NASLite Network Attached Storage

Hi all

Just fitted the above card with 4 120GB HDD's attached but can't see any HDD's listed in storage configuration - lists: * - Disk-0, SCSI-1-0-0-0.

I've entered the Adaptec configuration utility (Ctrl-A) during boot & set up a RAID 5 array & booted Nas & deleted the array & zapped each of the 4 HDD's to remove all traces of the array showing just the 4 HDD's & booted Nas but each time I get the same result when checking the storage configuration option.

I've checked that the card is not sharing IRQ's, tried moving the card to different PCI slots, checked all BIOS settings are disabled, except for floppy & USB (I boot from USB using a kicker floppy.

This card is in the supported card list!

I'm running out of ideas!

Help please


I've attached the syslog below

Jul 21 23:54:30 syslog.info syslogd started: BusyBox v1.01 (2006.02.26-22:07+0000)
Jul 21 23:54:30 daemon.info init: ^MStarting pid 1207, console /dev/null: '/sbin/klogd'
Jul 21 23:54:30 user.notice kernel: klogd started: BusyBox v1.01 (2006.02.26-22:07+0000)
Jul 21 23:54:30 user.warn kernel: Linux version 2.4.31.NASLite (root@TZT) (gcc version 3.3.6) #1 Sat Jul 8 04:34:40 UTC 2006
Jul 21 23:54:30 user.info kernel: BIOS-provided physical RAM map:
Jul 21 23:54:30 user.warn kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Jul 21 23:54:30 user.warn kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Jul 21 23:54:30 user.warn kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Jul 21 23:54:30 user.warn kernel: BIOS-e820: 0000000000100000 - 000000000fdfd000 (usable)
Jul 21 23:54:30 user.warn kernel: BIOS-e820: 000000000fdfd000 - 000000000fdff000 (ACPI data)
Jul 21 23:54:30 user.warn kernel: BIOS-e820: 000000000fdff000 - 000000000fe00000 (ACPI NVS)
Jul 21 23:54:30 user.warn kernel: BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Jul 21 23:54:30 user.notice kernel: 253MB LOWMEM available.
Jul 21 23:54:30 user.warn kernel: On node 0 totalpages: 65021
Jul 21 23:54:30 user.warn kernel: zone(0): 4096 pages.
Jul 21 23:54:30 user.warn kernel: zone(1): 60925 pages.
Jul 21 23:54:30 user.warn kernel: zone(2): 0 pages.
Jul 21 23:54:30 user.notice kernel: ACPI disabled because your bios is from 99 and too old
Jul 21 23:54:30 user.notice kernel: You can enable it with acpi=force
Jul 21 23:54:30 user.warn kernel: Kernel command line: root=/dev/ram0 rw
Jul 21 23:54:30 user.info kernel: Initializing CPU#0
Jul 21 23:54:30 user.warn kernel: Detected 533.387 MHz processor.
Jul 21 23:54:30 user.warn kernel: Console: colour VGA+ 80x25
Jul 21 23:54:30 user.warn kernel: Calibrating delay loop. 1064.96 BogoMIPS
Jul 21 23:54:30 user.info kernel: Memory: 251592k/260084k available (2169k kernel code, 8104k reserved, 727k data, 536k init, 0k highmem)
Jul 21 23:54:30 user.info kernel: Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Jul 21 23:54:30 user.info kernel: Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Jul 21 23:54:30 user.info kernel: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Jul 21 23:54:30 user.info kernel: Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Jul 21 23:54:30 user.warn kernel: Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Jul 21 23:54:30 user.info kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
Jul 21 23:54:30 user.info kernel: CPU: L2 cache: 128K
Jul 21 23:54:30 user.debug kernel: CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
Jul 21 23:54:30 user.debug kernel: CPU: Common caps: 0183f9ff 00000000 00000000 00000000
Jul 21 23:54:30 user.warn kernel: CPU: Intel Celeron (Mendocino) stepping 05
Jul 21 23:54:30 user.info kernel: Enabling fast FPU save and restore. done.
Jul 21 23:54:30 user.info kernel: Checking 'hlt' instruction. OK.
Jul 21 23:54:30 user.info kernel: Checking for popad bug. OK.
Jul 21 23:54:30 user.warn kernel: POSIX conformance testing by UNIFIX
Jul 21 23:54:30 user.info kernel: ACPI: Subsystem revision 20040326
Jul 21 23:54:30 user.info kernel: ACPI: Interpreter disabled.
Jul 21 23:54:30 user.info kernel: PCI: PCI BIOS revision 2.10 entry at 0xf04f0, last bus=1
Jul 21 23:54:30 user.info kernel: PCI: Using configuration type 1
Jul 21 23:54:30 user.info kernel: PCI: Probing PCI hardware
Jul 21 23:54:30 user.warn kernel: PCI: Probing PCI hardware (bus 00)
Jul 21 23:54:30 user.info kernel: PCI: Using IRQ router SIS5595 [1039/0008] at 00:01.0
Jul 21 23:54:30 user.info kernel: Linux NET4.0 for Linux 2.4
Jul 21 23:54:30 user.info kernel: Based upon Swansea University Computer Society NET3.039
Jul 21 23:54:30 user.warn kernel: Initializing RT netlink socket
Jul 21 23:54:30 user.warn kernel: Starting kswapd
Jul 21 23:54:30 user.info kernel: Journalled Block Device driver loaded
Jul 21 23:54:30 user.info kernel: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
Jul 21 23:54:30 user.info kernel: devfs: boot_options: 0x1
Jul 21 23:54:30 user.info kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Jul 21 23:54:30 user.warn kernel: pty: 256 Unix98 ptys configured
Jul 21 23:54:30 user.info kernel: Real Time Clock Driver v1.10f
Jul 21 23:54:30 user.info kernel: Floppy drive(s): fd0 is 1.44M
Jul 21 23:54:30 user.info kernel: FDC 0 is a post-1991 82077
Jul 21 23:54:30 user.warn kernel: RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Jul 21 23:54:30 user.info kernel: loop: loaded (max 8 devices)
Jul 21 23:54:30 user.info kernel: Intel(R) PRO/1000 Network Driver - version 5.7.6-k1
Jul 21 23:54:30 user.info kernel: Copyright (c) 1999-2004 Intel Corporation.
Jul 21 23:54:30 user.info kernel: dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15
Jul 21 23:54:30 user.warn kernel: FW Version=$Version$
Jul 21 23:54:30 user.info kernel: pcnet32.c:v1.30h 06.24.2004 tsbogend@alpha.franken.de
Jul 21 23:54:30 user.info kernel: ThunderLAN driver v1.15
Jul 21 23:54:30 user.info kernel: TLAN: 0 devices installed, PCI: 0 EISA: 0
Jul 21 23:54:30 user.info kernel: dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
Jul 21 23:54:30 user.info kernel: ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
Jul 21 23:54:30 user.warn kernel: sk98lin: No adapter found.
Jul 21 23:54:30 user.info kernel: via-rhine.c:v1.10-LK1.1.19 July-12-2003 Written by Donald Becker
Jul 21 23:54:30 user.info kernel: http://www.scyld.com/network/via-rhine.html
Jul 21 23:54:30 user.info kernel: PCI: Found IRQ 11 for device 00:0c.0
Jul 21 23:54:30 user.info kernel: eth0: VIA VT6102 Rhine-II at 0xa800, 00:50:ba:2d:a4:ac, IRQ 11.
Jul 21 23:54:30 user.info kernel: eth0: MII PHY found at address 8, status 0x782d advertising 01e1 Link 45e1.
Jul 21 23:54:30 user.info kernel: forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.30.
Jul 21 23:54:30 user.info kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
Jul 21 23:54:30 user.info kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Jul 21 23:54:30 user.info kernel: SIS5513: IDE controller at PCI slot 00:00.1
Jul 21 23:54:30 user.info kernel: SIS5513: chipset revision 208
Jul 21 23:54:30 user.info kernel: SIS5513: not 100% native mode: will probe irqs later
Jul 21 23:54:30 user.info kernel: SIS5513: SiS620 ATA 66 controller
Jul 21 23:54:30 user.info kernel: ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:pio, hdb:pio
Jul 21 23:54:30 user.info kernel: ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:pio, hdd:pio
Jul 21 23:54:30 user.info kernel: SCSI subsystem driver Revision: 1.00
Jul 21 23:54:30 user.info kernel: Red Hat/Adaptec aacraid driver (1.1-3 Jul 8 2006 04:48:23)
Jul 21 23:54:30 user.warn kernel: scsi: Detection failed (no card)
Jul 21 23:54:30 user.notice kernel: megaraid: v2.10.8.2 (Release Date: Mon Jul 26 12:15:51 EDT 2004)
Jul 21 23:54:30 user.warn kernel: GDT-HA: Storage RAID Controller Driver. Version: 3.04
Jul 21 23:54:30 user.warn kernel: GDT-HA: Found 0 PCI Storage RAID Controllers
Jul 21 23:54:30 user.warn kernel: 3ware Storage Controller device driver for Linux v1.02.00.037.
Jul 21 23:54:30 user.warn kernel: 3w-xxxx: No cards found.
Jul 21 23:54:30 user.debug kernel: libata version 1.10 loaded.
Jul 21 23:54:30 user.info kernel: raw1394: /dev/raw1394 device initialized
Jul 21 23:54:30 user.info kernel: sbp2: $Rev: 1074 $ Ben Collins
Jul 21 23:54:30 user.err kernel: ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
Jul 21 23:54:30 user.info kernel: usb.c: registered new driver usbdevfs
Jul 21 23:54:30 user.info kernel: usb.c: registered new driver hub
Jul 21 23:54:30 user.info kernel: host/uhci.c: USB Universal Host Controller Interface driver v1.1
Jul 21 23:54:30 user.info kernel: PCI: Found IRQ 3 for device 00:01.2
Jul 21 23:54:30 user.info kernel: host/usb-ohci.c: USB OHCI at membase 0xd0800000, IRQ 3
Jul 21 23:54:30 user.info kernel: host/usb-ohci.c: usb-00:01.2, PCI device 1039:7001
Jul 21 23:54:30 user.info kernel: usb.c: new USB bus registered, assigned bus number 1
Jul 21 23:54:30 user.info kernel: hub.c: USB hub found
Jul 21 23:54:30 user.info kernel: hub.c: 2 ports detected
Jul 21 23:54:30 user.info kernel: Initializing USB Mass Storage driver.
Jul 21 23:54:30 user.info kernel: usb.c: registered new driver usb-storage
Jul 21 23:54:30 user.info kernel: USB Mass Storage support registered.
Jul 21 23:54:30 user.info kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Jul 21 23:54:30 user.info kernel: IP Protocols: ICMP, UDP, TCP
Jul 21 23:54:30 user.info kernel: IP: routing cache hash table of 2048 buckets, 16Kbytes
Jul 21 23:54:30 user.info kernel: TCP: Hash tables configured (established 16384 bind 32768)
Jul 21 23:54:30 user.info kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Jul 21 23:54:30 user.notice kernel: RAMDISK: NASLite file system found at block 0
Jul 21 23:54:30 user.warn kernel: .<6>hub.c: new USB device 00:01.2-2, assigned address 2
Jul 21 23:54:30 user.warn kernel: .<6>scsi1 : SCSI emulation for USB Mass Storage devices
Jul 21 23:54:30 user.warn kernel: . Vendor: EXIGO Model: Flash Disk Rev: 2.00
Jul 21 23:54:30 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 02
Jul 21 23:54:30 user.warn kernel: .Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
Jul 21 23:54:30 user.warn kernel: SCSI device sda: 258304 512-byte hdwr sectors (132 MB)
Jul 21 23:54:30 user.warn kernel: sda: Write Protect is off
Jul 21 23:54:30 user.info kernel: Partition check:
Jul 21 23:54:30 user.info kernel: /dev/scsi/host1/bus0/target0/lun0: p1 p2 p3 p4
Jul 21 23:54:30 user.debug kernel: WARNING: USB Mass Storage data integrity not assured
Jul 21 23:54:30 user.debug kernel: USB Mass Storage device found at 2
Jul 21 23:54:30 user.warn kernel: <6>Freeing initrd memory: 1602k freed
Jul 21 23:54:30 user.warn kernel: VFS: Mounted root (ext2 filesystem).
Jul 21 23:54:30 user.info kernel: Mounted devfs on /dev
Jul 21 23:54:30 user.info kernel: Freeing unused kernel memory: 536k freed
Jul 21 23:54:30 user.info kernel: eth0: Setting full-duplex based on MII #8 link partner capability of 45e1.
Jul 21 23:54:36 auth.info login[1205]: root login on `vc/1'

I'm not quite clear on what you did here, you deleted the raid configuration in the Adaptec bios and didn't recreate it?

Where did you create the raid 5 configuration at?

Hi Ralph

Just to clarify what I've done - I have a 4 HDD (no RAID) setup that works fine using Nas 2 USB/kicker arrangement.

I wanted to test the Adaptec RAID card so I uncabled the original 4 HDD's that worked OK.

I fitted the PCI RAID card with another 4 HDD's connected to it


I created a RAID 5 array using Adaptec SMOR (Ctrl-A) using the 4 HDD's & that looked OK. I booted NAS 2 but could only see *-Disk-0, SCSI-1-0-0-0 in storage configuration.

I went back into Adaptec configuration (SMOR) & deleted the RAID 5 array & to make sure I zapped the 4 HDD's to remove all traces of the array, as per Adaptec recommendations. Adaptec showed the 4 HDD's OK

I rebooted to NAS 2 & could still only see *-Disk-0, SCSI-1-0-0-0 in storage configuration .

So it seems that however I configure the HDD's in Adaptec, NAS 2 can't see them.

This RAID card works fine in another computer setup I have running FreeNAS using a RAID 5 array created by Adaptec configuration SMOR using the same 4 HDD's.

Does the RAID configuration have to be set up by Adaptec software SMOR before booting NAS 2, as with my FreeNAS setup? Or does NAS 2 set up the RAID 5?

Hope this clarifies my problem

Just as a follow up.

Itried changing IRQ's for the Adaptec card - it is currently set to IRQ 12 withe mouse detection disabled in the BIOS but I can see no reference to IRQ 12 in the sys log (attached below)

Is it a driver problem - no driver for this card installed in NAS 2?

Jul 22 14:59:32 syslog.info syslogd started: BusyBox v1.01 (2006.02.26-22:07+0000)
Jul 22 14:59:32 daemon.info init: ^MStarting pid 1207, console /dev/null: '/sbin/klogd'
Jul 22 14:59:32 user.notice kernel: klogd started: BusyBox v1.01 (2006.02.26-22:07+0000)
Jul 22 14:59:32 user.warn kernel: Linux version 2.4.31.NASLite (root@TZT) (gcc version 3.3.6) #1 Sat Jul 8 04:34:40 UTC 2006
Jul 22 14:59:32 user.info kernel: BIOS-provided physical RAM map:
Jul 22 14:59:32 user.warn kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Jul 22 14:59:32 user.warn kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Jul 22 14:59:32 user.warn kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Jul 22 14:59:32 user.warn kernel: BIOS-e820: 0000000000100000 - 000000000fdfd000 (usable)
Jul 22 14:59:32 user.warn kernel: BIOS-e820: 000000000fdfd000 - 000000000fdff000 (ACPI data)
Jul 22 14:59:32 user.warn kernel: BIOS-e820: 000000000fdff000 - 000000000fe00000 (ACPI NVS)
Jul 22 14:59:32 user.warn kernel: BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Jul 22 14:59:32 user.notice kernel: 253MB LOWMEM available.
Jul 22 14:59:32 user.warn kernel: On node 0 totalpages: 65021
Jul 22 14:59:32 user.warn kernel: zone(0): 4096 pages.
Jul 22 14:59:32 user.warn kernel: zone(1): 60925 pages.
Jul 22 14:59:32 user.warn kernel: zone(2): 0 pages.
Jul 22 14:59:32 user.notice kernel: ACPI disabled because your bios is from 99 and too old
Jul 22 14:59:32 user.notice kernel: You can enable it with acpi=force
Jul 22 14:59:32 user.warn kernel: Kernel command line: root=/dev/ram0 rw
Jul 22 14:59:32 user.info kernel: Initializing CPU#0
Jul 22 14:59:32 user.warn kernel: Detected 533.386 MHz processor.
Jul 22 14:59:32 user.warn kernel: Console: colour VGA+ 80x25
Jul 22 14:59:32 user.warn kernel: Calibrating delay loop. 1064.96 BogoMIPS
Jul 22 14:59:32 user.info kernel: Memory: 251592k/260084k available (2169k kernel code, 8104k reserved, 727k data, 536k init, 0k highmem)
Jul 22 14:59:32 user.info kernel: Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Jul 22 14:59:32 user.info kernel: Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Jul 22 14:59:32 user.info kernel: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Jul 22 14:59:32 user.info kernel: Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Jul 22 14:59:32 user.warn kernel: Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Jul 22 14:59:32 user.info kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
Jul 22 14:59:32 user.info kernel: CPU: L2 cache: 128K
Jul 22 14:59:32 user.debug kernel: CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
Jul 22 14:59:32 user.debug kernel: CPU: Common caps: 0183f9ff 00000000 00000000 00000000
Jul 22 14:59:32 user.warn kernel: CPU: Intel Celeron (Mendocino) stepping 05
Jul 22 14:59:32 user.info kernel: Enabling fast FPU save and restore. done.
Jul 22 14:59:32 user.info kernel: Checking 'hlt' instruction. OK.
Jul 22 14:59:32 user.info kernel: Checking for popad bug. OK.
Jul 22 14:59:32 user.warn kernel: POSIX conformance testing by UNIFIX
Jul 22 14:59:32 user.info kernel: ACPI: Subsystem revision 20040326
Jul 22 14:59:32 user.info kernel: ACPI: Interpreter disabled.
Jul 22 14:59:32 user.info kernel: PCI: PCI BIOS revision 2.10 entry at 0xf04f0, last bus=1
Jul 22 14:59:32 user.info kernel: PCI: Using configuration type 1
Jul 22 14:59:32 user.info kernel: PCI: Probing PCI hardware
Jul 22 14:59:32 user.warn kernel: PCI: Probing PCI hardware (bus 00)
Jul 22 14:59:32 user.info kernel: PCI: Using IRQ router SIS5595 [1039/0008] at 00:01.0
Jul 22 14:59:32 user.info kernel: Linux NET4.0 for Linux 2.4
Jul 22 14:59:32 user.info kernel: Based upon Swansea University Computer Society NET3.039
Jul 22 14:59:32 user.warn kernel: Initializing RT netlink socket
Jul 22 14:59:32 user.warn kernel: Starting kswapd
Jul 22 14:59:32 user.info kernel: Journalled Block Device driver loaded
Jul 22 14:59:32 user.info kernel: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
Jul 22 14:59:32 user.info kernel: devfs: boot_options: 0x1
Jul 22 14:59:32 user.info kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Jul 22 14:59:32 user.warn kernel: pty: 256 Unix98 ptys configured
Jul 22 14:59:32 user.info kernel: Real Time Clock Driver v1.10f
Jul 22 14:59:32 user.info kernel: Floppy drive(s): fd0 is 1.44M
Jul 22 14:59:32 user.info kernel: FDC 0 is a post-1991 82077
Jul 22 14:59:32 user.warn kernel: RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Jul 22 14:59:32 user.info kernel: loop: loaded (max 8 devices)
Jul 22 14:59:32 user.info kernel: Intel(R) PRO/1000 Network Driver - version 5.7.6-k1
Jul 22 14:59:32 user.info kernel: Copyright (c) 1999-2004 Intel Corporation.
Jul 22 14:59:32 user.info kernel: dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15
Jul 22 14:59:32 user.warn kernel: FW Version=$Version$
Jul 22 14:59:32 user.info kernel: pcnet32.c:v1.30h 06.24.2004 tsbogend@alpha.franken.de
Jul 22 14:59:32 user.info kernel: ThunderLAN driver v1.15
Jul 22 14:59:32 user.info kernel: TLAN: 0 devices installed, PCI: 0 EISA: 0
Jul 22 14:59:32 user.info kernel: dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
Jul 22 14:59:32 user.info kernel: ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
Jul 22 14:59:32 user.warn kernel: sk98lin: No adapter found.
Jul 22 14:59:32 user.info kernel: via-rhine.c:v1.10-LK1.1.19 July-12-2003 Written by Donald Becker
Jul 22 14:59:32 user.info kernel: http://www.scyld.com/network/via-rhine.html
Jul 22 14:59:32 user.info kernel: PCI: Found IRQ 11 for device 00:0c.0
Jul 22 14:59:32 user.info kernel: eth0: VIA VT6102 Rhine-II at 0xa800, 00:50:ba:2d:a4:ac, IRQ 11.
Jul 22 14:59:32 user.info kernel: eth0: MII PHY found at address 8, status 0x782d advertising 01e1 Link 45e1.
Jul 22 14:59:32 user.info kernel: forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.30.
Jul 22 14:59:32 user.info kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
Jul 22 14:59:32 user.info kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Jul 22 14:59:32 user.info kernel: SIS5513: IDE controller at PCI slot 00:00.1
Jul 22 14:59:32 user.info kernel: SIS5513: chipset revision 208
Jul 22 14:59:32 user.info kernel: SIS5513: not 100% native mode: will probe irqs later
Jul 22 14:59:32 user.info kernel: SIS5513: SiS620 ATA 66 controller
Jul 22 14:59:32 user.info kernel: ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:pio, hdb:pio
Jul 22 14:59:32 user.info kernel: ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:pio, hdd:pio
Jul 22 14:59:32 user.info kernel: SCSI subsystem driver Revision: 1.00
Jul 22 14:59:32 user.info kernel: Red Hat/Adaptec aacraid driver (1.1-3 Jul 8 2006 04:48:23)
Jul 22 14:59:32 user.warn kernel: scsi: Detection failed (no card)
Jul 22 14:59:32 user.notice kernel: megaraid: v2.10.8.2 (Release Date: Mon Jul 26 12:15:51 EDT 2004)
Jul 22 14:59:32 user.warn kernel: GDT-HA: Storage RAID Controller Driver. Version: 3.04
Jul 22 14:59:32 user.warn kernel: GDT-HA: Found 0 PCI Storage RAID Controllers
Jul 22 14:59:32 user.warn kernel: 3ware Storage Controller device driver for Linux v1.02.00.037.
Jul 22 14:59:32 user.warn kernel: 3w-xxxx: No cards found.
Jul 22 14:59:32 user.debug kernel: libata version 1.10 loaded.
Jul 22 14:59:32 user.info kernel: raw1394: /dev/raw1394 device initialized
Jul 22 14:59:32 user.info kernel: sbp2: $Rev: 1074 $ Ben Collins
Jul 22 14:59:32 user.err kernel: ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
Jul 22 14:59:32 user.info kernel: usb.c: registered new driver usbdevfs
Jul 22 14:59:32 user.info kernel: usb.c: registered new driver hub
Jul 22 14:59:32 user.info kernel: host/uhci.c: USB Universal Host Controller Interface driver v1.1
Jul 22 14:59:32 user.info kernel: PCI: Found IRQ 4 for device 00:01.2
Jul 22 14:59:32 user.info kernel: host/usb-ohci.c: USB OHCI at membase 0xd0800000, IRQ 4
Jul 22 14:59:32 user.info kernel: host/usb-ohci.c: usb-00:01.2, PCI device 1039:7001
Jul 22 14:59:32 user.info kernel: usb.c: new USB bus registered, assigned bus number 1
Jul 22 14:59:32 user.info kernel: hub.c: USB hub found
Jul 22 14:59:32 user.info kernel: hub.c: 2 ports detected
Jul 22 14:59:32 user.info kernel: Initializing USB Mass Storage driver.
Jul 22 14:59:32 user.info kernel: usb.c: registered new driver usb-storage
Jul 22 14:59:32 user.info kernel: USB Mass Storage support registered.
Jul 22 14:59:32 user.info kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Jul 22 14:59:32 user.info kernel: IP Protocols: ICMP, UDP, TCP
Jul 22 14:59:32 user.info kernel: IP: routing cache hash table of 2048 buckets, 16Kbytes
Jul 22 14:59:32 user.info kernel: TCP: Hash tables configured (established 16384 bind 32768)
Jul 22 14:59:32 user.info kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Jul 22 14:59:32 user.notice kernel: RAMDISK: NASLite file system found at block 0
Jul 22 14:59:32 user.warn kernel: .<6>hub.c: new USB device 00:01.2-2, assigned address 2
Jul 22 14:59:32 user.warn kernel: .<6>scsi1 : SCSI emulation for USB Mass Storage devices
Jul 22 14:59:32 user.warn kernel: . Vendor: EXIGO Model: Flash Disk Rev: 2.00
Jul 22 14:59:32 user.warn kernel: Type: Direct-Access ANSI SCSI revision: 02
Jul 22 14:59:32 user.warn kernel: Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
Jul 22 14:59:32 user.warn kernel: .SCSI device sda: 258304 512-byte hdwr sectors (132 MB)
Jul 22 14:59:32 user.warn kernel: sda: Write Protect is off
Jul 22 14:59:32 user.info kernel: Partition check:
Jul 22 14:59:32 user.info kernel: /dev/scsi/host1/bus0/target0/lun0:. p1 p2 p3 p4
Jul 22 14:59:32 user.debug kernel: WARNING: USB Mass Storage data integrity not assured
Jul 22 14:59:32 user.debug kernel: USB Mass Storage device found at 2
Jul 22 14:59:32 user.warn kernel: .<6>Freeing initrd memory: 1602k freed
Jul 22 14:59:32 user.warn kernel: VFS: Mounted root (ext2 filesystem).
Jul 22 14:59:32 user.info kernel: Mounted devfs on /dev
Jul 22 14:59:32 user.info kernel: Freeing unused kernel memory: 536k freed
Jul 22 14:59:32 user.info kernel: eth0: Setting full-duplex based on MII #8 link partner capability of 45e1.
Jul 22 14:59:37 auth.info login[1205]: root login on `vc/1'

Hi Chris,



The syslog should include a line regarding I2O RAID, which is the driver pertaining to your card. I didn't see it, so a quick look at the source made it clear that it never made it into the final kernel. I'll make sure that it makes it in v2.01 due out in the next couple of days.

Please accept my oppology for the confusion. The driver was in earlier beta kernels, so the removal was in error.