Hello all
My Naslite has been up for 50 days.. but when I went to look at the details.. I have had some errors.. I think it means one of my hard drives is on the way out.. can someone please assist me with this.
PRODUCT NASLite-2 Operating System Type
VERSION v2.61 12-2009 Operating System Version
Feb 25 22:39:29 [5] hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
Feb 25 22:39:29 [5] hdb: dma_intr: error=0x40 { UncorrectableError }, LBAsect=952310, sector=952209
Feb 25 22:39:29 [5] hdb: possibly failed opcode: 0x25
Feb 25 22:39:29 [5] end_request: I/O error, dev hdb, sector 952209
Feb 25 22:39:31 [5] hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
Feb 25 22:39:31 [5] hdb: dma_intr: error=0x40 { UncorrectableError }, LBAsect=952310, sector=952217
Feb 25 22:39:31 [5] hdb: possibly failed opcode: 0x25
MODEL: MDT MD2500BB-00DWA0, SN# MDT-MMAEH2466643, v.15.05R15
INTERFACE: DEVICE-HDB
Server Storage Disk-1
General:
This page provides specific information pertaining to Disk-1. Hardware, filesystem and S.M.A.R.T. details are listed below.
Disk-1 Hardware Details:
MODEL: MDT MD2500BB-00DWA0, SN# MDT-MMAEH2466643, v.15.05R15
INTERFACE: DEVICE-HDB
Filesystem Details:
tune2fs 1.40.4 (31-Dec-2007)
Filesystem volume name: NASLite-SE000101
Last mounted on:
Filesystem UUID: 412e8745-0ff7-4150-9c49-4b0885085452
Filesystem magic number: 0xEF53
Filesystem revision #: 1 (dynamic)
Filesystem features: has_journal filetype needs_recovery sparse_super
Filesystem flags: signed directory hash
Default mount options: (none)
Filesystem state: clean
Errors behavior: Continue
Filesystem OS type: Linux
Inode count: 30539776
Block count: 61049008
Reserved block count: 0
Free blocks: 7380598
Free inodes: 30499729
First block: 0
Block size: 4096
Fragment size: 4096
Blocks per group: 32768
Fragments per group: 32768
Inodes per group: 16384
Inode blocks per group: 512
Last mount time: Sun Jan 10 18:09:49 2010
Last write time: Sun Jan 10 18:09:49 2010
Mount count: 3
Maximum mount count: 21
Last checked: Sun Jan 10 17:26:10 2010
Check interval: 15552000 (6 months)
Next check after: Fri Jul 9 17:26:10 2010
Reserved blocks uid: 0 (user admin)
Reserved blocks gid: 0 (group admin)
First inode: 11
Inode size: 128
Journal inode: 8
Journal backup: inode blocks
S.M.A.R.T. Status:
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is
http://smartmontools.sourceforge.net/=== START OF INFORMATION SECTION ===
Device Model: MDT MD2500BB-00DWA0
Serial Number: MDT-MMAEH2466643
Firmware Version: 15.05R15
User Capacity: 250,059,350,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon Mar 1 21:24:01 2010 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (7599) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 95) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 200 001 051 Pre-fail Always In_the_past 0
3 Spin_Up_Time 0x0007 137 112 021 Pre-fail Always - 3650
4 Start_Stop_Count 0x0032 100 100 040 Old_age Always - 373
5 Reallocated_Sector_Ct 0x0033 199 199 140 Pre-fail Always - 4
7 Seek_Error_Rate 0x000b 100 253 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 060 060 000 Old_age Always - 29745
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 372
194 Temperature_Celsius 0x0022 112 253 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 196 196 000 Old_age Always - 4
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 9
198 Offline_Uncorrectable 0x0012 200 200 000 Old_age Always - 16
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 200 155 051 Pre-fail Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 65535 inconsistent with error log pointer 2
ATA Error Count: 65535 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 65535 occurred at disk power-on lifetime: 159 hours (6 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 55 8f 0e f0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
01 00 25 00 00 08 00 00 46d+05:45:33.150 [RESERVED]
01 00 25 00 00 08 00 00 46d+05:45:33.150 [RESERVED]
00 00 0e 00 00 51 8f 00 46d+05:45:33.150 NOP [Abort queued commands]
01 00 25 00 00 08 00 00 46d+05:45:33.150 [RESERVED]
00 00 0e 00 00 51 8f 00 46d+05:45:33.150 NOP [Abort queued commands]
Error 65534 occurred at disk power-on lifetime: 159 hours (6 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 55 8f 0e f0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
01 00 25 00 00 08 00 00 46d+05:45:31.200 [RESERVED]
01 00 25 00 00 08 00 00 46d+05:45:31.200 [RESERVED]
00 00 0e 00 00 51 8f 00 46d+05:45:31.200 NOP [Abort queued commands]
01 00 25 00 00 08 00 00 46d+05:45:31.200 [RESERVED]
00 00 0e 00 00 51 8f 00 46d+05:45:31.200 NOP [Abort queued commands]
Error 65533 occurred at disk power-on lifetime: 159 hours (6 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 55 8f 0e f0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
01 00 25 00 00 08 00 00 46d+05:45:29.300 [RESERVED]
00 00 0e 00 00 51 8f 00 46d+05:45:29.300 NOP [Abort queued commands]
01 00 25 00 00 08 00 00 46d+05:45:29.300 [RESERVED]
00 00 0e 00 00 51 8f 00 46d+05:45:29.300 NOP [Abort queued commands]
01 00 25 00 00 08 00 00 46d+05:45:29.300 [RESERVED]
Error 65532 occurred at disk power-on lifetime: 159 hours (6 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 55 8f 0e f0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
01 00 25 00 00 08 00 00 46d+05:45:27.350 [RESERVED]
00 00 0e 00 00 51 8f 00 46d+05:45:27.350 NOP [Abort queued commands]
01 00 25 00 00 08 00 00 46d+05:45:27.350 [RESERVED]
00 00 0e 00 00 51 8f 00 46d+05:45:27.350 NOP [Abort queued commands]
01 00 25 00 00 08 00 00 46d+05:45:27.350 [RESERVED]
Error 65531 occurred at disk power-on lifetime: 159 hours (6 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 55 8f 0e f0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
01 00 25 00 00 08 00 00 46d+05:45:25.450 [RESERVED]
00 00 0e 00 00 51 8f 00 46d+05:45:25.450 NOP [Abort queued commands]
01 00 25 00 00 08 00 00 46d+05:45:25.450 [RESERVED]
00 00 0e 00 00 51 8f 00 46d+05:45:25.450 NOP [Abort queued commands]
01 00 25 00 00 08 00 00 46d+05:45:25.450 [RESERVED]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 732 283309350
# 2 Extended offline Completed: read failure 90% 732 283309350
# 3 Extended offline Completed: read failure 90% 35 283309350
# 4 Extended offline Completed: read failure 90% 35 283309350
# 5 Extended offline Completed: read failure 50% 431 193707529
# 6 Extended offline Completed: read failure 50% 588 193707529
# 7 Extended offline Completed: read failure 50% 280 193707529
# 8 Extended offline Completed: read failure 50% 891 193707529
# 9 Extended offline Completed: read failure 50% 888 193707529
#10 Extended offline Completed: read failure 20% 451 193707529
#11 Extended offline Interrupted (host reset) 90% 450 -
#12 Extended offline Interrupted (host reset) 90% 450 -
#13 Extended offline Completed: read failure 50% 256 193707529
#14 Extended offline Completed: read failure 50% 180 193707529
#15 Extended offline Completed without error 00% 1029 -
#16 Extended offline Completed without error 00% 913 -
#17 Extended offline Completed without error 00% 897 -
#18 Extended offline Completed without error 00% 895 -
#19 Extended offline Completed without error 00% 1052 -
#20 Extended offline Completed without error 00% 741 -
#21 Extended offline Completed without error 00% 671 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.