NASLite Network Attached Storage

www.serverelements.com
Task-specific simplicity with low hardware requirements.
It is currently Wed Jun 18, 2025 4:53 am

View unanswered posts | View active topics


Board index » v2.x NASLite Products » NASLite-2

All times are UTC - 5 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 
  Previous topic | Next topic 
Author Message
etien
PostPosted: Wed Nov 12, 2008 1:30 pm 
Offline

Joined: Thu Aug 11, 2005 6:31 am
Posts: 52
Location: Brighton, UK
Hi there,

longtime user of Naslite (once failed to format a floppy to correct size, been hooked ever since), with currently 5 drives (4x Ide, 1x Sata), which has been working wonderfully for a number of years.

Disc-4 (Sata) is not mounting today, and I've quickly exhausted all (meagre) resources I can offer in the way of finding out what is actually wrong with it, so I thought I'd post the Syslog. If someone finds the time and patience to have a quick look, and tell me whether this disc is fried, it would greatly help!

The only thing that has changed over the past month, apart from the occasional adding and deleting data from this backup drive, is that the Naslite box became unaccessable yesterday (it has happened on rare occasions) and the PC hosting it had to be switched off and back on, so performed its usual post-freeze check up with all drives back as normal after what seemed like a small eternity.

Thanks a lot

Quote:
* Nov 12 18:30:58 user.notice kernel: klogd started: BusyBox v1.01 (2007.03.15-22:03+0000)
* Nov 12 18:30:58 user.warn kernel: Linux version 2.4.35.NASLite (root@tzt) (gcc version 3.4.6) #2 Sun Aug 12 09:03:16 EDT 2007
* Nov 12 18:30:58 user.info kernel: BIOS-provided physical RAM map:
* Nov 12 18:30:58 user.warn kernel: BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
* Nov 12 18:30:58 user.warn kernel: BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
* Nov 12 18:30:58 user.warn kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
* Nov 12 18:30:58 user.warn kernel: BIOS-e820: 0000000000100000 - 000000000dee0000 (usable)
* Nov 12 18:30:58 user.warn kernel: BIOS-e820: 000000000dee0000 - 000000000dee3000 (ACPI NVS)
* Nov 12 18:30:58 user.warn kernel: BIOS-e820: 000000000dee3000 - 000000000def0000 (ACPI data)
* Nov 12 18:30:58 user.warn kernel: BIOS-e820: 000000000def0000 - 000000000df00000 (reserved)
* Nov 12 18:30:58 user.warn kernel: BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
* Nov 12 18:30:58 user.warn kernel: BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
* Nov 12 18:30:58 user.warn kernel: BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
* Nov 12 18:30:58 user.notice kernel: 0MB HIGHMEM available.
* Nov 12 18:30:58 user.notice kernel: 222MB LOWMEM available.
* Nov 12 18:30:58 user.warn kernel: On node 0 totalpages: 57056
* Nov 12 18:30:58 user.warn kernel: zone(0): 4096 pages.
* Nov 12 18:30:58 user.warn kernel: zone(1): 52960 pages.
* Nov 12 18:30:58 user.warn kernel: zone(2): 0 pages.
* Nov 12 18:30:58 user.info kernel: ACPI: RSDP (v000 AWARD ) @ 0x000f7c30
* Nov 12 18:30:58 user.info kernel: ACPI: RSDT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dee3040
* Nov 12 18:30:58 user.info kernel: ACPI: FADT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dee30c0
* Nov 12 18:30:58 user.info kernel: ACPI: MADT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dee6dc0
* Nov 12 18:30:58 user.info kernel: ACPI: DSDT (v001 AWARD AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
* Nov 12 18:30:58 user.warn kernel: Kernel command line: rw root=/dev/ram0 initrd=NASLite.02 quiet BOOT_IMAGE=naslite.01
* Nov 12 18:30:58 user.info kernel: Initializing CPU#0
* Nov 12 18:30:58 user.warn kernel: Detected 1599.555 MHz processor.
* Nov 12 18:30:58 user.warn kernel: Console: colour VGA+ 80x25
* Nov 12 18:30:58 user.warn kernel: Calibrating delay loop. 3191.60 BogoMIPS
* Nov 12 18:30:58 user.info kernel: Memory: 219528k/228224k available (2214k kernel code, 8308k reserved, 642k data, 540k init, 0k highmem)
* Nov 12 18:30:58 user.info kernel: Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
* Nov 12 18:30:58 user.info kernel: Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
* Nov 12 18:30:58 user.info kernel: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
* Nov 12 18:30:58 user.info kernel: Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
* Nov 12 18:30:58 user.warn kernel: Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
* Nov 12 18:30:58 user.info kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
* Nov 12 18:30:58 user.info kernel: CPU: L2 Cache: 256K (64 bytes/line)
* Nov 12 18:30:58 user.debug kernel: CPU: After generic, caps: 078bfbff e3d3fbff 00000000 00000000
* Nov 12 18:30:58 user.debug kernel: CPU: Common caps: 078bfbff e3d3fbff 00000000 00000000
* Nov 12 18:30:58 user.warn kernel: CPU: AMD Sempron(tm) Processor 2800+ stepping 00
* Nov 12 18:30:58 user.info kernel: Enabling fast FPU save and restore. done.
* Nov 12 18:30:58 user.info kernel: Enabling unmasked SIMD FPU exception support. done.
* Nov 12 18:30:58 user.info kernel: Checking 'hlt' instruction. OK.
* Nov 12 18:30:58 user.warn kernel: ACPI: IRQ9 SCI: Level Trigger.
* Nov 12 18:30:58 user.warn kernel: POSIX conformance testing by UNIFIX
* Nov 12 18:30:58 user.warn kernel: mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
* Nov 12 18:30:58 user.warn kernel: mtrr: detected mtrr type: Intel
* Nov 12 18:30:58 user.info kernel: ACPI: Subsystem revision 20040326
* Nov 12 18:30:58 user.info kernel: PCI: PCI BIOS revision 2.10 entry at 0xfa5a0, last bus=1
* Nov 12 18:30:58 user.info kernel: PCI: Using configuration type 1
* Nov 12 18:30:58 user.info kernel: ACPI: Interpreter enabled
* Nov 12 18:30:58 user.info kernel: ACPI: Using PIC for interrupt routing
* Nov 12 18:30:58 user.info kernel: ACPI: System [ACPI] (supports S0 S3 S4 S5)
* Nov 12 18:30:58 user.info kernel: ACPI: PCI Root Bridge [PCI0] (00:00)
* Nov 12 18:30:58 user.warn kernel: PCI: Probing PCI hardware (bus 00)
* Nov 12 18:30:58 user.debug kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
* Nov 12 18:30:58 user.info kernel: PCI: Probing PCI hardware
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 9
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
* Nov 12 18:30:58 user.warn kernel: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
* Nov 12 18:30:58 user.info kernel: PCI: Using ACPI for IRQ routing
* Nov 12 18:30:58 user.info kernel: Linux NET4.0 for Linux 2.4
* Nov 12 18:30:58 user.info kernel: Based upon Swansea University Computer Society NET3.039
* Nov 12 18:30:58 user.warn kernel: ket
* Nov 12 18:30:58 user.warn kernel: Starting kswapd
* Nov 12 18:30:58 user.info kernel: Journalled Block Device driver loaded
* Nov 12 18:30:58 user.info kernel: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
* Nov 12 18:30:58 user.info kernel: devfs: boot_options: 0x1
* Nov 12 18:30:58 user.info kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
* Nov 12 18:30:58 user.info kernel: ACPI: Power Button (FF) [PWRF]
* Nov 12 18:30:58 user.info kernel: ACPI: Fan [FAN] (on)
* Nov 12 18:30:58 user.info kernel: ACPI: Processor [CPU0] (supports C1)
* Nov 12 18:30:58 user.info kernel: ACPI: Thermal Zone [THRM] (41 C)
* Nov 12 18:30:58 user.warn kernel: pty: 256 Unix98 ptys configured
* Nov 12 18:30:58 user.info kernel: Real Time Clock Driver v1.10f
* Nov 12 18:30:58 user.info kernel: FDC 0 is a post-1991 82077
* Nov 12 18:30:58 user.warn kernel: RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
* Nov 12 18:30:58 user.info kernel: loop: loaded (max 8 devices)
* Nov 12 18:30:58 user.info kernel: Intel(R) PRO/1000 Network Driver - version 7.3.20-k4
* Nov 12 18:30:58 user.info kernel: Copyright (c) 1999-2006 Intel Corporation.
* Nov 12 18:30:58 user.info kernel: dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15
* Nov 12 18:30:58 user.warn kernel: FW Version=$Version$
* Nov 12 18:30:58 user.info kernel: pcnet32.c:v1.30h 06.24.2004 tsbogend@alpha.franken.de
* Nov 12 18:30:58 user.info kernel: ThunderLAN driver v1.15
* Nov 12 18:30:58 user.info kernel: TLAN: 0 devices installed, PCI: 0 EISA: 0
* Nov 12 18:30:58 user.info kernel: sis900.c: v1.08.07 11/02/2003
* Nov 12 18:30:58 user.info kernel: eth0: Realtek RTL8201 PHY transceiver found at address 1.
* Nov 12 18:30:58 user.info kernel: eth0: Using transceiver found at address 1 as default
* Nov 12 18:30:58 user.info kernel: eth0: SiS 900 PCI Fast Ethernet at 0xd400, IRQ 10, 00:01:6c:ce:f9:19.
* Nov 12 18:30:58 user.info kernel: dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
* Nov 12 18:30:58 user.info kernel: ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
* Nov 12 18:30:58 user.warn kernel: sk98lin: No adapter found.
* Nov 12 18:30:58 user.info kernel: forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.50.
* Nov 12 18:30:58 user.info kernel: 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
* Nov 12 18:30:58 user.err kernel: 8139cp: pci dev 00:09.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
* Nov 12 18:30:58 user.err kernel: 8139cp: Try the "8139too" driver instead.
* Nov 12 18:30:58 user.info kernel: 8139too Fast Ethernet driver 0.9.26
* Nov 12 18:30:58 user.info kernel: eth1: RealTek RTL8139 at 0xce807000, 00:30:bd:b8:28:7c, IRQ 10
* Nov 12 18:30:58 user.debug kernel: eth1: Identified 8139 chip type 'RTL-8100B/8139D'
* Nov 12 18:30:58 user.info kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
* Nov 12 18:30:58 user.info kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
* Nov 12 18:30:58 user.info kernel: SIS5513: IDE controller at PCI slot 00:02.5
* Nov 12 18:30:58 user.info kernel: SIS5513: chipset revision 1
* Nov 12 18:30:58 user.info kernel: SIS5513: not 100% native mode: will probe irqs later
* Nov 12 18:30:58 user.info kernel: SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
* Nov 12 18:30:58 user.info kernel: ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA
* Nov 12 18:30:58 user.info kernel: ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:DMA, hdd:DMA
* Nov 12 18:30:58 user.warn kernel: hda: WDC WD2500BB-55GUA0, ATA DISK drive
* Nov 12 18:30:58 user.warn kernel: hdb: WDC WD3000JB-00KFA0, ATA DISK drive
* Nov 12 18:30:58 user.warn kernel: hdc: ST3300831A, ATA DISK drive
* Nov 12 18:30:58 user.warn kernel: hdd: WDC WD3000JB-00KFA0, ATA DISK drive
* Nov 12 18:30:58 user.warn kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
* Nov 12 18:30:58 user.warn kernel: ide1 at 0x170-0x177,0x376 on irq 15
* Nov 12 18:30:58 user.warn kernel: hda: attached ide-disk driver.
* Nov 12 18:30:58 user.warn kernel: hda: host protected area => 1
* Nov 12 18:30:58 user.info kernel: hda: 488397168 sectors (250059 MB) w/2048KiB Cache, CHS=30401/255/63, UDMA(100)
* Nov 12 18:30:58 user.warn kernel: hdb: attached ide-disk driver.
* Nov 12 18:30:58 user.warn kernel: hdb: host protected area => 1
* Nov 12 18:30:58 user.info kernel: hdb: 586072368 sectors (300069 MB) w/8192KiB Cache, CHS=36481/255/63, UDMA(100)
* Nov 12 18:30:58 user.warn kernel: hdc: attached ide-disk driver.
* Nov 12 18:30:58 user.warn kernel: hdc: host protected area => 1
* Nov 12 18:30:58 user.info kernel: hdc: 586072368 sectors (300069 MB) w/8192KiB Cache, CHS=36481/255/63, UDMA(100)
* Nov 12 18:30:58 user.warn kernel: hdd: attached ide-disk driver.
* Nov 12 18:30:58 user.warn kernel: hdd: host protected area => 1
* Nov 12 18:30:58 user.info kernel: hdd: 586072368 sectors (300069 MB) w/8192KiB Cache, CHS=36481/255/63, UDMA(100)
* Nov 12 18:30:58 user.info kernel: Partition check:
* Nov 12 18:30:58 user.info kernel: /dev/ide/host0/bus0/target0/lun0: p1
* Nov 12 18:30:58 user.info kernel: /dev/ide/host0/bus0/target1/lun0: p1
* Nov 12 18:30:58 user.info kernel: /dev/ide/host0/bus1/target0/lun0: p1
* Nov 12 18:30:58 user.info kernel: /dev/ide/host0/bus1/target1/lun0: p1
* Nov 12 18:30:58 user.info kernel: SCSI subsystem driver Revision: 1.00
* Nov 12 18:30:58 user.info kernel: Loading Adaptec I2O RAID: Version 2.4 Build 5
* Nov 12 18:30:58 user.info kernel: Detecting Adaptec I2O RAID controllers.
* Nov 12 18:30:58 user.info kernel: Red Hat/Adaptec aacraid driver (1.1-3 Aug 12 2007 09:05:44)
* Nov 12 18:30:58 user.warn kernel: scsi: Detection failed (no card)
* Nov 12 18:30:58 user.notice kernel: megaraid: v2.10.10.1 (Release Date: Thu Jan 27 16:19:44 EDT 2005)
* Nov 12 18:30:58 user.warn kernel: GDT-HA: Storage RAID Controller Driver. Version: 3.04
* Nov 12 18:30:58 user.warn kernel: GDT-HA: Found 0 PCI Storage RAID Controllers
* Nov 12 18:30:58 user.warn kernel: 3ware Storage Controller device driver for Linux v1.02.00.037.
* Nov 12 18:30:58 user.warn kernel: 3w-xxxx: No cards found.
* Nov 12 18:30:58 user.debug kernel: libata version 1.20 loaded.
* Nov 12 18:30:58 user.info kernel: PCI(00:05.0): version 0.5
* Nov 12 18:30:58 user.info kernel: PCI(00:05.0): Detected SiS 180/181 chipset in SATA mode
* Nov 12 18:30:58 user.info kernel: ata1: SATA max UDMA/133 cmd 0xDC00 ctl 0xDD02 bmdma 0xE000 irq 11
* Nov 12 18:30:58 user.info kernel: ata2: SATA max UDMA/133 cmd 0xDE00 ctl 0xDF02 bmdma 0xE008 irq 11
* Nov 12 18:30:58 user.info kernel: ata1: no device found (phy stat 00000000)
* Nov 12 18:30:58 user.debug kernel: 7f
* Nov 12 18:30:58 user.info kernel: ata2: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
* Nov 12 18:30:58 user.info kernel: ata2: dev 0 configured for UDMA/133
* Nov 12 18:30:58 user.info kernel: scsi1 : sata_sis
* Nov 12 18:30:58 user.info kernel: scsi2 : sata_sis
* Nov 12 18:30:58 user.warn kernel: Vendor: ATA Model: WDC WD5000AAKS-0 Rev: 12.0
* Nov 12 18:30:58 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 05
* Nov 12 18:30:58 user.warn kernel: Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
* Nov 12 18:30:58 user.warn kernel: SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
* Nov 12 18:30:58 user.info kernel: /dev/scsi/host2/bus0/target0/lun0: p1
* Nov 12 18:30:58 user.info kernel: raw1394: /dev/raw1394 device initialized
* Nov 12 18:30:58 user.info kernel: sbp2: $Rev: 1074 $ Ben Collins
* Nov 12 18:30:58 user.err kernel: ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
* Nov 12 18:30:58 user.info kernel: usb.c: registered new driver usbdevfs
* Nov 12 18:30:58 user.info kernel: usb.c: registered new driver hub
* Nov 12 18:30:58 user.info kernel: ehci_hcd 00:03.3: PCI device 1039:7002
* Nov 12 18:30:58 user.info kernel: ehci_hcd 00:03.3: irq 11, pci mem ce80b000
* Nov 12 18:30:58 user.info kernel: usb.c: new USB bus registered, assigned bus number 1
* Nov 12 18:30:58 user.debug kernel: PCI: cache line size of 64 is not supported by device 00:03.3
* Nov 12 18:30:58 user.info kernel: ehci_hcd 00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
* Nov 12 18:30:58 user.info kernel: hub.c: USB hub found
* Nov 12 18:30:58 user.info kernel: hub.c: 8 ports detected
* Nov 12 18:30:58 user.info kernel: host/uhci.c: USB Universal Host Controller Interface driver v1.1
* Nov 12 18:30:58 user.info kernel: host/usb-ohci.c: USB OHCI at membase 0xce80d000, IRQ 9
* Nov 12 18:30:58 user.info kernel: host/usb-ohci.c: usb-00:03.0, PCI device 1039:7001
* Nov 12 18:30:58 user.info kernel: usb.c: new USB bus registered, assigned bus number 2
* Nov 12 18:30:58 user.info kernel: hub.c: USB hub found
* Nov 12 18:30:58 user.info kernel: hub.c: 3 ports detected
* Nov 12 18:30:58 user.info kernel: host/usb-ohci.c: USB OHCI at membase 0xce80f000, IRQ 5
* Nov 12 18:30:58 user.info kernel: host/usb-ohci.c: usb-00:03.1, PCI device 1039:7001
* Nov 12 18:30:58 user.info kernel: usb.c: new USB bus registered, assigned bus number 3
* Nov 12 18:30:58 user.info kernel: hub.c: USB hub found
* Nov 12 18:30:58 user.info kernel: hub.c: 3 ports detected
* Nov 12 18:30:58 user.info kernel: host/usb-ohci.c: USB OHCI at membase 0xce811000, IRQ 10
* Nov 12 18:30:58 user.info kernel: host/usb-ohci.c: usb-00:03.2, PCI device 1039:7001
* Nov 12 18:30:58 user.info kernel: usb.c: new USB bus registered, assigned bus number 4
* Nov 12 18:30:58 user.info kernel: hub.c: USB hub found
* Nov 12 18:30:58 user.info kernel: hub.c: 2 ports detected
* Nov 12 18:30:58 user.info kernel: usb.c: registered new driver usbkbd
* Nov 12 18:30:58 user.info kernel: usbkbd.c: :USB HID Boot Protocol keyboard driver
* Nov 12 18:30:58 user.info kernel: Initializing USB Mass Storage driver.
* Nov 12 18:30:58 user.info kernel: usb.c: registered new driver usb-storage
* Nov 12 18:30:58 user.info kernel: USB Mass Storage support registered.
* Nov 12 18:30:58 user.info kernel: NET4: Linux TCP/IP 1.0 for NET4.0
* Nov 12 18:30:58 user.info kernel: IP Protocols: ICMP, UDP, TCP
* Nov 12 18:30:58 user.info kernel: IP: routing cache hash table of 2048 buckets, 16Kbytes
* Nov 12 18:30:58 user.info kernel: TCP: Hash tables configured (established 16384 bind 32768)
* Nov 12 18:30:58 user.info kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
* Nov 12 18:30:58 user.notice kernel: RAMDISK: NASLite file system found at block 0
* Nov 12 18:30:58 user.warn kernel: <6>hub.c: new USB device 00:03.3-6, assigned address 2
* Nov 12 18:30:58 user.warn kernel: <6>scsi3 : SCSI emulation for USB Mass Storage devices
* Nov 12 18:30:58 user.warn kernel: Vendor: SanDisk Model: Cruzer Mini Rev: 0.1
* Nov 12 18:30:58 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 02
* Nov 12 18:30:58 user.warn kernel: .Attached scsi removable disk sdb at scsi3, channel 0, id 0, lun 0
* Nov 12 18:30:58 user.warn kernel: SCSI device sdb: 250879 512-byte hdwr sectors (128 MB)
* Nov 12 18:30:58 user.warn kernel: sdb: Write Protect is off
* Nov 12 18:30:58 user.info kernel: /dev/scsi/host3/bus0/target0/lun0:. unknown partition table
* Nov 12 18:30:58 user.debug kernel: WARNING: USB Mass Storage data integrity not assured
* Nov 12 18:30:58 user.debug kernel: USB Mass Storage device found at 2
* Nov 12 18:30:58 user.warn kernel: <6>Freeing initrd memory: 1962k freed
* Nov 12 18:30:58 user.warn kernel: EXT2-fs warning: checktime reached, running e2fsck is recommended
* Nov 12 18:30:58 user.warn kernel: VFS: Mounted root (ext2 filesystem).
* Nov 12 18:30:58 user.info kernel: Mounted devfs on /dev
* Nov 12 18:30:58 user.info kernel: Freeing unused kernel memory: 540k freed
* Nov 12 18:30:58 user.info kernel: eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
* Nov 12 18:30:58 user.err kernel: ata2: translated ATA stat/err 0x51/84 to SCSI SK/ASC/ASCQ 0xb/47/00
* Nov 12 18:30:58 user.warn kernel: ata2: status=0x51 { DriveReady SeekComplete Error }
* Nov 12 18:30:58 user.warn kernel: ata2: error=0x84 { DriveStatusError BadCRC }
* Nov 12 18:30:58 user.err kernel: ata2: translated ATA stat/err 0x51/84 to SCSI SK/ASC/ASCQ 0xb/47/00
* Nov 12 18:30:58 user.warn kernel: eReady SeekComplete Error }
* Nov 12 18:30:58 user.warn kernel: ata2: error=0x84 { DriveStatusError BadCRC }
* Nov 12 18:30:58 user.err kernel: ata2: translated ATA stat/err 0x51/84 to SCSI SK/ASC/ASCQ 0xb/47/00
* Nov 12 18:30:58 user.warn kernel: ata2: status=0x51 { DriveReady SeekComplete Error }
* Nov 12 18:30:58 user.warn kernel: ata2: error=0x84 { DriveStatusError BadCRC }
* Nov 12 18:30:58 user.err kernel: ata2: translated ATA stat/err 0x51/84 to SCSI SK/ASC/ASCQ 0xb/47/00
* Nov 12 18:30:58 user.warn kernel: ata2: status=0x51 { DriveReady SeekComplete Error }
* Nov 12 18:30:58 user.warn kernel: ata2: error=0x84 { DriveStatusError BadCRC }
* Nov 12 18:30:58 user.err kernel: ata2: translated ATA stat/err 0x51/84 to SCSI SK/ASC/ASCQ 0xb/47/00
* Nov 12 18:30:58 user.warn kernel: ata2: status=0x51 { DriveReady SeekComplete Error }
* Nov 12 18:30:58 user.warn kernel: ata2: error=0x84 { DriveStatusError BadCRC }
* Nov 12 18:30:58 user.err kernel: ata2: translated ATA stat/err 0x51/84 to SCSI SK/ASC/ASCQ 0xb/47/00
* Nov 12 18:30:58 user.warn kernel: ata2: status=0x51 { DriveReady SeekComplete Error }
* Nov 12 18:30:58 user.warn kernel: ata2: error=0x84 { DriveStatusError BadCRC }
* Nov 12 18:30:58 user.err kernel: ata2: translated ATA stat/err 0x51/84 to SCSI SK/ASC/ASCQ 0xb/47/00
* Nov 12 18:30:58 user.warn kernel: ata2: status=0x51 { DriveReady SeekComplete Error }
* Nov 12 18:30:58 user.warn kernel: ata2: error=0x84 { DriveStatusError BadCRC }
* Nov 12 18:30:58 user.err kernel: ata2: translated ATA stat/err 0x51/84 to SCSI SK/ASC/ASCQ 0xb/47/00
* Nov 12 18:30:58 user.warn kernel: ata2: status=0x51 { DriveReady SeekComplete Error }
* Nov 12 18:30:58 user.warn kernel: ata2: error=0x84 { DriveStatusError BadCRC }
* Nov 12 18:30:58 user.err kernel: ata2: translated ATA stat/err 0x51/84 to SCSI SK/ASC/ASCQ 0xb/47/00
* Nov 12 18:30:58 user.warn kernel: ata2: status=0x51 { DriveReady SeekComplete Error }
* Nov 12 18:30:58 user.warn kernel: ata2: error=0x84 { DriveStatusError BadCRC }
* Nov 12 18:30:58 user.err kernel: ata2: translated ATA stat/err 0x51/84 to SCSI SK/ASC/ASCQ 0xb/47/00
* Nov 12 18:30:58 user.warn kernel: ata2: status=0x51 { DriveReady SeekComplete Error }
* Nov 12 18:30:58 user.warn kernel: ata2: error=0x84 { DriveStatusError BadCRC }
* Nov 12 18:30:58 user.err kernel: ata2: command 0x25 timeout, stat 0x51 host_stat 0x1
* Nov 12 18:30:58 user.err kernel: ata2: translated ATA stat/err 0x51/84 to SCSI SK/ASC/ASCQ 0xb/47/00
* Nov 12 18:30:58 user.warn kernel: ata2: status=0x51 { DriveReady SeekComplete Error }
* Nov 12 18:30:58 user.warn kernel: ata2: error=0x84 { DriveStatusError BadCRC }
* Nov 12 18:30:58 user.warn kernel: SCSI disk error : host 2 channel 0 id 0 lun 0 return code = 8000002
* Nov 12 18:30:58 user.warn kernel: Current sd08:01: sns = 70 b
* Nov 12 18:30:58 user.warn kernel: ASC=47 ASCQ= 0
* Nov 12 18:30:58 user.warn kernel: Raw sense data:0x70 0x00 0x0b 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x47 0x00 0x00 0x00 0x00 0x00
* Nov 12 18:30:58 user.warn kernel: I/O error: dev 08:01, sector 411046072
* Nov 12 18:30:58 user.warn kernel: spurious 8259A interrupt: IRQ7.
* Nov 12 18:30:58 user.err kernel: ext3: No journal on filesystem on ide0(3,1)
* Nov 12 18:30:58 user.err kernel: ext3: No journal on filesystem on ide0(3,65)
* Nov 12 18:30:58 user.err kernel: ext3: No journal on filesystem on ide1(22,1)
* Nov 12 18:30:58 user.err kernel: ext3: No journal on filesystem on ide1(22,65)


Top
 Profile  
 
Kevlaur
PostPosted: Tue Dec 09, 2008 1:45 pm 
Offline

Joined: Wed Mar 22, 2006 5:12 pm
Posts: 37
Etien,

You might be able to save some data on off of that drive if you hook it up to another PC that has
R-linux loaded on it.

It is working, as I type, to get files off of a 300G drive that got blitzed during tropical storm hanna.

Hope this helps.

Kevlaur
Top
 Profile  
 
Tony
PostPosted: Wed Dec 10, 2008 10:35 am 
Offline
Site Admin

Joined: Tue Jul 13, 2004 4:11 pm
Posts: 1771
Location: Server Elements
Make sure the SATA cable is properly seated and working fine. Make sure the drive is set to SATA or SATA2 in accordance to the controller and using the appropriate cable. Run OEM diags on the drive to verify it's fit. If this drive has been working fine then odds are it's a cable issue.
Top
 Profile  
 
etien
PostPosted: Tue Feb 17, 2009 9:29 am 
Offline

Joined: Thu Aug 11, 2005 6:31 am
Posts: 52
Location: Brighton, UK
Thanks a lot for your replies. I just got a SATA>USB interface to try to mount the disk on my system and see if it's damaged. A SATA cable came with the device so I'll also try to change the cable in the nasbox.


EDIT

tried a new cable and checked the drive. Both seem to be fine. I'm backing up the data before trying to reformat the drive and check it extensively.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 

Board index » v2.x NASLite Products » NASLite-2

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 7 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group