 8 19:51:57 user.info kernel: usb.c: registered new driver usbdevfs
# Jan 8 19:51:57 user.info kernel: usb.c: registered new driver hub
# Jan 8 19:51:57 user.info kernel: host/uhci.c: USB Universal Host Controller Interface driver v1.1
# Jan 8 19:51:57 user.info kernel: usb.c: registered new driver usbkbd
# Jan 8 19:51:57 user.info kernel: usbkbd.c: :USB HID Boot Protocol keyboard driver
# Jan 8 19:51:57 user.info kernel: Initializing USB Mass Storage driver.
# Jan 8 19:51:57 user.info kernel: usb.c: registered new driver usb-storage
# Jan 8 19:51:57 user.info kernel: USB Mass Storage support registered.
# Jan 8 19:51:57 user.info kernel: NET4: Linux TCP/IP 1.0 for NET4.0
# Jan 8 19:51:57 user.info kernel: IP Protocols: ICMP, UDP, TCP
# Jan 8 19:51:57 user.info kernel: IP: routing cache hash table of 8192 buckets, 64Kbytes
# Jan 8 19:51:57 user.info kernel: TCP: Hash tables configured (established 262144 bind 65536)
# Jan 8 19:51:57 user.info kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
# Jan 8 19:51:57 user.notice kernel: RAMDISK: NASLite file system found at block 0
# Jan 8 19:51:57 user.warn kernel: .<6>Freeing initrd memory: 1952k freed
# Jan 8 19:51:57 user.warn kernel: VFS: Mounted root (ext2 filesystem).
# Jan 8 19:51:57 user.info kernel: Mounted devfs on /dev
# Jan 8 19:51:57 user.info kernel: Freeing unused kernel memory: 540k freed
# Jan 8 19:51:57 user.info kernel: tg3: eth0: Link is up at 1000 Mbps, full duplex.
# Jan 8 19:51:57 user.info kernel: tg3: eth0: Flow control is on for TX and on for RX.
# Jan 8 19:51:57 user.info kernel: kjournald starting. Commit interval 5 seconds
# Jan 8 19:51:57 user.info kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
# Jan 8 19:51:57 user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
# Jan 8 19:51:57 user.info kernel: kjournald starting. Commit interval 5 seconds
# Jan 8 19:51:57 user.info kernel:
# Jan 8 19:51:57 user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
# Jan 8 19:51:57 user.info kernel: kjournald starting. Commit interval 5 seconds
# Jan 8 19:51:57 user.info kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,33), internal journal
# Jan 8 19:51:57 user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
# Jan 8 19:51:57 user.info kernel: kjournald starting. Commit interval 5 seconds
# Jan 8 19:51:57 user.info kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,49), internal journal
# Jan 8 19:51:57 user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.

It appears you have too many IRQ allocations and some devices end up sharing IRQs. In the BIOS disable everything you don't need such as audio, lpt, com, etc. Reset the BIOS to force resource reallocation and try again.

Tony,

I have turned off all non-required items.

The only PCI devices still seen are
IDE controller
Internal VGA - IRQ 11
Internal GB ethernet (Broadcom 5782) - IRQ 5
Promise SATA300 TX4 4PORT - IRQ 10

I am still having same errors during large (200GB) RSync transfer.
I have moved the Promise Card through all 3 PCI solts

Do you have any other ideas to try.

I appreciate your help
Carson

Hm!

Try turning SMART off for the problem drives in the admin, reboot and try again.

Tony,

I turned off SMART on all 4 drives and the copies are now successful.

Can you explain why SMART would have caused my SCSI sense errors?

Also can you take a quick look at my SYSLOG and see if everything else looks good. I am concerned that my Intel Pro 1000 MT card does not show a IRQ under network status - device details section. The NetGear GA311 did. I switched to the Intel and improved performance during my exhaustive testing to eliminate this SCSI sense error.

Thanks
Carson

SYSLOG below


* Jan 24 01:16:32 user.notice kernel: klogd started: BusyBox v1.01 (2007.03.15-22:03+0000)
* Jan 24 01:16:32 user.warn kernel: Linux version 2.4.35.NASLite (root@tzt) (gcc version 3.4.6) #2 Sun Aug 12 09:03:16 EDT 2007
* Jan 24 01:16:32 user.info kernel: BIOS-provided physical RAM map:
* Jan 24 01:16:32 user.warn kernel: BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
* Jan 24 01:16:32 user.warn kernel: BIOS-e820: 000000000009d400 - 00000000000a0000 (reserved)
* Jan 24 01:16:32 user.warn kernel: BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
* Jan 24 01:16:32 user.warn kernel: BIOS-e820: 0000000000100000 - 000000003f7f0000 (usable)
* Jan 24 01:16:32 user.warn kernel: BIOS-e820: 000000003f7f0000 - 0000000040000000 (reserved)
* Jan 24 01:16:32 user.warn kernel: BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
* Jan 24 01:16:32 user.notice kernel: 119MB HIGHMEM available.
* Jan 24 01:16:32 user.notice kernel: 896MB LOWMEM available.
* Jan 24 01:16:32 user.warn kernel: On node 0 totalpages: 260080
* Jan 24 01:16:32 user.warn kernel: zone(0): 4096 pages.
* Jan 24 01:16:32 user.warn kernel: zone(1): 225280 pages.
* Jan 24 01:16:32 user.warn kernel: zone(2): 30704 pages.
* Jan 24 01:16:32 user.info kernel: ACPI: RSDP (v000 COMPAQ ) @ 0x000e9e10
* Jan 24 01:16:32 user.info kernel: ACPI: RSDT (v001 COMPAQ CPQ0064 0x20040810 0x00000000) @ 0x000e5640
* Jan 24 01:16:32 user.info kernel: ACPI: FADT (v001 COMPAQ SPRINGD 0x00000001 0x00000000) @ 0x000e56f8
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ PROJECT 0x00000001 MSFT 0x0100000e) @ 0x000e6585
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ CORE_PNP 0x00000001 MSFT 0x0100000e) @ 0x000e6c0a
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ CORE_UTL 0x00000001 MSFT 0x0100000e) @ 0x000e7156
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ VILLTBL1 0x00000001 MSFT 0x0100000e) @ 0x000e7348
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ LGCYLITE 0x00000001 MSFT 0x0100000e) @ 0x000e7676
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ UART2 0x00000001 MSFT 0x0100000e) @ 0x000e7bb5
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ FLOPPY 0x00000001 MSFT 0x0100000e) @ 0x000e7d1c
* Jan 24 01:16:32 user.info kernel: ACPI: MADT (v001 COMPAQ SPRINGD 0x00000001 0x00000000) @ 0x000e576c
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ APIC 0x00000001 MSFT 0x0100000e) @ 0x000e9b2c
* Jan 24 01:16:32 user.info kernel: ACPI: ASF! (v016 COMPAQ SPRINGD 0x00000001 0x00000000) @ 0x000e57d4
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ PNP_PRSS 0x00000001 MSFT 0x0100000e) @ 0x000e82d8
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ UR2_PRSS 0x00000001 MSFT 0x0100000e) @ 0x000e86e7
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ FPY_PRSS 0x00000001 MSFT 0x0100000e) @ 0x000e8854
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ S1 0x00000001 MSFT 0x0100000e) @ 0x000e896d
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ CORE_S3 0x00000001 MSFT 0x0100000e) @ 0x000e8b89
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ PIDETM 0x00000001 MSFT 0x0100000e) @ 0x000e8c66
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ GTF0 0x00000001 MSFT 0x0100000e) @ 0x000e9200
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ L08 0x00000001 MSFT 0x0100000e) @ 0x000e98e3
* Jan 24 01:16:32 user.info kernel: ACPI: SSDT (v001 COMPAQ FINIS 0x00000001 MSFT 0x0100000e) @ 0x000e9d30
* Jan 24 01:16:32 user.info kernel: ACPI: DSDT (v001 COMPAQ DSDT 0x00000001 MSFT 0x0100000e) @ 0x00000000
* Jan 24 01:16:32 user.warn kernel: Kernel command line: rw root=/dev/ram0 initrd=NASLite.02 quiet BOOT_IMAGE=NASLite.01
* Jan 24 01:16:32 user.info kernel: Initializing CPU#0
* Jan 24 01:16:32 user.warn kernel: Detected 2992.591 MHz processor.
* Jan 24 01:16:32 user.warn kernel: Console: colour VGA+ 80x25
* Jan 24 01:16:32 user.warn kernel: Calibrating delay loop. 5976.88 BogoMIPS
* Jan 24 01:16:32 user.info kernel: Memory: 1022072k/1040320k available (2214k kernel code, 17852k reserved, 642k data, 540k init, 122816k highmem)
* Jan 24 01:16:32 user.info kernel: Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
* Jan 24 01:16:32 user.info kernel: Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
* Jan 24 01:16:32 user.info kernel: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
* Jan 24 01:16:32 user.info kernel: Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
* Jan 24 01:16:32 user.warn kernel: Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
* Jan 24 01:16:32 user.info kernel: CPU: Trace cache: 12K uops, L1 D cache: 16K
* Jan 24 01:16:32 user.info kernel: CPU: L2 cache: 1024K
* Jan 24 01:16:32 user.debug kernel: CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
* Jan 24 01:16:32 user.debug kernel: CPU: Common caps: bfebfbff 00000000 00000000 00000000
* Jan 24 01:16:32 user.warn kernel: CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04
* Jan 24 01:16:32 user.info kernel: Enabling fast FPU save and restore. done.
* Jan 24 01:16:32 user.info kernel: Enabling unmasked SIMD FPU exception support. done.
* Jan 24 01:16:32 user.info kernel: Checking 'hlt' instruction. OK.
* Jan 24 01:16:32 user.warn kernel: ACPI: IRQ9 SCI: Edge set to Level Trigger.
* Jan 24 01:16:32 user.warn kernel: POSIX conformance testing by UNIFIX
* Jan 24 01:16:32 user.warn kernel: mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
* Jan 24 01:16:32 user.warn kernel: mtrr: detected mtrr type: Intel
* Jan 24 01:16:32 user.info kernel: ACPI: Subsystem revision 20040326
* Jan 24 01:16:32 user.info kernel: PCI: PCI BIOS revision 2.20 entry at 0xec1a9, last bus=5
* Jan 24 01:16:32 user.info kernel: PCI: Using configuration type 1
* Jan 24 01:16:32 user.info kernel: ACPI: Interpreter enabled
* Jan 24 01:16:32 user.info kernel: ACPI: Using PIC for interrupt routing
* Jan 24 01:16:32 user.info kernel: ACPI: System [ACPI] (supports S0 S1 S4 S5)
* Jan 24 01:16:32 user.warn kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15)
* Jan 24 01:16:32 user.warn kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
* Jan 24 01:16:32 user.warn kernel: (IRQs 3 4 5 6 7 *10 11 14 15)
* Jan 24 01:16:32 user.warn kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 14 15)
* Jan 24 01:16:32 user.warn kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
* Jan 24 01:16:32 user.warn kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 14 15)
* Jan 24 01:16:32 user.warn kernel: ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
* Jan 24 01:16:32 user.warn kernel: ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 14 15)
* Jan 24 01:16:32 user.info kernel: ACPI: PCI Root Bridge [PCI0] (00:00)
* Jan 24 01:16:32 user.warn kernel: PCI: Probing PCI hardware (bus 00)
* Jan 24 01:16:32 user.info kernel: PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
* Jan 24 01:16:32 user.warn kernel: Transparent bridge - PCI device 8086:244e
* Jan 24 01:16:32 user.debug kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
* Jan 24 01:16:32 user.debug kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
* Jan 24 01:16:32 user.info kernel: PCI: Probing PCI hardware
* Jan 24 01:16:32 user.warn kernel: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
* Jan 24 01:16:32 user.warn kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
* Jan 24 01:16:32 user.warn kernel: ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
* Jan 24 01:16:32 user.info kernel: PCI: Using ACPI for IRQ routing
* Jan 24 01:16:32 user.info kernel: Linux NET4.0 for Linux 2.4
* Jan 24 01:16:32 user.info kernel: Based upon Swansea University Computer Society NET3.039
* Jan 24 01:16:32 user.warn kernel: Initializing RT netlink socket
* Jan 24 01:16:32 user.warn kernel: Starting kswapd
* Jan 24 01:16:32 user.warn kernel: allocated 32 pages and 32 bhs reserved for the highmem bounces
* Jan 24 01:16:32 user.info kernel: Journalled Block Device driver loaded
* Jan 24 01:16:32 user.info kernel: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
* Jan 24 01:16:32 user.info kernel: devfs: boot_options: 0x1
* Jan 24 01:16:32 user.info kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
* Jan 24 01:16:32 user.info kernel: ACPI: Power Button (FF) [PWRF]
* Jan 24 01:16:32 user.info kernel: ACPI: Processor [CPU0] (supports C1, 8 throttling states)
* Jan 24 01:16:32 user.info kernel: ACPI: Processor [CPU1] (supports C1, 8 throttling states)
* Jan 24 01:16:32 user.warn kernel: pty: 256 Unix98 ptys configured
* Jan 24 01:16:32 user.info kernel: Real Time Clock Driver v1.10f
* Jan 24 01:16:32 user.info kernel: Floppy drive(s): fd0 is 1.44M
* Jan 24 01:16:32 user.info kernel: FDC 0 is a post-1991 82077
* Jan 24 01:16:32 user.warn kernel: RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
* Jan 24 01:16:32 user.info kernel: loop: loaded (max 8 devices)
* Jan 24 01:16:32 user.info kernel: Intel(R) PRO/1000 Network Driver - version 7.3.20-k4
* Jan 24 01:16:32 user.info kernel: Copyright (c) 1999-2006 Intel Corporation.
* Jan 24 01:16:32 user.info kernel: e1000: 05:0a.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:17:2e:87
* Jan 24 01:16:32 user.info kernel: e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
* Jan 24 01:16:32 user.info kernel: dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15
* Jan 24 01:16:32 user.warn kernel: FW Version=$Version$
* Jan 24 01:16:32 user.info kernel: pcnet32.c:v1.30h 06.24.2004 tsbogend@alpha.franken.de
* Jan 24 01:16:32 user.info kernel: ThunderLAN driver v1.15
* Jan 24 01:16:32 user.info kernel: TLAN: 0 devices installed, PCI: 0 EISA: 0
* Jan 24 01:16:32 user.info kernel: dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
* Jan 24 01:16:32 user.info kernel: ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
* Jan 24 01:16:32 user.warn kernel: sk98lin: No adapter found.
* Jan 24 01:16:32 user.info kernel: forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.50.
* Jan 24 01:16:32 user.info kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
* Jan 24 01:16:32 user.info kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
* Jan 24 01:16:32 user.info kernel: ICH5: IDE controller at PCI slot 00:1f.1
* Jan 24 01:16:32 user.warn kernel: PCI: Enabling device 00:1f.1 (0005 -> 0007)
* Jan 24 01:16:32 user.info kernel: ICH5: chipset revision 2
* Jan 24 01:16:32 user.info kernel: ICH5: not 100% native mode: will probe irqs later
* Jan 24 01:16:32 user.info kernel: ide0: BM-DMA at 0x2080-0x2087, BIOS settings: hda:DMA, hdb:pio
* Jan 24 01:16:32 user.warn kernel: hda: HL-DT-ST RW/DVD GCC-4481B, ATAPI CD/DVD-ROM drive
* Jan 24 01:16:32 user.warn kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
* Jan 24 01:16:32 user.info kernel: SCSI subsystem driver Revision: 1.00
* Jan 24 01:16:32 user.info kernel: Loading Adaptec I2O RAID: Version 2.4 Build 5
* Jan 24 01:16:32 user.info kernel: Detecting Adaptec I2O RAID controllers.
* Jan 24 01:16:32 user.info kernel: Red Hat/Adaptec aacraid driver (1.1-3 Aug 12 2007 09:05:44)
* Jan 24 01:16:32 user.warn kernel: scsi: Detection failed (no card)
* Jan 24 01:16:32 user.notice kernel: megaraid: v2.10.10.1 (Release Date: Thu Jan 27 16:19:44 EDT 2005)
* Jan 24 01:16:32 user.warn kernel: GDT-HA: Storage RAID Controller Driver. Version: 3.04
* Jan 24 01:16:32 user.warn kernel: GDT-HA: Found 0 PCI Storage RAID Controllers
* Jan 24 01:16:32 user.warn kernel: 3ware Storage Controller device driver for Linux v1.02.00.037.
* Jan 24 01:16:32 user.warn kernel: 3w-xxxx: No cards found.
* Jan 24 01:16:32 user.debug kernel: libata version 1.20 loaded.
* Jan 24 01:16:32 user.debug kernel: PCI(00:1f.2): version 1.05
* Jan 24 01:16:32 user.debug kernel: PCI: Setting latency timer of device 00:1f.2 to 64
* Jan 24 01:16:32 user.info kernel: ata1: SATA max UDMA/133 cmd 0x20B8 ctl 0x20D2 bmdma 0x2090 irq 10
* Jan 24 01:16:32 user.info kernel: ata2: SATA max UDMA/133 cmd 0x20C0 ctl 0x20D6 bmdma 0x2098 irq 10
* Jan 24 01:16:32 user.info kernel: ata1: SATA port has no device.
* Jan 24 01:16:32 user.info kernel: ata2: SATA port has no device.
* Jan 24 01:16:32 user.info kernel: scsi1 : ata_piix
* Jan 24 01:16:32 user.info kernel: scsi2 : ata_piix
* Jan 24 01:16:32 user.debug kernel: PCI(05:09.0): version 1.03
* Jan 24 01:16:32 user.info kernel: ata3: SATA max UDMA/133 cmd 0xF8821200 ctl 0xF8821238 bmdma 0x0 irq 10
* Jan 24 01:16:32 user.info kernel: ata4: SATA max UDMA/133 cmd 0xF8821280 ctl 0xF88212B8 bmdma 0x0 irq 10
* Jan 24 01:16:32 user.info kernel: ata5: SATA max UDMA/133 cmd 0xF8821300 ctl 0xF8821338 bmdma 0x0 irq 10
* Jan 24 01:16:32 user.info kernel: ata6: SATA max UDMA/133 cmd 0xF8821380 ctl 0xF88213B8 bmdma 0x0 irq 10
* Jan 24 01:16:32 user.debug kernel: cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
* Jan 24 01:16:32 user.info kernel: ata3: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
* Jan 24 01:16:32 user.info kernel: ata3: dev 0 configured for UDMA/133
* Jan 24 01:16:32 user.debug kernel: ata4: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
* Jan 24 01:16:32 user.info kernel: ata4: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
* Jan 24 01:16:32 user.info kernel: ata4: dev 0 configured for UDMA/133
* Jan 24 01:16:32 user.debug kernel: ata5: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
* Jan 24 01:16:32 user.info kernel: ata5: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
* Jan 24 01:16:32 user.info kernel: ata5: dev 0 configured for UDMA/133
* Jan 24 01:16:32 user.debug kernel: ata6: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
* Jan 24 01:16:32 user.info kernel: ata6: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
* Jan 24 01:16:32 user.info kernel: ata6: dev 0 configured for UDMA/133
* Jan 24 01:16:32 user.info kernel: scsi3 : sata_promise
* Jan 24 01:16:32 user.info kernel: scsi4 : sata_promise
* Jan 24 01:16:32 user.info kernel: scsi5 : sata_promise
* Jan 24 01:16:32 user.info kernel: scsi6 : sata_promise
* Jan 24 01:16:32 user.warn kernel: Vendor: ATA Model: ST3500630AS Rev: 3.AA
* Jan 24 01:16:32 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 05
* Jan 24 01:16:32 user.warn kernel: Vendor: ATA Model: ST3500630AS Rev: 3.AA
* Jan 24 01:16:32 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 05
* Jan 24 01:16:32 user.warn kernel: Vendor: ATA Model: ST3500630AS Rev: 3.AA
* Jan 24 01:16:32 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 05
* Jan 24 01:16:32 user.warn kernel: Vendor: ATA Model: ST3500630AS Rev: 3.AA
* Jan 24 01:16:32 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 05
* Jan 24 01:16:32 user.warn kernel: Attached scsi disk sda at scsi3, channel 0, id 0, lun 0
* Jan 24 01:16:32 user.warn kernel: Attached scsi disk sdb at scsi4, channel 0, id 0, lun 0
* Jan 24 01:16:32 user.warn kernel: Attached scsi disk sdc at scsi5, channel 0, id 0, lun 0
* Jan 24 01:16:32 user.warn kernel: Attached scsi disk sdd at scsi6, channel 0, id 0, lun 0
* Jan 24 01:16:32 user.warn kernel: SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
* Jan 24 01:16:32 user.info kernel: Partition check:
* Jan 24 01:16:32 user.info kernel: /dev/scsi/host3/bus0/target0/lun0: p1
* Jan 24 01:16:32 user.warn kernel: SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
* Jan 24 01:16:32 user.info kernel: /dev/scsi/host4/bus0/target0/lun0: p1
* Jan 24 01:16:32 user.warn kernel: SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB)
* Jan 24 01:16:32 user.info kernel: /dev/scsi/host5/bus0/target0/lun0: p1
* Jan 24 01:16:32 user.warn kernel: SCSI device sdd: 976773168 512-byte hdwr sectors (500108 MB)
* Jan 24 01:16:32 user.info kernel: /dev/scsi/host6/bus0/target0/lun0: p1
* Jan 24 01:16:32 user.info kernel: raw1394: /dev/raw1394 device initialized
* Jan 24 01:16:32 user.info kernel: sbp2: $Rev: 1074 $ Ben Collins
* Jan 24 01:16:32 user.err kernel: ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
* Jan 24 01:16:32 user.info kernel: usb.c: registered new driver usbdevfs
* Jan 24 01:16:32 user.info kernel: usb.c: registered new driver hub
* Jan 24 01:16:32 user.info kernel: host/uhci.c: USB Universal Host Controller Interface driver v1.1
* Jan 24 01:16:32 user.info kernel: usb.c: registered new driver usbkbd
* Jan 24 01:16:32 user.info kernel: usbkbd.c: :USB HID Boot Protocol keyboard driver
* Jan 24 01:16:32 user.info kernel: Initializing USB Mass Storage driver.
* Jan 24 01:16:32 user.info kernel: usb.c: registered new driver usb-storage
* Jan 24 01:16:32 user.info kernel: USB Mass Storage support registered.
* Jan 24 01:16:32 user.info kernel: NET4: Linux TCP/IP 1.0 for NET4.0
* Jan 24 01:16:32 user.info kernel: IP Protocols: ICMP, UDP, TCP
* Jan 24 01:16:32 user.info kernel: IP: routing cache hash table of 8192 buckets, 64Kbytes
* Jan 24 01:16:32 user.info kernel: TCP: Hash tables configured (established 262144 bind 65536)
* Jan 24 01:16:32 user.info kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
* Jan 24 01:16:32 user.notice kernel: RAMDISK: NASLite file system found at block 0
* Jan 24 01:16:32 user.warn kernel: .<6>Freeing initrd memory: 1952k freed
* Jan 24 01:16:32 user.warn kernel: VFS: Mounted root (ext2 filesystem).
* Jan 24 01:16:32 user.info kernel: Mounted devfs on /dev
* Jan 24 01:16:32 user.info kernel: Freeing unused kernel memory: 540k freed
* Jan 24 01:16:32 user.info kernel: e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
* Jan 24 01:16:32 user.info kernel: kjournald starting. Commit interval 5 seconds
* Jan 24 01:16:32 user.info kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
* Jan 24 01:16:32 user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
* Jan 24 01:16:32 user.info kernel: kjournald starting. Commit interval 5 seconds
* Jan 24 01:16:32 user.info kernel: rnal journal
* Jan 24 01:16:32 user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
* Jan 24 01:16:32 user.info kernel: kjournald starting. Commit interval 5 seconds
* Jan 24 01:16:32 user.info kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,33), internal journal
* Jan 24 01:16:32 user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
* Jan 24 01:16:32 user.info kernel: kjournald starting. Commit interval 5 seconds
* Jan 24 01:16:32 user.info kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,49), internal journal
* Jan 24 01:16:32 user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.

In some rare instances it is possible for the SMART probe, a controller and/or its firmware, a drive and/or it's firmware, or any combination of those to introduce incompatibilities that subsequently result in an error. You may check the controller and/or the PC BIOS and enable or disable SMART if the option is available. Then try running NASLite with the SMART probe turned on once again. It is possible that the BIOS places the drive in a state that the NASLite SMART probe does not expect to see, or some other silly condition that is tripping the process.

Anyway, it appears that you have narrowed the problem down to a manageable set of possibilities.