Hi, I've just installed NASLite-2 and wow just like to say how nice and easy was it it set up
I am a real newbie at all this but have tried to read up as much possible.
I've installed NASLite-2 on a reasonably high spec system but the data transfer speed seems really really slow.
In fact I am getting less than 750kbs when transfering files from my high spec pc.
The way I'm transfering to the NAS is from a Windows 7 64bit pc using a 'mapped drive' I've set up in 'my computer'
The NAS spec is Athlon 2000+ 512mb Ram. 1xATA 133 HDD and 1xSATA HDD.
Both the NAS and my pc have identical Realtek RTL8169 gigabit PCI nic's.
I have a BT Business Router which is attached to a 10/100 Netgear Switch which then connects the NAS and the PC.
If I ping the NAS from the PC it is less than <1ms
Can anyone suggest anything I can do to find the cause of the slow file transfer speed please?
Thanks
Steve
PS: I've posted the following hoping it might help:
eth0: Identified chip type is 'RTL8169'.
eth0: RTL8169 at 0xe0808000, 00:06:4f:80:96:b7, IRQ 16
eth0: Auto-negotiation Enabled.
eth0: 100Mbps Full-duplex operation.
eth0 Link encap:Ethernet HWaddr 00:06:4F:80:96:B7
inet addr:192.168.1.65 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:240612 errors:0 dropped:0 overruns:0 frame:0
TX packets:147298 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:302378943 (288.3 MiB) TX bytes:12906596 (12.3 MiB)
Interrupt:16 Base address:0x8000
Oct 28 15:30:05 [3] klogd started: BusyBox v1.01 (2007.03.15-22:03+0000)
Oct 28 15:30:05 [4] Linux version 2.4.37.NASLite (root@tzt) (gcc version 3.4.6) #1 Tue Dec 9 22:04:52 EST 2008
Oct 28 15:30:05 [2] BIOS-provided physical RAM map:
Oct 28 15:30:05 [4] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
Oct 28 15:30:05 [4] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
Oct 28 15:30:05 [4] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Oct 28 15:30:05 [4] BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
Oct 28 15:30:05 [4] BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
Oct 28 15:30:05 [4] BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
Oct 28 15:30:05 [4] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
Oct 28 15:30:05 [4] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
Oct 28 15:30:05 [4] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Oct 28 15:30:05 [3] 0MB HIGHMEM available.
Oct 28 15:30:05 [3] 511MB LOWMEM available.
Oct 28 15:30:05 [4] On node 0 totalpages: 131056
Oct 28 15:30:05 [4] zone(0): 4096 pages.
Oct 28 15:30:05 [4] zone(1): 126960 pages.
Oct 28 15:30:05 [4] zone(2): 0 pages.
Oct 28 15:30:05 [2] ACPI: RSDP (v000 Nvidia ) @ 0x000f6d50
Oct 28 15:30:05 [2] ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
Oct 28 15:30:05 [2] ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
Oct 28 15:30:05 [2] ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff7580
Oct 28 15:30:05 [2] ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
Oct 28 15:30:05 [2] ACPI: Local APIC address 0xfee00000
Oct 28 15:30:05 [2] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Oct 28 15:30:05 [4] Processor #0 Pentium(tm) Pro APIC version 16
Oct 28 15:30:05 [2] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
Oct 28 15:30:05 [2] ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
Oct 28 15:30:05 [2] IOAPIC[0]: Assigned apic_id 2
Oct 28 15:30:05 [4] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, IRQ 0-23
Oct 28 15:30:05 [2] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Oct 28 15:30:05 [4] ACPI: BIOS IRQ0 pin2 override ignored.
Oct 28 15:30:05 [2] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Oct 28 15:30:05 [2] Using ACPI (MADT) for SMP configuration information
Oct 28 15:30:05 [4] Kernel command line: rw root=/dev/ram0 initrd=NASLite.02 quiet BOOT_IMAGE=NASLite.01
Oct 28 15:30:05 [2] Initializing CPU#0
Oct 28 15:30:05 [4] Detected 1664.161 MHz processor.
Oct 28 15:30:05 [4] Console: colour VGA+ 80x25
Oct 28 15:30:05 [4] Calibrating delay loop. 3322.67 BogoMIPS
Oct 28 15:30:05 [2] Memory: 511852k/524224k available (2326k kernel code, 11984k reserved, 684k data, 560k init, 0k highmem)
Oct 28 15:30:05 [2] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Oct 28 15:30:05 [2] Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Oct 28 15:30:05 [2] Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Oct 28 15:30:05 [2] Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Oct 28 15:30:05 [4] Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
Oct 28 15:30:05 [2] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Oct 28 15:30:05 [2] CPU: L2 Cache: 256K (64 bytes/line)
Oct 28 15:30:05 [2] Intel machine check architecture supported.
Oct 28 15:30:05 [2] Intel machine check reporting enabled on CPU#0.
Oct 28 15:30:05 [1] CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
Oct 28 15:30:05 [1] CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
Oct 28 15:30:05 [4] CPU: AMD Athlon(tm) XP 2000+ stepping 02
Oct 28 15:30:05 [2] Enabling fast FPU save and restore. done.
Oct 28 15:30:05 [2] Enabling unmasked SIMD FPU exception support. done.
Oct 28 15:30:05 [2] Checking 'hlt' instruction. OK.
Oct 28 15:30:05 [4] POSIX conformance testing by UNIFIX
Oct 28 15:30:05 [4] enabled ExtINT on CPU#0
Oct 28 15:30:05 [4] ESR value before enabling vector: 00000000
Oct 28 15:30:05 [4] ESR value after enabling vector: 00000000
Oct 28 15:30:05 [4] ENABLING IO-APIC IRQs
Oct 28 15:30:05 [1] init IO_APIC IRQs
Oct 28 15:30:05 [1] IO-APIC (apicid-pin) 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
Oct 28 15:30:05 [2] TIMER: vector=0x31 pin1=0 pin2=-1
Oct 28 15:30:05 [4] Using local APIC timer interrupts.
Oct 28 15:30:05 [4] calibrating APIC timer .
Oct 28 15:30:05 [4] . CPU clock speed is 1664.1709 MHz.
Oct 28 15:30:05 [4] . host bus clock speed is 266.2673 MHz.
Oct 28 15:30:05 [4] cpu: 0, clocks: 2662673, slice: 1331336
Oct 28 15:30:05 [4] CPU0
Oct 28 15:30:05 [4] mtrr: v1.40 (20010327) Richard Gooch (
rgooch@atnf.csiro.au)
Oct 28 15:30:05 [4] mtrr: detected mtrr type: Intel
Oct 28 15:30:05 [2] ACPI: Subsystem revision 20040326
Oct 28 15:30:05 [2] PCI: PCI BIOS revision 2.10 entry at 0xfb4c0, last bus=2
Oct 28 15:30:05 [2] PCI: Using configuration type 1
Oct 28 15:30:05 [2] ACPI: Interpreter enabled
Oct 28 15:30:05 [2] ACPI: Using IOAPIC for interrupt routing
Oct 28 15:30:05 [2] ACPI: System [ACPI] (supports S0 S1 S4 S5)
Oct 28 15:30:05 [2] ACPI: PCI Root Bridge [PCI0] (00:00)
Oct 28 15:30:05 [4] PCI: Probing PCI hardware (bus 00)
Oct 28 15:30:05 [4] PCI: nForce2 C1 Halt Disconnect fixup
Oct 28 15:30:05 [1] 0._PRT]
Oct 28 15:30:05 [1] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
Oct 28 15:30:05 [1] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *10 11 12 14 15)
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 11 *12 14 15)
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 6 7 10 11 12 14 15)
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 *7 10 11 12 14 15)
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 *4 5 6 7 10 11 12 14 15)
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Oct 28 15:30:05 [2] PCI: Probing PCI hardware
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
Oct 28 15:30:05 [1] 00:00:01[A] -> 2-23 -> IRQ 23 level high
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
Oct 28 15:30:05 [1] 00:00:02[A] -> 2-22 -> IRQ 22 level high
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21
Oct 28 15:30:05 [1] 00:00:02[B] -> 2-21 -> IRQ 21 level high
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
Oct 28 15:30:05 [1] 00:00:02[C] -> 2-20 -> IRQ 20 level high
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCI] enabled at IRQ 21
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCK] enabled at IRQ 22
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCM] enabled at IRQ 21
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [AP3C] enabled at IRQ 20
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APCZ] enabled at IRQ 22
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
Oct 28 15:30:05 [1] 00:01:06[A] -> 2-16 -> IRQ 16 level high
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
Oct 28 15:30:05 [1] 00:01:06[B] -> 2-17 -> IRQ 17 level high
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
Oct 28 15:30:05 [1] 00:01:06[C] -> 2-18 -> IRQ 18 level high
Oct 28 15:30:05 [4] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
Oct 28 15:30:05 [1] 00:01:06[D] -> 2-19 -> IRQ 19 level high
Oct 28 15:30:05 [1] number of MP IRQ sources: 16.
Oct 28 15:30:05 [1] number of IO-APIC #2 registers: 24.
Oct 28 15:30:05 [2] testing the IO APIC.
Oct 28 15:30:05 [4]
Oct 28 15:30:05 [1] IO APIC #2
Oct 28 15:30:05 [1] register #00: 02000000
Oct 28 15:30:05 [1] . : physical APIC id: 02
Oct 28 15:30:05 [1] . : Delivery Type: 0
Oct 28 15:30:05 [1] . : LTS : 0
Oct 28 15:30:05 [1] register #01: 00170011
Oct 28 15:30:05 [1] . : max redirection entries: 0017
Oct 28 15:30:05 [1] . : PRQ implemented: 0
Oct 28 15:30:05 [1] . : IO APIC version: 0011
Oct 28 15:30:05 [1] register #02: 00000000
Oct 28 15:30:05 [1] . : arbitration: 00
Oct 28 15:30:05 [1] IRQ redirection table:
Oct 28 15:30:05 [1] NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
Oct 28 15:30:05 [1] 0 0 0 0 0 1 1 31
Oct 28 15:30:05 [1] 01 001 01 0 0 0 0 0 1 1 39
Oct 28 15:30:05 [1] 02 001 01 0 0 0 0 0 1 1 41
Oct 28 15:30:05 [1] 03 001 01 0 0 0 0 0 1 1 49
Oct 28 15:30:05 [1] 04 001 01 0 0 0 0 0 1 1 51
Oct 28 15:30:05 [1] 05 001 01 0 0 0 0 0 1 1 59
Oct 28 15:30:05 [1] 06 001 01 0 0 0 0 0 1 1 61
Oct 28 15:30:05 [1] 07 001 01 0 0 0 0 0 1 1 69
Oct 28 15:30:05 [1] 08 001 01 0 0 0 0 0 1 1 71
Oct 28 15:30:05 [1] 09 001 01 0 1 0 0 0 1 1 79
Oct 28 15:30:05 [1] 0a 001 01 0 0 0 0 0 1 1 81
Oct 28 15:30:05 [1] 0b 001 01 0 0 0 0 0 1 1 89
Oct 28 15:30:05 [1] 0c 001 01 0 0 0 0 0 1 1 91
Oct 28 15:30:05 [1] 0d 001 01 0 0 0 0 0 1 1 99
Oct 28 15:30:05 [1] 0e 001 01 0 0 0 0 0 1 1 A1
Oct 28 15:30:05 [1] 0f 001 01 0 0 0 0 0 1 1 A9
Oct 28 15:30:05 [1] 10 001 01 1 1 0 0 0 1 1 D1
Oct 28 15:30:05 [1] 11 001 01 1 1 0 0 0 1 1 D9
Oct 28 15:30:05 [1] 12 001 01 1 1 0 0 0 1 1 E1
Oct 28 15:30:05 [1] 13 001 01 1 1 0 0 0 1 1 E9
Oct 28 15:30:05 [1] 14 001 01 1 1 0 0 0 1 1 C9
Oct 28 15:30:05 [1] 15 001 01 1 1 0 0 0 1 1 C1
Oct 28 15:30:05 [1] 16 001 01 1 1 0 0 0 1 1 B9
Oct 28 15:30:05 [1] 17 001 01 1 1 0 0 0 1 1 B1
Oct 28 15:30:05 [1] IRQ to pin mappings:
Oct 28 15:30:05 [1] IRQ0 -> 0:0
Oct 28 15:30:05 [1] IRQ1 -> 0:1
Oct 28 15:30:05 [1] IRQ2 -> 0:2
Oct 28 15:30:05 [1] IRQ3 -> 0:3
Oct 28 15:30:05 [1] IRQ4 -> 0:4
Oct 28 15:30:05 [1] IRQ5 -> 0:5
Oct 28 15:30:05 [1] IRQ6 -> 0:6
Oct 28 15:30:05 [1] IRQ7 -> 0:7
Oct 28 15:30:05 [1] IRQ8 -> 0:8
Oct 28 15:30:05 [1] IRQ9 -> 0:9
Oct 28 15:30:05 [1] IRQ10 -> 0:10
Oct 28 15:30:05 [1] IRQ11 -> 0:11
Oct 28 15:30:05 [1] IRQ12 -> 0:12
Oct 28 15:30:05 [1] IRQ13 -> 0:13
Oct 28 15:30:05 [1] IRQ14 -> 0:14
Oct 28 15:30:05 [1] IRQ15 -> 0:15
Oct 28 15:30:05 [1] IRQ16 -> 0:16
Oct 28 15:30:05 [1] IRQ17 -> 0:17
Oct 28 15:30:05 [1] IRQ18 -> 0:18
Oct 28 15:30:05 [1] IRQ19 -> 0:19
Oct 28 15:30:05 [1] IRQ20 -> 0:20
Oct 28 15:30:05 [1] IRQ21 -> 0:21
Oct 28 15:30:05 [1] IRQ22 -> 0:22
Oct 28 15:30:05 [1] IRQ23 -> 0:23
Oct 28 15:30:05 [2] done.
Oct 28 15:30:05 [2] PCI: Using ACPI for IRQ routing
Oct 28 15:30:05 [2] Linux NET4.0 for Linux 2.4
Oct 28 15:30:05 [2] Based upon Swansea University Computer Society NET3.039
Oct 28 15:30:05 [4] Initializing RT netlink socket
Oct 28 15:30:05 [4] Starting kswapd
Oct 28 15:30:05 [2] Journalled Block Device driver loaded
Oct 28 15:30:05 [2] devfs: v1.12c (20020818) Richard Gooch (
rgooch@atnf.csiro.au)
Oct 28 15:30:05 [2] devfs: boot_options: 0x1
Oct 28 15:30:05 [2] Installing knfsd (copyright (C) 1996
okir@monad.swb.de).
Oct 28 15:30:05 [2] ACPI: Power Button (FF) [PWRF]
Oct 28 15:30:05 [2] ACPI: Processor [CPU0] (supports C1)
Oct 28 15:30:05 [4] pty: 256 Unix98 ptys configured
Oct 28 15:30:05 [2] Real Time Clock Driver v1.10f
Oct 28 15:30:05 [2] Floppy drive(s): fd0 is 1.44M
Oct 28 15:30:05 [4] keyboard: Timeout - AT keyboard not present?(ed)
Oct 28 15:30:05 [4] keyboard: Timeout - AT keyboard not present?(f4)
Oct 28 15:30:05 [2] FDC 0 is a post-1991 82077
Oct 28 15:30:05 [4] RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Oct 28 15:30:05 [2] loop: loaded (max 8 devices)
Oct 28 15:30:05 [2] Intel(R) PRO/1000 Network Driver - version 7.3.20-k4
Oct 28 15:30:05 [2] Copyright (c) 1999-2006 Intel Corporation.
Oct 28 15:30:05 [2] dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15
Oct 28 15:30:05 [4] FW Version=$Version$
Oct 28 15:30:05 [2] pcnet32.c:v1.30h 06.24.2004
tsbogend@alpha.franken.de Oct 28 15:30:05 [2] ThunderLAN driver v1.15
Oct 28 15:30:05 [2] TLAN: 0 devices installed, PCI: 0 EISA: 0
Oct 28 15:30:05 [2] dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
Oct 28 15:30:05 [2] ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
Oct 28 15:30:05 [4] sk98lin: No adapter found.
Oct 28 15:30:05 [2] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.50.
Oct 28 15:30:05 [2] r8169 Gigabit Ethernet driver 1.2 loaded
Oct 28 15:30:05 [1] eth0: Identified chip type is 'RTL8169'.
Oct 28 15:30:05 [2] eth0: RTL8169 at 0xe0808000, 00:06:4f:80:96:b7, IRQ 16
Oct 28 15:30:05 [2] eth0: Auto-negotiation Enabled.
Oct 28 15:30:05 [2] eth0: 100Mbps Full-duplex operation.
Oct 28 15:30:05 [2] Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
Oct 28 15:30:05 [2] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Oct 28 15:30:05 [2] NFORCE2: IDE controller at PCI slot 00:09.0
Oct 28 15:30:05 [2] NFORCE2: chipset revision 162
Oct 28 15:30:05 [2] NFORCE2: not 100% native mode: will probe irqs later
Oct 28 15:30:05 [4] NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
Oct 28 15:30:05 [2] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Oct 28 15:30:05 [2] NFORCE2: 00:09.0 (rev a2) UDMA133 controller
Oct 28 15:30:05 [2] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
Oct 28 15:30:05 [2] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Oct 28 15:30:05 [4] hdb: C/H/S=30/1/0 from BIOS ignored
Oct 28 15:30:05 [4] hdb: ST3802110A, ATA DISK drive
Oct 28 15:30:05 [4] hdd: ATAPI-CD ROM-DRIVE-56MAX, ATAPI CD/DVD-ROM drive
Oct 28 15:30:05 [4] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Oct 28 15:30:05 [4] ide1 at 0x170-0x177,0x376 on irq 15
Oct 28 15:30:05 [4] ide-disk driver.
Oct 28 15:30:05 [4] hdb: host protected area => 1
Oct 28 15:30:05 [2] hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(100)
Oct 28 15:30:05 [4] hdd: attached ide-cdrom driver.
Oct 28 15:30:05 [2] hdd: ATAPI 50X CD-ROM drive, 128kB Cache
Oct 28 15:30:05 [2] Uniform CD-ROM driver Revision: 3.12
Oct 28 15:30:05 [2] Partition check:
Oct 28 15:30:05 [2] /dev/ide/host0/bus0/target1/lun0: p1
Oct 28 15:30:05 [2] SCSI subsystem driver Revision: 1.00
Oct 28 15:30:05 [2] Loading Adaptec I2O RAID: Version 2.4 Build 5
Oct 28 15:30:05 [2] Detecting Adaptec I2O RAID controllers.
Oct 28 15:30:05 [2] Red Hat/Adaptec aacraid driver (1.1-3 Dec 9 2008 22:07:18)
Oct 28 15:30:05 [4] scsi: Detection failed (no card)
Oct 28 15:30:05 [3] megaraid: v2.10.10.1 (Release Date: Thu Jan 27 16:19:44 EDT 2005)
Oct 28 15:30:05 [4] GDT-HA: Storage RAID Controller Driver. Version: 3.04
Oct 28 15:30:05 [4] GDT-HA: Found 0 PCI Storage RAID Controllers
Oct 28 15:30:05 [2] scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Oct 28 15:30:05 [4] 3ware Storage Controller device driver for Linux v1.02.00.037.
Oct 28 15:30:05 [4] 3w-xxxx: No cards found.
Oct 28 15:30:05 [1] libata version 1.20 loaded.
Oct 28 15:30:05 [1] PCI(01:08.0): version 0.9
Oct 28 15:30:05 [2] ata1: SATA max UDMA/100 cmd 0xE080E080 ctl 0xE080E08A bmdma 0xE080E000 irq 18
Oct 28 15:30:05 [2] ata2: SATA max UDMA/100 cmd 0xE080E0C0 ctl 0xE080E0CA bmdma 0xE080E008 irq 18
Oct 28 15:30:05 [1] ata1: dev 0 cfg 49:2f00 82:346b 83:7fe9 84:4773 85:3469 86:be01 87:4763 88:407f
Oct 28 15:30:05 [2] ata1: dev 0 ATA-8, max UDMA/133, 625142448 sectors: LBA48
Oct 28 15:30:05 [2] ata1: dev 0 configured for UDMA/100
Oct 28 15:30:05 [2] ata2: no device found (phy stat 00000000)
Oct 28 15:30:05 [2] scsi2 : sata_sil
Oct 28 15:30:05 [2] scsi3 : sata_sil
Oct 28 15:30:05 [4] Vendor: ATA Model: Hitachi HDT72103 Rev: ST2O
Oct 28 15:30:05 [4] Type: Direct-Access ANSI SCSI revision: 05
Oct 28 15:30:05 [4] Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
Oct 28 15:30:05 [4] SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
Oct 28 15:30:05 [2] /dev/scsi/host2/bus0/target0/lun0: p1
Oct 28 15:30:05 [2] raw1394: /dev/raw1394 device initialized
Oct 28 15:30:05 [2] sbp2: $Rev: 1074 $ Ben Collins
Oct 28 15:30:05 [5] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
Oct 28 15:30:05 [2] usb.c: registered new driver usbdevfs
Oct 28 15:30:05 [2] usb.c: registered new driver hub
Oct 28 15:30:05 [2] host/uhci.c: USB Universal Host Controller Interface driver v1.1
Oct 28 15:30:05 [2] usb.c: registered new driver usbkbd
Oct 28 15:30:05 [2] usbkbd.c: :USB HID Boot Protocol keyboard driver
Oct 28 15:30:05 [2] Initializing USB Mass Storage driver.
Oct 28 15:30:05 [2] usb.c: registered new driver usb-storage
Oct 28 15:30:05 [2] USB Mass Storage support registered.
Oct 28 15:30:05 [2] NET4: Linux TCP/IP 1.0 for NET4.0
Oct 28 15:30:05 [2] IP Protocols: ICMP, UDP, TCP
Oct 28 15:30:05 [2] IP: routing cache hash table of 4096 buckets, 32Kbytes
Oct 28 15:30:05 [2] TCP: Hash tables configured (established 32768 bind 65536)
Oct 28 15:30:05 [2] NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Oct 28 15:30:05 [3] RAMDISK: NASLite file system found at block 0
Oct 28 15:30:05 [4] <6>Freeing initrd memory: 1962k freed
Oct 28 15:30:05 [4] EXT2-fs warning: checktime reached, running e2fsck is recommended
Oct 28 15:30:05 [4] VFS: Mounted root (ext2 filesystem).
Oct 28 15:30:05 [2] Mounted devfs on /dev
Oct 28 15:30:05 [2] Freeing unused kernel memory: 560k freed
Oct 28 15:30:05 [5] ext3: No journal on filesystem on ide0(3,65)
Oct 28 15:30:05 [2] kjournald starting. Commit interval 5 seconds
Oct 28 15:30:05 [2] EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
Oct 28 15:30:05 [2] EXT3-fs: mounted filesystem with ordered data mode.