Thanks for your help!
I'll post the Syslog below (made after failed drive was replaced - it doesn't show the Syslog before the drive failure; I didn't think to copy and paste it out).
I suppose I need to reframe the earlier question about the Syslog; Where can I go or how can I get the information that will give me the ability to learn how to read the Syslogs for myself? I've look everywhere on the net and ServerElements site without much luck.
I don't know a lot about Linux; is this why I can't understand the Syslog?
Thanks again for your help, it's much appreciated.
Oct 5 01:34:50 [3] klogd started: BusyBox v1.12.1 (2009-11-19 21:21:30 UTC)
Oct 5 01:34:50 [3] Linux version 2.6.30.3.CORE3 (root@DevBox) (gcc version 4.1.2 (SE 4.1.2 p1.0.2)) #1 Wed Jul 14 01:02:59 UTC 2010
Oct 5 01:34:50 [2] KERNEL supported cpus:
Oct 5 01:34:50 [2] Intel GenuineIntel
Oct 5 01:34:50 [2] AMD AuthenticAMD
Oct 5 01:34:50 [2] NSC Geode by NSC
Oct 5 01:34:50 [2] Cyrix CyrixInstead
Oct 5 01:34:50 [2] Centaur CentaurHauls
Oct 5 01:34:50 [2] Transmeta GenuineTMx86
Oct 5 01:34:50 [2] Transmeta TransmetaCPU
Oct 5 01:34:50 [2] UMC UMC UMC UMC
Oct 5 01:34:50 [2] BIOS-provided physical RAM map:
Oct 5 01:34:50 [2] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Oct 5 01:34:50 [2] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Oct 5 01:34:50 [2] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
Oct 5 01:34:50 [2] BIOS-e820: 0000000000100000 - 000000001ef2fc00 (usable)
Oct 5 01:34:50 [2] BIOS-e820: 000000001ef2fc00 - 000000001ef30000 (ACPI NVS)
Oct 5 01:34:50 [2] BIOS-e820: 000000001ef30000 - 000000001ef40000 (ACPI data)
Oct 5 01:34:50 [2] BIOS-e820: 000000001ef40000 - 000000001eff0000 (ACPI NVS)
Oct 5 01:34:50 [2] BIOS-e820: 000000001eff0000 - 000000001f000000 (reserved)
Oct 5 01:34:50 [2] BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved)
Oct 5 01:34:50 [2] BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
Oct 5 01:34:50 [2] DMI 2.3 present.
Oct 5 01:34:50 [2] last_pfn = 0x1ef2f max_arch_pfn = 0x100000
Oct 5 01:34:50 [2] init_memory_mapping: 0000000000000000-000000001ef2f000
Oct 5 01:34:50 [1] 0000000000 - 0000400000 page 4k
Oct 5 01:34:50 [1] 0000400000 - 001ec00000 page 2M
Oct 5 01:34:50 [1] 001ec00000 - 001ef2f000 page 4k
Oct 5 01:34:50 [1] kernel direct mapping tables up to 1ef2f000 @ 7000-c000
Oct 5 01:34:50 [2] RAMDISK: 1e656000 - 1ef0e93a
Oct 5 01:34:50 [4] ACPI: RSDP 000f61b0 00014 (v00 ACPIAM)
Oct 5 01:34:50 [4] ACPI: RSDT 1ef30000 00038 (v01 INTEL D865GLC 20040421 MSFT 00000097)
Oct 5 01:34:50 [4] ACPI: FACP 1ef30200 00081 (v02 INTEL D865GLC 20040421 MSFT 00000097)
Oct 5 01:34:50 [4] ACPI: DSDT 1ef30370 04231 (v01 INTEL D865GLC 00000001 MSFT 0100000D)
Oct 5 01:34:50 [4] ACPI: FACS 1ef40000 00040
Oct 5 01:34:50 [4] ACPI: APIC 1ef30300 00068 (v01 INTEL D865GLC 20040421 MSFT 00000097)
Oct 5 01:34:50 [4] ACPI: ASF! 1ef345b0 00099 (v16 LEGEND I865PASF 00000001 MSFT 0100000D)
Oct 5 01:34:50 [4] ACPI: TCPA 1ef34649 00034 (v01 INTEL TBLOEMID 00000001 MSFT 00000097)
Oct 5 01:34:50 [4] ACPI: WDDT 1ef3467d 00040 (v01 INTEL OEMWDDT 00000001 MSFT 0100000D)
Oct 5 01:34:50 [1] ACPI: Local APIC address 0xfee00000
Oct 5 01:34:50 [3] 0MB HIGHMEM available.
Oct 5 01:34:50 [3] 495MB LOWMEM available.
Oct 5 01:34:50 [2] mapped low ram: 0 - 1ef2f000
Oct 5 01:34:50 [2] low ram: 0 - 1ef2f000
Oct 5 01:34:50 [2] node 0 low ram: 00000000 - 1ef2f000
Oct 5 01:34:50 [2] node 0 bootmap 00001000 - 00004de8
Oct 5 01:34:50 [2] (7 early reservations) ==> bootmem [0000000000 - 001ef2f000]
Oct 5 01:34:50 [2] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
Oct 5 01:34:50 [2] #1 [0000100000 - 000039b83c] TEXT DATA BSS ==> [0000100000 - 000039b83c]
Oct 5 01:34:50 [2] #2 [001e656000 - 001ef0e93a] RAMDISK ==> [001e656000 - 001ef0e93a]
Oct 5 01:34:50 [2] #3 [000009a000 - 0000100000] BIOS reserved ==> [000009a000 - 0000100000]
Oct 5 01:34:50 [2] #4 [000039c000 - 000039e18c] BRK ==> [000039c000 - 000039e18c]
Oct 5 01:34:50 [2] #5 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
Oct 5 01:34:50 [2] #6 [0000001000 - 0000005000] BOOTMAP ==> [0000001000 - 0000005000]
Oct 5 01:34:50 [2] found SMP MP-table at [c00ff780] ff780
Oct 5 01:34:50 [4] Zone PFN ranges:
Oct 5 01:34:50 [4] DMA 0x00000000 -> 0x00001000
Oct 5 01:34:50 [4] Normal 0x00001000 -> 0x0001ef2f
Oct 5 01:34:50 [4] HighMem 0x0001ef2f -> 0x0001ef2f
Oct 5 01:34:50 [4] Movable zone start PFN for each node
Oct 5 01:34:50 [4] early_node_map[2] active PFN ranges
Oct 5 01:34:50 [4] 0: 0x00000000 -> 0x0000009f
Oct 5 01:34:50 [4] 0: 0x00000100 -> 0x0001ef2f
Oct 5 01:34:50 [1] On node 0 totalpages: 126670
Oct 5 01:34:50 [1] free_area_init_node: node 0, pgdat c031d560, node_mem_map c1000000
Oct 5 01:34:50 [1] DMA zone: 32 pages used for memmap
Oct 5 01:34:50 [1] DMA zone: 0 pages reserved
Oct 5 01:34:50 [1] DMA zone: 3967 pages, LIFO batch:0
Oct 5 01:34:50 [1] Normal zone: 959 pages used for memmap
Oct 5 01:34:50 [1] Normal zone: 121712 pages, LIFO batch:31
Oct 5 01:34:50 [2] Using APIC driver default
Oct 5 01:34:50 [2] ACPI: PM-Timer IO Port: 0x408
Oct 5 01:34:50 [1] ACPI: Local APIC address 0xfee00000
Oct 5 01:34:50 [2] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Oct 5 01:34:50 [2] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Oct 5 01:34:50 [4] ACPI: NR_CPUS/possible_cpus limit of 1 reached. Processor 1/0x1 ignored.
Oct 5 01:34:50 [2] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
Oct 5 01:34:50 [2] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
Oct 5 01:34:50 [2] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
Oct 5 01:34:50 [2] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
Oct 5 01:34:50 [2] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Oct 5 01:34:50 [2] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Oct 5 01:34:50 [1] ACPI: IRQ0 used by override.
Oct 5 01:34:50 [1] ACPI: IRQ2 used by over
Oct 5 01:34:50 [2] ride.
Oct 5 01:34:50 [1] ACPI: IRQ9 used by override.
Oct 5 01:34:50 [2] Enabling APIC mode: Flat. Using 1 I/O APICs
Oct 5 01:34:50 [2] Using ACPI (MADT) for SMP configuration information
Oct 5 01:34:50 [1] nr_irqs_gsi: 24
Oct 5 01:34:50 [2] Allocating PCI resources starting at 20000000 (gap: 1f000000:dfcf0000)
Oct 5 01:34:50 [4] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125679
Oct 5 01:34:50 [3] Kernel command line: rw root=/dev/ram0 initrd=NASLite.02 quiet BOOT_IMAGE=NASLite.01
Oct 5 01:34:50 [2] Enabling fast FPU save and restore. done.
Oct 5 01:34:50 [2] Enabling unmasked SIMD FPU exception support. done.
Oct 5 01:34:50 [2] Initializing CPU#0
Oct 5 01:34:50 [2] NR_IRQS:288
Oct 5 01:34:50 [4] PID hash table entries: 2048 (order: 11, 8192 bytes)
Oct 5 01:34:50 [4] Fast TSC calibration using PIT
Oct 5 01:34:50 [4] Detected 2792.939 MHz processor.
Oct 5 01:34:50 [4] Console: colour VGA+ 80x25
Oct 5 01:34:50 [2] console [tty0] enabled
Oct 5 01:34:50 [2] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Oct 5 01:34:50 [2] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Oct 5 01:34:50 [2] Initializing HighMem for node 0 (00000000:00000000)
Oct 5 01:34:50 [2] Memory: 490336k/507068k available (1523k kernel code, 16016k reserved, 667k data, 208k init, 0k highmem)
Oct 5 01:34:50 [2] virtual kernel memory layout:
Oct 5 01:34:50 [2] fixmap : 0xfffa9000 - 0xfffff000 ( 344 kB)
Oct 5 01:34:50 [2] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
Oct 5 01:34:50 [2] vmalloc : 0xdf72f000 - 0xff7fe000 ( 512 MB)
Oct 5 01:34:50 [2] lowmem : 0xc0000000 - 0xdef2f000 ( 495 MB)
Oct 5 01:34:50 [2] .init : 0xc0326000 - 0xc035a000 ( 208 kB)
Oct 5 01:34:50 [2] .data : 0xc027cfdb - 0xc0323e14 ( 667 kB)
Oct 5 01:34:50 [2] .text : 0xc0100000 - 0xc027cfdb (1523 kB)
Oct 5 01:34:50 [2] Checking if this processor honours the WP bit even in supervisor mode.Ok.
Oct 5 01:34:50 [2] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Oct 5 01:34:50 [2] Calibrating delay loop (skipped), value calculated using timer frequency 5585.87 BogoMIPS (lpj=11171756)
Oct 5 01:34:50 [4] Mount-cache hash table entries: 512
Oct 5 01:34:50 [2] CPU: Trace cache: 12K uops, L1 D cache: 8K
Oct 5 01:34:50 [2] CPU: L2 cache: 512K
Oct 5 01:34:50 [4] CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Oct 5 01:34:50 [2] Checking 'hlt' instruction. OK.
Oct 5 01:34:50 [2] ACPI: Core revision 20090320
Oct 5 01:34:50 [2] net_namespace: 296 bytes
Oct 5 01:34:50 [2] NET: Registered protocol family 16
Oct 5 01:34:50 [2] ACPI: bus type pci registered
Oct 5 01:34:50 [2] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
Oct 5 01:34:50 [2] PCI: Using configuration type 1 for base access
Oct 5 01:34:50 [4] bio: create slab at 0
Oct 5 01:34:50 [1] ACPI: EC: Look up EC in DSDT
Oct 5 01:34:50 [2] ACPI: Interpreter enabled
Oct 5 01:34:50 [2] ACPI: (supports S0 S5)
Oct 5 01:34:50 [2] ACPI: Using IOAPIC for interrupt routing
Oct 5 01:34:50 [2] ACPI: Power Resource [URP1] (off)
Oct 5 01:34:50 [2] ACPI: Power Resource [FDDP] (off)
Oct 5 01:34:50 [2] ACPI: Power Resource [LPTP] (off)
Oct 5 01:34:50 [2] ACPI: No dock devices found.
Oct 5 01:34:50 [2] ACPI: PCI Root Bridge [PCI0] (0000:00)
Oct 5 01:34:50 [1] pci 0000:00:00.0: reg 10 32bit mmio: [0xf8000000-0xfbffffff]
Oct 5 01:34:50 [1] pci 0000:00:02.0: reg 10 32bit mmio: [0xf0000000-0xf7ffffff]
Oct 5 01:34:50 [1] pci 0000:00:02.0: reg 14 32bit mmio: [0xffa80000-0xffafffff]
Oct 5 01:34:50 [1] pci 0000:00:02.0: reg 18 io port: [0xec00-0xec07]
Oct 5 01:34:50 [1] pci 0000:00:1d.0: reg 20 io port: [0xc800-0xc81f]
Oct 5 01:34:50 [1] pci 0000:00:1d.1: reg 20 io port: [0xcc00-0xcc1f]
Oct 5 01:34:50 [1] pci 0000:00:1d.2: reg 20 io port: [0xd000-0xd01f]
Oct 5 01:34:50 [1] pci 0000:00:1d.3: reg 20 io port: [0xd400-0xd41f]
Oct 5 01:34:50 [1] pci 0000:00:1d.7: reg 10 32bit mmio: [0xffa7fc00-0xffa7ffff]
Oct 5 01:34:50 [2] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
Oct 5 01:34:50 [2] pci 0000:00:1d.7: PME# disabled
Oct 5 01:34:50 [2] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
Oct 5 01:34:50 [2] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH4 GPIO
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff]
Oct 5 01:34:50 [1] pci 0000:00:1f.2: reg 10 io port: [0xe800-0xe807]
Oct 5 01:34:50 [1] pci 0000:00:1f.2: reg 14 io port: [0xe400-0xe403]
Oct 5 01:34:50 [1] pci 0000:00:1f.2: reg 18 io port: [0xe000-0xe007]
Oct 5 01:34:50 [1] pci 0000:00:1f.2: reg 1c io port: [0xdc00-0xdc03]
Oct 5 01:34:50 [1] pci 0000:00:1f.2: reg 20 io port: [0xd800-0xd80f]
Oct 5 01:34:50 [1] pci 0000:00:1f.3: reg 20 io port: [0xc400-0xc41f]
Oct 5 01:34:50 [1] pci 0000:01:00.0: reg 10 64bit mmio: [0xff800000-0xff8fffff]
Oct 5 01:34:50 [1] pci 0000:01:00.0: reg 18 io port: [0xb800-0xb8ff]
Oct 5 01:34:50 [1] pci 0000:01:01.0: reg 10 64bit mmio: [0xff600000-0xff6fffff]
Oct 5 01:34:50 [1] pci 0000:01:01.0: reg 18 io port: [0xb400-0xb4ff]
Oct 5 01:34:50 [1] pci 0000:01:08.0: reg 10 32bit mmio: [0xff4ff000-0xff4fffff]
Oct 5 01:34:50 [1] pci 0000:01:08.0: reg 14 io port: [0xbc00-0xbc3f]
Oct 5 01:34:50 [1] pci 0000:01:08.0: supports D1 D2
Oct 5 01:34:50 [2] pci 0000:01:08.0: PME# supported from D0 D1 D2 D3hot D3cold
Oct 5 01:34:50 [2] pci 0000:01:08.0: PME# disabled
Oct 5 01:34:50 [2] pci 0000:00:1e.0: transparent bridge
Oct 5 01:34:50 [1] pci 0000:00:1e.0: bridge io port: [0xb000-0xbfff]
Oct 5 01:34:50 [1] pci 0000:00:1e.0: bridge 32bit mmio: [0xff000000-0xff8fffff]
Oct 5 01:34:50 [1] pci 0000:00:1e.0: bridge 32bit mmio pref: [0xe6a00000-0xe6afffff]
Oct 5 01:34:50 [1] pci_bus 0000:00: on NUMA node 0
Oct 5 01:34:50 [1] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Oct 5 01:34:50 [1] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 *4 5 6 7 9 10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Oct 5 01:34:50 [2] PCI: Using ACPI for IRQ routing
Oct 5 01:34:50 [1]
Oct 5 01:34:50 [1] printing PIC contents
Oct 5 01:34:50 [1] . PIC IMR: ffff
Oct 5 01:34:50 [1] . PIC IRR: 0000
Oct 5 01:34:50 [1] . PIC ISR: 0000
Oct 5 01:34:50 [1] . PIC ELCR: 0eb8
Oct 5 01:34:50 [4]
Oct 5 01:34:50 [1] printing local APIC contents on CPU#0/0:
Oct 5 01:34:50 [2] . APIC ID: 00000000 (0)
Oct 5 01:34:50 [2] . APIC VERSION: 00050014
Oct 5 01:34:50 [1] . APIC TASKPRI: 00000000 (00)
Oct 5 01:34:50 [1] . APIC PROCPRI: 00000000
Oct 5 01:34:50 [1] . APIC LDR: 01000000
Oct 5 01:34:50 [1] . APIC DFR: ffffffff
Oct 5 01:34:50 [1] . APIC SPIV: 000001ff
Oct 5 01:34:50 [1] . APIC ISR field:
Oct 5 01:34:50 [1] 0123456789abcdef0123456789abcdef
Oct 5 01:34:50 [1] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [1] . APIC TMR field:
Oct 5 01:34:50 [1] 0123456789abcdef0123456789abcdef
Oct 5 01:34:50 [1] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [1] . APIC IRR field:
Oct 5 01:34:50 [1] 0123456789abcdef0123456789abcdef
Oct 5 01:34:50 [1] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [1] . APIC ESR: 00000000
Oct 5 01:34:50 [1] . APIC ICR: 00000630
Oct 5 01:34:50 [1] . APIC ICR2: 01000000
Oct 5 01:34:50 [1] . APIC LVTT: 000200ef
Oct 5 01:34:50 [1] . APIC LVTPC: 00010000
Oct 5 01:34:50 [1] . APIC LVT0: 00010700
Oct 5 01:34:50 [1] . APIC LVT1: 00000400
Oct 5 01:34:50 [1] . APIC LVTERR: 000000fe
Oct 5 01:34:50 [1] . APIC TMICT: 0000c2d5
Oct 5 01:34:50 [1] . APIC TMCCT: 000075c5
Oct 5 01:34:50 [1] . APIC TDCR: 00000003
Oct 5 01:34:50 [4]
Oct 5 01:34:50 [1] number of MP IRQ sources: 15.
Oct 5 01:34:50 [1] number of IO-APIC #2 registers: 24.
Oct 5 01:34:50 [2] testing the IO APIC.
Oct 5 01:34:50 [4]
Oct 5 01:34:50 [1] IO APIC #2
Oct 5 01:34:50 [1] register #00: 02000000
Oct 5 01:34:50 [1] . : physical APIC id: 02
Oct 5 01:34:50 [1] . : Delivery Type: 0
Oct 5 01:34:50 [1] . : LTS : 0
Oct 5 01:34:50 [1] register #01: 00178020
Oct 5 01:34:50 [1] . : max redirection entries: 0017
Oct 5 01:34:50 [1] . : PRQ implemented: 1
Oct 5 01:34:50 [1] . : IO APIC version: 0020
Oct 5 01:34:50 [1] IRQ redirection table:
Oct 5 01:34:50 [1] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
Oct 5 01:34:50 [1] 00 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 01 001 0 0 0 0 0 1 1 31
Oct 5 01:34:50 [1] 02 001 0 0 0 0 0 1 1 30
Oct 5 01:34:50 [1] 03 001 0 0 0 0 0 1 1 33
Oct 5 01:34:50 [1] 04 001 0 0 0 0 0 1 1 34
Oct 5 01:34:50 [1] 05 001 0 0 0 0 0 1 1 35
Oct 5 01:34:50 [1] 06 001 0 0 0 0 0 1 1 36
Oct 5 01:34:50 [1] 07 001 0 0 0 0 0 1 1 37
Oct 5 01:34:50 [1] 08 001 0 0 0 0 0 1 1 38
Oct 5 01:34:50 [1] 09 001 0 1 0 0 0 1 1 39
Oct 5 01:34:50 [1] 0a 001 0 0 0 0 0 1 1 3A
Oct 5 01:34:50 [1] 0b 001 0 0 0 0 0 1 1 3B
Oct 5 01:34:50 [1] 0c 001 0 0 0 0 0 1 1 3C
Oct 5 01:34:50 [1] 0d 001 0 0 0 0 0
Oct 5 01:34:50 [2] 1 1 3D
Oct 5 01:34:50 [1] 0e 001 0 0 0 0 0 1 1 3E
Oct 5 01:34:50 [1] 0f 001 0 0 0 0 0 1 1 3F
Oct 5 01:34:50 [1] 10 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 11 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 12 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 13 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 14 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 15 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 16 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 17 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] IRQ to pin mappings:
Oct 5 01:34:50 [1] IRQ0 -> 0:2
Oct 5 01:34:50 [1] IRQ1 -> 0:1
Oct 5 01:34:50 [1] IRQ3 -> 0:3
Oct 5 01:34:50 [1] IRQ4 -> 0:4
Oct 5 01:34:50 [1] IRQ5 -> 0:5
Oct 5 01:34:50 [1] IRQ6 -> 0:6
Oct 5 01:34:50 [1] IRQ7 -> 0:7
Oct 5 01:34:50 [1] IRQ8 -> 0:8
Oct 5 01:34:50 [1] IRQ9 -> 0:9
Oct 5 01:34:50 [1] IRQ10 -> 0:10
Oct 5 01:34:50 [1] IRQ11 -> 0:11
Oct 5 01:34:50 [1] IRQ12 -> 0:12
Oct 5 01:34:50 [1] IRQ13 -> 0:13
Oct 5 01:34:50 [1] IRQ14 -> 0:14
Oct 5 01:34:50 [1] IRQ15 -> 0:15
Oct 5 01:34:50 [2] done.
Oct 5 01:34:50 [2] pnp: PnP ACPI init
Oct 5 01:34:50 [2] ACPI: bus type pnp registered
Oct 5 01:34:50 [2] pnp: PnP ACPI: found 12 devices
Oct 5 01:34:50 [2] ACPI: ACPI bus type pnp unregistered
Oct 5 01:34:50 [2] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
Oct 5 01:34:50 [2] system 00:0a: ioport range 0x400-0x47f has been reserved
Oct 5 01:34:50 [2] system 00:0a: ioport range 0x680-0x6ff has been reserved
Oct 5 01:34:50 [2] system 00:0a: ioport range 0x500-0x53f has been reserved
Oct 5 01:34:50 [2] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
Oct 5 01:34:50 [2] system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
Oct 5 01:34:50 [2] system 00:0a: iomem range 0xfed20000-0xfed9ffff has been reserved
Oct 5 01:34:50 [2] system 00:0b: iomem range 0x0-0x9ffff could not be reserved
Oct 5 01:34:50 [2] system 00:0b: iomem range 0xc0000-0xdffff could not be reserved
Oct 5 01:34:50 [2] system 00:0b: iomem range 0xe0000-0xfffff could not be reserved
Oct 5 01:34:50 [2] system 00:0b: iomem range 0x100000-0x1effffff could not be reserved
Oct 5 01:34:50 [2] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
Oct 5 01:34:50 [2] pci 0000:00:1e.0: IO window: 0xb000-0xbfff
Oct 5 01:34:50 [2] pci 0000:00:1e.0: MEM window: 0xff000000-0xff8fffff
Oct 5 01:34:50 [2] pci 0000:00:1e.0: PREFETCH window: 0x000000e6a00000-0x000000e6afffff
Oct 5 01:34:50 [1] pci 0000:00:1e.0: setting latency timer to 64
Oct 5 01:34:50 [1] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
Oct 5 01:34:50 [1] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
Oct 5 01:34:50 [1] pci_bus 0000:01: resource 0 io: [0xb000-0xbfff]
Oct 5 01:34:50 [1] pci_bus 0000:01: resource 1 mem: [0xff000000-0xff8fffff]
Oct 5 01:34:50 [1] pci_bus 0000:01: resource 2 pref mem [0xe6a00000-0xe6afffff]
Oct 5 01:34:50 [1] pci_bus 0000:01: resource 3 io: [0x00-0xffff]
Oct 5 01:34:50 [1] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffff]
Oct 5 01:34:50 [2] NET: Registered protocol family 2
Oct 5 01:34:50 [2] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Oct 5 01:34:50 [2] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
Oct 5 01:34:50 [2] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Oct 5 01:34:50 [2] TCP: Hash tables configured (established 16384 bind 16384)
Oct 5 01:34:50 [2] TCP reno registered
Oct 5 01:34:50 [2] NET: Registered protocol family 1
Oct 5 01:34:50 [2] Trying to unpack rootfs image as initramfs.
Oct 5 01:34:50 [2] rootfs image is not initramfs (junk in compressed archive); looks like an initrd
Oct 5 01:34:50 [2] Freeing initrd memory: 8930k freed
Oct 5 01:34:50 [2] Installing knfsd (copyright (C) 1996
okir@monad.swb.de).
Oct 5 01:34:50 [2] msgmni has been set to 975
Oct 5 01:34:50 [2] io scheduler noop registered (default)
Oct 5 01:34:50 [1] pci 0000:00:02.0: Boot video device
Oct 5 01:34:50 [4] pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling
Oct 5 01:34:50 [2] brd: module loaded
Oct 5 01:34:50 [2] loop: module loaded
Oct 5 01:34:50 [2] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
Oct 5 01:34:50 [2] serio: i8042 KBD port at 0x60,0x64 irq 1
Oct 5 01:34:50 [2] serio: i8042 AUX port at 0x60,0x64 irq 12
Oct 5 01:34:50 [2] mice: PS/2 mouse device common for all mice
Oct 5 01:34:50 [2] cpuidle: using governor ladder
Oct 5 01:34:50 [2] TCP cubic registered
Oct 5 01:34:50 [2] RPC: Registered udp transport module.
Oct 5 01:34:50 [2] RPC: Registered tcp transport module.
Oct 5 01:34:50 [2] Using IPI Shortcut mode
Oct 5 01:34:50 [2] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
Oct 5 01:34:50 [3] RAMDISK: CORE3 root image found at block 0
Oct 5 01:34:50 [4] EXT2-fs warning: checktime reached, running e2fsck is recommended
Oct 5 01:34:50 [4] VFS: Mounted root (ext2 filesystem) on device 1:0.
Oct 5 01:34:50 [2] Freeing unused kernel memory: 208k freed
Oct 5 01:34:50 [2] Floppy drive(s): fd0 is 1.44M
Oct 5 01:34:50 [2] FDC 0 is a National Semiconductor PC87306
Oct 5 01:34:51 [2] rtc_cmos 00:02: RTC can wake from S4
Oct 5 01:34:51 [2] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
Oct 5 01:34:51 [2] rtc0: alarms up to one month, 114 bytes nvram
Oct 5 01:34:52 [2] input: PC Speaker as /devices/platform/pcspkr/input/input1
Oct 5 01:34:53 [2] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
Oct 5 01:34:53 [2] ACPI: Power Button [PWRF]
Oct 5 01:34:53 [2] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
Oct 5 01:34:53 [2] ACPI: Sleep Button [SLPB]
Oct 5 01:34:53 [2] processor ACPI_CPU:00: registered as cooling_device0
Oct 5 01:34:53 [2] ACPI: Processor [CPU1] (supports 8 throttling states)
Oct 5 01:34:53 [2] usbcore: registered new interface driver usbfs
Oct 5 01:34:53 [2] usbcore: registered new interface driver hub
Oct 5 01:34:53 [2] usbcore: registered new device driver usb
Oct 5 01:34:53 [2] uhci_hcd: USB Universal Host Controller Interface driver
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Oct 5 01:34:53 [1] uhci_hcd 0000:00:1d.0: setting latency timer to 64
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.0: UHCI Host Controller
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000c800
Oct 5 01:34:53 [2] usb usb1: configuration #1 chosen from 1 choice
Oct 5 01:34:53 [2] hub 1-0:1.0: USB hub found
Oct 5 01:34:53 [2] hub 1-0:1.0: 2 ports detected
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
Oct 5 01:34:53 [1] uhci_hcd 0000:00:1d.1: setting latency timer to 64
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.1: UHCI Host Controller
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000cc00
Oct 5 01:34:53 [2] usb usb2: configuration #1 chosen from 1 choice
Oct 5 01:34:53 [2] hub 2-0:1.0: USB hub found
Oct 5 01:34:53 [2] hub 2-0:1.0: 2 ports detected
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Oct 5 01:34:53 [1] uhci_hcd 0000:00:1d.2: setting latency timer to 64
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.2: UHCI Host Controller
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d000
Oct 5 01:34:53 [2] usb usb3: configuration #1 chosen from 1 choice
Oct 5 01:34:53 [2] hub 3-0:1.0: USB hub found
Oct 5 01:34:53 [2] hub 3-0:1.0: 2 ports detected
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Oct 5 01:34:53 [1] uhci_hcd 0000:00:1d.3: setting latency timer to 64
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.3: UHCI Host Controller
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d400
Oct 5 01:34:53 [2] usb usb4: configuration #1 chosen from 1 choice
Oct 5 01:34:53 [2] hub 4-0:1.0: USB hub found
Oct 5 01:34:53 [2] hub 4-0:1.0: 2 ports detected
Oct 5 01:34:53 [2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Oct 5 01:34:53 [4] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
Oct 5 01:34:53 [1] ehci_hcd 0000:00:1d.7: setting latency timer to 64
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: EHCI Host Controller
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: debug port 1
Oct 5 01:34:53 [1] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa7fc00
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
Oct 5 01:34:53 [2] usb usb5: configuration #1 chosen from 1 choice
Oct 5 01:34:53 [2] hub 5-0:1.0: USB hub found
Oct 5 01:34:53 [2] hub 5-0:1.0: 8 ports detected
Oct 5 01:34:53 [3] SCSI subsystem initialized
Oct 5 01:34:53 [1] libata version 3.00 loaded.
Oct 5 01:34:53 [2] sata_mv 0000:01:00.0: version 1.28
Oct 5 01:34:53 [2] sata_mv 0000:01:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
Oct 5 01:34:53 [2] sata_mv 0000:01:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
Oct 5 01:34:53 [2] scsi0 : sata_mv
Oct 5 01:34:53 [2] scsi1 : sata_mv
Oct 5 01:34:53 [2] scsi2 : sata_mv
Oct 5 01:34:53 [2] scsi3 : sata_mv
Oct 5 01:34:53 [2] ata1: SATA max UDMA/133 mmio m1048576@0xff800000 port 0xff822000 irq 21
Oct 5 01:34:53 [2] ata2: SATA max UDMA/133 mmio m1048576@0xff800000 port 0xff824000 irq 21
Oct 5 01:34:53 [2] ata3: SATA max UDMA/133 mmio m1048576@0xff800000 port 0xff826000 irq 21
Oct 5 01:34:53 [2] ata4: SATA max UDMA/133 mmio m1048576@0xff800000 port 0xff828000 irq 21
Oct 5 01:34:53 [2] sata_mv 0000:01:01.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
Oct 5 01:34:53 [2] sata_mv 0000:01:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
Oct 5 01:34:53 [2] scsi4 : sata_mv
Oct 5 01:34:53 [2] scsi5 : sata_mv
Oct 5 01:34:53 [2] scsi6 : sata_mv
Oct 5 01:34:53 [2] scsi7 : sata_mv
Oct 5 01:34:53 [2] ata5: SATA max UDMA/133 mmio m1048576@0xff600000 port 0xff622000 irq 22
Oct 5 01:34:53 [2] ata6: SATA max UDMA/133 mmio m1048576@0xff600000 port 0xff624000 irq 22
Oct 5 01:34:53 [2] ata7: SATA max UDMA/133 mmio m1048576@0xff600000 port 0xff626000 irq 22
Oct 5 01:34:53 [2] ata8: SATA max UDMA/133 mmio m1048576@0xff600000 port 0xff628000 irq 22
Oct 5 01:34:53 [2] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Oct 5 01:34:53 [2] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:53 [2] ata1.00: ATA-6: ST3160827AS, 3.42, max UDMA/133
Oct 5 01:34:53 [2] ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:53 [2] ata5.00: ATA-8: WDC WD10EARS-00MVWB0, 50.0AB50, max UDMA/133
Oct 5 01:34:53 [2] ata5.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:53 [2] ata1.00: configured for UDMA/133
Oct 5 01:34:53 [3] scsi 0:0:0:0: Direct-Access ATA ST3160827AS 3.42 PQ: 0 ANSI: 5
Oct 5 01:34:53 [2] ata5.00: configured for UDMA/133
Oct 5 01:34:54 [2] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:54 [2] ata2.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Oct 5 01:34:54 [2] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:54 [2] ata2.00: configured for UDMA/133
Oct 5 01:34:54 [3] scsi 1:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Oct 5 01:34:54 [2] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:54 [2] ata3.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Oct 5 01:34:54 [2] ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:54 [2] ata3.00: configured for UDMA/133
Oct 5 01:34:54 [3] scsi 2:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Oct 5 01:34:55 [2] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:55 [2] ata4.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Oct 5 01:34:55 [2] ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:55 [2] ata4.00: configured for UDMA/133
Oct 5 01:34:55 [3] scsi 3:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Oct 5 01:34:55 [3] scsi 4:0:0:0: Direct-Access ATA WDC WD10EARS-00M 50.0 PQ: 0 ANSI: 5
Oct 5 01:34:55 [2] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:55 [2] ata6.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Oct 5 01:34:55 [2] ata6.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:55 [2] ata6.00: configured for UDMA/133
Oct 5 01:34:55 [3] scsi 5:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Oct 5 01:34:56 [2] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:56 [2] ata7.00: ATA-8: WDC WD20EARS-00MVWB0, 50.0AB50, max UDMA/133
Oct 5 01:34:56 [2] ata7.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:56 [2] ata7.00: configured for UDMA/133
Oct 5 01:34:56 [3] scsi 6:0:0:0: Direct-Access ATA WDC WD20EARS-00M 50.0 PQ: 0 ANSI: 5
Oct 5 01:34:56 [2] ata8: SATA link down (SStatus 0 SControl 300)
Oct 5 01:34:56 [2] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
Oct 5 01:34:56 [2] e100: Copyright(c) 1999-2006 Intel Corporation
Oct 5 01:34:56 [2] e100 0000:01:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
Oct 5 01:34:56 [2] e100 0000:01:08.0: PME# disabled
Oct 5 01:34:56 [2] e100: eth0: e100_probe: addr 0xff4ff000, irq 20, MAC addr 00:0c:f1:e0:83:4c
Oct 5 01:34:56 [2] Uniform Multi-Platform E-IDE driver
Oct 5 01:34:56 [2] piix 0000:00:1f.1: IDE controller (0x8086:0x24db rev 0x02)
Oct 5 01:34:56 [2] PIIX_IDE 0000:00:1f.1: enabling device (0005 -> 0007)
Oct 5 01:34:56 [2] PIIX_IDE 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Oct 5 01:34:56 [2] piix 0000:00:1f.1: not 100% native mode: will probe irqs later
Oct 5 01:34:56 [2] ide0: BM-DMA at 0xffa0-0xffa7
Oct 5 01:34:56 [2] ide1: BM-DMA at 0xffa8-0xffaf
Oct 5 01:34:56 [1] Probing IDE interface ide0.
Oct 5 01:34:57 [2] hda: Optiarc DVD RW AD-7200A, ATAPI CD/DVD-ROM drive
Oct 5 01:34:58 [1] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
Oct 5 01:34:58 [4] hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
Oct 5 01:34:58 [2] hda: UDMA/33 mode selected
Oct 5 01:34:58 [1] Probing IDE interface ide1.
Oct 5 01:34:58 [2] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Oct 5 01:34:58 [2] ide1 at 0x170-0x177,0x376 on irq 15
Oct 5 01:34:58 [1] ata_piix 0000:00:1f.2: version 2.13
Oct 5 01:34:58 [2] ata_piix 0000:00:1f.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Oct 5 01:34:58 [2] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
Oct 5 01:34:58 [1] ata_piix 0000:00:1f.2: setting latency timer to 64
Oct 5 01:34:58 [2] scsi8 : ata_piix
Oct 5 01:34:58 [2] scsi9 : ata_piix
Oct 5 01:34:58 [2] ata9: SATA max UDMA/133 cmd 0xe800 ctl 0xe400 bmdma 0xd800 irq 18
Oct 5 01:34:58 [2] ata10: SATA max UDMA/133 cmd 0xe000 ctl 0xdc00 bmdma 0xd808 irq 18
Oct 5 01:34:58 [2] ata9.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
Oct 5 01:34:58 [2] ata9.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
Oct 5 01:34:58 [2] ata9.00: configured for UDMA/133
Oct 5 01:34:58 [3] scsi 8:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0 ANSI: 5
Oct 5 01:34:59 [2] ata10.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Oct 5 01:34:59 [2] ata10.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
Oct 5 01:34:59 [2] ata10.00: configured for UDMA/133
Oct 5 01:34:59 [3] scsi 9:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Oct 5 01:35:00 [4] Driver 'sd' needs updating - please use bus_type methods
Oct 5 01:35:00 [3] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
Oct 5 01:35:00 [3] sd 0:0:0:0: [sda] Write Protect is off
Oct 5 01:35:00 [1] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sda:<5>sd 1:0:0:0: [sdb] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 1:0:0:0: [sdb] Write Protect is off
Oct 5 01:35:00 [1] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdb:<5>sd 2:0:0:0: [sdc] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 2:0:0:0: [sdc] Write Protect is off
Oct 5 01:35:00 [1] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdc:<5>sd 3:0:0:0: [sdd] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 3:0:0:0: [sdd] Write Protect is off
Oct 5 01:35:00 [1] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdd:
Oct 5 01:35:00 [3] sd 4:0:0:0: [sde] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
Oct 5 01:35:00 [3] sd 4:0:0:0: [sde] Write Protect is off
Oct 5 01:35:00 [1] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sde:<5>sd 5:0:0:0: [sdf] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 5:0:0:0: [sdf] Write Protect is off
Oct 5 01:35:00 [1] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdf:<5>sd 6:0:0:0: [sdg] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 6:0:0:0: [sdg] Write Protect is off
Oct 5 01:35:00 [1] sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdg:<5>sd 8:0:0:0: [sdh] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
Oct 5 01:35:00 [3] sd 8:0:0:0: [sdh] Write Protect is off
Oct 5 01:35:00 [1] sd 8:0:0:0: [sdh] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 8:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdh:<5>sd 9:0:0:0: [sdi] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 9:0:0:0: [sdi] Write Protect is off
Oct 5 01:35:00 [1] sd 9:0:0:0: [sdi] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 9:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdi:
Oct 5 01:35:00 [2] sda1
Oct 5 01:35:00 [3] sd 0:0:0:0: [sda] Attached SCSI disk
Oct 5 01:35:00 [4] sdb1
Oct 5 01:35:00 [4] sde1
Oct 5 01:35:00 [4] sdc1
Oct 5 01:35:00 [4] sdf1
Oct 5 01:35:00 [3] sd 1:0:0:0: [sdb] Attached SCSI disk
Oct 5 01:35:00 [3] sd 4:0:0:0: [sde] Attached SCSI disk
Oct 5 01:35:00 [3] sd 2:0:0:0: [sdc] Attached SCSI disk
Oct 5 01:35:00 [3] sd 5:0:0:0: [sdf] Attached SCSI disk
Oct 5 01:35:00 [4] sdd1
Oct 5 01:35:00 [3] sd 3:0:0:0: [sdd] Attached SCSI disk
Oct 5 01:35:00 [4] sdg1
Oct 5 01:35:00 [3] sd 6:0:0:0: [sdg] Attached SCSI disk
Oct 5 01:35:00 [4] sdi1
Oct 5 01:35:00 [4] sdh1
Oct 5 01:35:00 [3] sd 9:0:0:0: [sdi] Attached SCSI disk
Oct 5 01:35:00 [3] sd 8:0:0:0: [sdh] Attached SCSI disk
Oct 5 01:35:00 [2] ide-cd driver 5.00
Oct 5 01:35:00 [2] ide-cd: hda: ATAPI 48X DVD-ROM DVD-R/RAM CD-R/RW drive, 2048kB Cache
Oct 5 01:35:00 [2] Uniform CD-ROM driver Revision: 3.20
Oct 5 01:35:56 [2] e100: eth0 NIC Link is Up 100 Mbps Full Duplex
Oct 5 01:43:48 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:48 [2] EXT3 FS on sdb1, internal journal
Oct 5 01:43:48 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:49 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:49 [2] EXT3 FS on sdc1, internal journal
Oct 5 01:43:49 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:49 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:49 [2] EXT3 FS on sdd1, internal journal
Oct 5 01:43:49 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:49 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:49 [2] EXT3 FS on sde1, internal journal
Oct 5 01:43:49 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:50 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:50 [2] EXT3 FS on sdf1, internal journal
Oct 5 01:43:50 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:51 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:51 [2] EXT3 FS on sdg1, internal journal
Oct 5 01:43:51 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:51 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:51 [2] EXT3 FS on sdh1, internal journal
Oct 5 01:43:51 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:51 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:51 [2] EXT3 FS on sdi1, internal journal
Oct 5 01:43:51 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:44:24 [2] Adding 999416k swap on /export/Disk-4/_NL_SWAP/VRAM. Priority:-1 extents:254 across:1017068k
Oct 5 02:26:15 [2] warning: `smbd' uses 32-bit capabilities (legacy support in use)