NASLite Network Attached Storage

Can someone please give me step by step instructions for removing a mirror (1 or all)

I've looked everywhere for months and months and I can't seem to find a way to do it.

Cheers, Mark.

If anyone could also point me in the direction for understanding the syslogs that would also be appreciated.

I had a drive that was slowly failing for the last few weeks and I could not for the life of me work out which one it was from the logs.

Many thanks.

Hi

It is very easy. Login via telnet to NL. Option 3 - Storage config then choose the option 0, 1 or 2 etc for the disk which has the mirror information(s), Option 9 - Mirror to ... Hit enter on an empty Mirror > line, NL will ask if you want to cancel mirror, answer Yes. Repeat for all drives that you want to clear the Mirror commands.

That all folks

Thanks Robrub!!!

I've been typing all sorts of things at the prompt - never thought of just hitting enter.

I've wasted so much time trying to figure that out... sheesh! I should have asked the question here a lot sooner.

Your help is much appreciated.

Now if I could only get my syslog question answered...

Hi again

You have to be much more specific and verbose than a drive slowly failing... What are the symptoms ? Any info on the sys log ?

Robby

Or even post your syslog for us to look at and maybe someone will be able to point you in the right direction!

You could also look at the drive info on the service pages and that might give you a clue also.

HTH Doug

Thanks for your help!

I'll post the Syslog below (made after failed drive was replaced - it doesn't show the Syslog before the drive failure; I didn't think to copy and paste it out).

I suppose I need to reframe the earlier question about the Syslog; Where can I go or how can I get the information that will give me the ability to learn how to read the Syslogs for myself? I've look everywhere on the net and ServerElements site without much luck.

I don't know a lot about Linux; is this why I can't understand the Syslog?

Thanks again for your help, it's much appreciated.

Oct 5 01:34:50 [3] klogd started: BusyBox v1.12.1 (2009-11-19 21:21:30 UTC)
Oct 5 01:34:50 [3] Linux version 2.6.30.3.CORE3 (root@DevBox) (gcc version 4.1.2 (SE 4.1.2 p1.0.2)) #1 Wed Jul 14 01:02:59 UTC 2010
Oct 5 01:34:50 [2] KERNEL supported cpus:
Oct 5 01:34:50 [2] Intel GenuineIntel
Oct 5 01:34:50 [2] AMD AuthenticAMD
Oct 5 01:34:50 [2] NSC Geode by NSC
Oct 5 01:34:50 [2] Cyrix CyrixInstead
Oct 5 01:34:50 [2] Centaur CentaurHauls
Oct 5 01:34:50 [2] Transmeta GenuineTMx86
Oct 5 01:34:50 [2] Transmeta TransmetaCPU
Oct 5 01:34:50 [2] UMC UMC UMC UMC
Oct 5 01:34:50 [2] BIOS-provided physical RAM map:
Oct 5 01:34:50 [2] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Oct 5 01:34:50 [2] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Oct 5 01:34:50 [2] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
Oct 5 01:34:50 [2] BIOS-e820: 0000000000100000 - 000000001ef2fc00 (usable)
Oct 5 01:34:50 [2] BIOS-e820: 000000001ef2fc00 - 000000001ef30000 (ACPI NVS)
Oct 5 01:34:50 [2] BIOS-e820: 000000001ef30000 - 000000001ef40000 (ACPI data)
Oct 5 01:34:50 [2] BIOS-e820: 000000001ef40000 - 000000001eff0000 (ACPI NVS)
Oct 5 01:34:50 [2] BIOS-e820: 000000001eff0000 - 000000001f000000 (reserved)
Oct 5 01:34:50 [2] BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved)
Oct 5 01:34:50 [2] BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
Oct 5 01:34:50 [2] DMI 2.3 present.
Oct 5 01:34:50 [2] last_pfn = 0x1ef2f max_arch_pfn = 0x100000
Oct 5 01:34:50 [2] init_memory_mapping: 0000000000000000-000000001ef2f000
Oct 5 01:34:50 [1] 0000000000 - 0000400000 page 4k
Oct 5 01:34:50 [1] 0000400000 - 001ec00000 page 2M
Oct 5 01:34:50 [1] 001ec00000 - 001ef2f000 page 4k
Oct 5 01:34:50 [1] kernel direct mapping tables up to 1ef2f000 @ 7000-c000
Oct 5 01:34:50 [2] RAMDISK: 1e656000 - 1ef0e93a
Oct 5 01:34:50 [4] ACPI: RSDP 000f61b0 00014 (v00 ACPIAM)
Oct 5 01:34:50 [4] ACPI: RSDT 1ef30000 00038 (v01 INTEL D865GLC 20040421 MSFT 00000097)
Oct 5 01:34:50 [4] ACPI: FACP 1ef30200 00081 (v02 INTEL D865GLC 20040421 MSFT 00000097)
Oct 5 01:34:50 [4] ACPI: DSDT 1ef30370 04231 (v01 INTEL D865GLC 00000001 MSFT 0100000D)
Oct 5 01:34:50 [4] ACPI: FACS 1ef40000 00040
Oct 5 01:34:50 [4] ACPI: APIC 1ef30300 00068 (v01 INTEL D865GLC 20040421 MSFT 00000097)
Oct 5 01:34:50 [4] ACPI: ASF! 1ef345b0 00099 (v16 LEGEND I865PASF 00000001 MSFT 0100000D)
Oct 5 01:34:50 [4] ACPI: TCPA 1ef34649 00034 (v01 INTEL TBLOEMID 00000001 MSFT 00000097)
Oct 5 01:34:50 [4] ACPI: WDDT 1ef3467d 00040 (v01 INTEL OEMWDDT 00000001 MSFT 0100000D)
Oct 5 01:34:50 [1] ACPI: Local APIC address 0xfee00000
Oct 5 01:34:50 [3] 0MB HIGHMEM available.
Oct 5 01:34:50 [3] 495MB LOWMEM available.
Oct 5 01:34:50 [2] mapped low ram: 0 - 1ef2f000
Oct 5 01:34:50 [2] low ram: 0 - 1ef2f000
Oct 5 01:34:50 [2] node 0 low ram: 00000000 - 1ef2f000
Oct 5 01:34:50 [2] node 0 bootmap 00001000 - 00004de8
Oct 5 01:34:50 [2] (7 early reservations) ==> bootmem [0000000000 - 001ef2f000]
Oct 5 01:34:50 [2] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
Oct 5 01:34:50 [2] #1 [0000100000 - 000039b83c] TEXT DATA BSS ==> [0000100000 - 000039b83c]
Oct 5 01:34:50 [2] #2 [001e656000 - 001ef0e93a] RAMDISK ==> [001e656000 - 001ef0e93a]
Oct 5 01:34:50 [2] #3 [000009a000 - 0000100000] BIOS reserved ==> [000009a000 - 0000100000]
Oct 5 01:34:50 [2] #4 [000039c000 - 000039e18c] BRK ==> [000039c000 - 000039e18c]
Oct 5 01:34:50 [2] #5 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
Oct 5 01:34:50 [2] #6 [0000001000 - 0000005000] BOOTMAP ==> [0000001000 - 0000005000]
Oct 5 01:34:50 [2] found SMP MP-table at [c00ff780] ff780
Oct 5 01:34:50 [4] Zone PFN ranges:
Oct 5 01:34:50 [4] DMA 0x00000000 -> 0x00001000
Oct 5 01:34:50 [4] Normal 0x00001000 -> 0x0001ef2f
Oct 5 01:34:50 [4] HighMem 0x0001ef2f -> 0x0001ef2f
Oct 5 01:34:50 [4] Movable zone start PFN for each node
Oct 5 01:34:50 [4] early_node_map[2] active PFN ranges
Oct 5 01:34:50 [4] 0: 0x00000000 -> 0x0000009f
Oct 5 01:34:50 [4] 0: 0x00000100 -> 0x0001ef2f
Oct 5 01:34:50 [1] On node 0 totalpages: 126670
Oct 5 01:34:50 [1] free_area_init_node: node 0, pgdat c031d560, node_mem_map c1000000
Oct 5 01:34:50 [1] DMA zone: 32 pages used for memmap
Oct 5 01:34:50 [1] DMA zone: 0 pages reserved
Oct 5 01:34:50 [1] DMA zone: 3967 pages, LIFO batch:0
Oct 5 01:34:50 [1] Normal zone: 959 pages used for memmap
Oct 5 01:34:50 [1] Normal zone: 121712 pages, LIFO batch:31
Oct 5 01:34:50 [2] Using APIC driver default
Oct 5 01:34:50 [2] ACPI: PM-Timer IO Port: 0x408
Oct 5 01:34:50 [1] ACPI: Local APIC address 0xfee00000
Oct 5 01:34:50 [2] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Oct 5 01:34:50 [2] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Oct 5 01:34:50 [4] ACPI: NR_CPUS/possible_cpus limit of 1 reached. Processor 1/0x1 ignored.
Oct 5 01:34:50 [2] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
Oct 5 01:34:50 [2] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
Oct 5 01:34:50 [2] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
Oct 5 01:34:50 [2] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
Oct 5 01:34:50 [2] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Oct 5 01:34:50 [2] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Oct 5 01:34:50 [1] ACPI: IRQ0 used by override.
Oct 5 01:34:50 [1] ACPI: IRQ2 used by over
Oct 5 01:34:50 [2] ride.
Oct 5 01:34:50 [1] ACPI: IRQ9 used by override.
Oct 5 01:34:50 [2] Enabling APIC mode: Flat. Using 1 I/O APICs
Oct 5 01:34:50 [2] Using ACPI (MADT) for SMP configuration information
Oct 5 01:34:50 [1] nr_irqs_gsi: 24
Oct 5 01:34:50 [2] Allocating PCI resources starting at 20000000 (gap: 1f000000:dfcf0000)
Oct 5 01:34:50 [4] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125679
Oct 5 01:34:50 [3] Kernel command line: rw root=/dev/ram0 initrd=NASLite.02 quiet BOOT_IMAGE=NASLite.01
Oct 5 01:34:50 [2] Enabling fast FPU save and restore. done.
Oct 5 01:34:50 [2] Enabling unmasked SIMD FPU exception support. done.
Oct 5 01:34:50 [2] Initializing CPU#0
Oct 5 01:34:50 [2] NR_IRQS:288
Oct 5 01:34:50 [4] PID hash table entries: 2048 (order: 11, 8192 bytes)
Oct 5 01:34:50 [4] Fast TSC calibration using PIT
Oct 5 01:34:50 [4] Detected 2792.939 MHz processor.
Oct 5 01:34:50 [4] Console: colour VGA+ 80x25
Oct 5 01:34:50 [2] console [tty0] enabled
Oct 5 01:34:50 [2] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Oct 5 01:34:50 [2] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Oct 5 01:34:50 [2] Initializing HighMem for node 0 (00000000:00000000)
Oct 5 01:34:50 [2] Memory: 490336k/507068k available (1523k kernel code, 16016k reserved, 667k data, 208k init, 0k highmem)
Oct 5 01:34:50 [2] virtual kernel memory layout:
Oct 5 01:34:50 [2] fixmap : 0xfffa9000 - 0xfffff000 ( 344 kB)
Oct 5 01:34:50 [2] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
Oct 5 01:34:50 [2] vmalloc : 0xdf72f000 - 0xff7fe000 ( 512 MB)
Oct 5 01:34:50 [2] lowmem : 0xc0000000 - 0xdef2f000 ( 495 MB)
Oct 5 01:34:50 [2] .init : 0xc0326000 - 0xc035a000 ( 208 kB)
Oct 5 01:34:50 [2] .data : 0xc027cfdb - 0xc0323e14 ( 667 kB)
Oct 5 01:34:50 [2] .text : 0xc0100000 - 0xc027cfdb (1523 kB)
Oct 5 01:34:50 [2] Checking if this processor honours the WP bit even in supervisor mode.Ok.
Oct 5 01:34:50 [2] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Oct 5 01:34:50 [2] Calibrating delay loop (skipped), value calculated using timer frequency 5585.87 BogoMIPS (lpj=11171756)
Oct 5 01:34:50 [4] Mount-cache hash table entries: 512
Oct 5 01:34:50 [2] CPU: Trace cache: 12K uops, L1 D cache: 8K
Oct 5 01:34:50 [2] CPU: L2 cache: 512K
Oct 5 01:34:50 [4] CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Oct 5 01:34:50 [2] Checking 'hlt' instruction. OK.
Oct 5 01:34:50 [2] ACPI: Core revision 20090320
Oct 5 01:34:50 [2] net_namespace: 296 bytes
Oct 5 01:34:50 [2] NET: Registered protocol family 16
Oct 5 01:34:50 [2] ACPI: bus type pci registered
Oct 5 01:34:50 [2] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
Oct 5 01:34:50 [2] PCI: Using configuration type 1 for base access
Oct 5 01:34:50 [4] bio: create slab at 0
Oct 5 01:34:50 [1] ACPI: EC: Look up EC in DSDT
Oct 5 01:34:50 [2] ACPI: Interpreter enabled
Oct 5 01:34:50 [2] ACPI: (supports S0 S5)
Oct 5 01:34:50 [2] ACPI: Using IOAPIC for interrupt routing
Oct 5 01:34:50 [2] ACPI: Power Resource [URP1] (off)
Oct 5 01:34:50 [2] ACPI: Power Resource [FDDP] (off)
Oct 5 01:34:50 [2] ACPI: Power Resource [LPTP] (off)
Oct 5 01:34:50 [2] ACPI: No dock devices found.
Oct 5 01:34:50 [2] ACPI: PCI Root Bridge [PCI0] (0000:00)
Oct 5 01:34:50 [1] pci 0000:00:00.0: reg 10 32bit mmio: [0xf8000000-0xfbffffff]
Oct 5 01:34:50 [1] pci 0000:00:02.0: reg 10 32bit mmio: [0xf0000000-0xf7ffffff]
Oct 5 01:34:50 [1] pci 0000:00:02.0: reg 14 32bit mmio: [0xffa80000-0xffafffff]
Oct 5 01:34:50 [1] pci 0000:00:02.0: reg 18 io port: [0xec00-0xec07]
Oct 5 01:34:50 [1] pci 0000:00:1d.0: reg 20 io port: [0xc800-0xc81f]
Oct 5 01:34:50 [1] pci 0000:00:1d.1: reg 20 io port: [0xcc00-0xcc1f]
Oct 5 01:34:50 [1] pci 0000:00:1d.2: reg 20 io port: [0xd000-0xd01f]
Oct 5 01:34:50 [1] pci 0000:00:1d.3: reg 20 io port: [0xd400-0xd41f]
Oct 5 01:34:50 [1] pci 0000:00:1d.7: reg 10 32bit mmio: [0xffa7fc00-0xffa7ffff]
Oct 5 01:34:50 [2] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
Oct 5 01:34:50 [2] pci 0000:00:1d.7: PME# disabled
Oct 5 01:34:50 [2] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
Oct 5 01:34:50 [2] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH4 GPIO
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
Oct 5 01:34:50 [1] pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff]
Oct 5 01:34:50 [1] pci 0000:00:1f.2: reg 10 io port: [0xe800-0xe807]
Oct 5 01:34:50 [1] pci 0000:00:1f.2: reg 14 io port: [0xe400-0xe403]
Oct 5 01:34:50 [1] pci 0000:00:1f.2: reg 18 io port: [0xe000-0xe007]
Oct 5 01:34:50 [1] pci 0000:00:1f.2: reg 1c io port: [0xdc00-0xdc03]
Oct 5 01:34:50 [1] pci 0000:00:1f.2: reg 20 io port: [0xd800-0xd80f]
Oct 5 01:34:50 [1] pci 0000:00:1f.3: reg 20 io port: [0xc400-0xc41f]
Oct 5 01:34:50 [1] pci 0000:01:00.0: reg 10 64bit mmio: [0xff800000-0xff8fffff]
Oct 5 01:34:50 [1] pci 0000:01:00.0: reg 18 io port: [0xb800-0xb8ff]
Oct 5 01:34:50 [1] pci 0000:01:01.0: reg 10 64bit mmio: [0xff600000-0xff6fffff]
Oct 5 01:34:50 [1] pci 0000:01:01.0: reg 18 io port: [0xb400-0xb4ff]
Oct 5 01:34:50 [1] pci 0000:01:08.0: reg 10 32bit mmio: [0xff4ff000-0xff4fffff]
Oct 5 01:34:50 [1] pci 0000:01:08.0: reg 14 io port: [0xbc00-0xbc3f]
Oct 5 01:34:50 [1] pci 0000:01:08.0: supports D1 D2
Oct 5 01:34:50 [2] pci 0000:01:08.0: PME# supported from D0 D1 D2 D3hot D3cold
Oct 5 01:34:50 [2] pci 0000:01:08.0: PME# disabled
Oct 5 01:34:50 [2] pci 0000:00:1e.0: transparent bridge
Oct 5 01:34:50 [1] pci 0000:00:1e.0: bridge io port: [0xb000-0xbfff]
Oct 5 01:34:50 [1] pci 0000:00:1e.0: bridge 32bit mmio: [0xff000000-0xff8fffff]
Oct 5 01:34:50 [1] pci 0000:00:1e.0: bridge 32bit mmio pref: [0xe6a00000-0xe6afffff]
Oct 5 01:34:50 [1] pci_bus 0000:00: on NUMA node 0
Oct 5 01:34:50 [1] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Oct 5 01:34:50 [1] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 *4 5 6 7 9 10 11 12 14 15)
Oct 5 01:34:50 [2] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Oct 5 01:34:50 [2] PCI: Using ACPI for IRQ routing
Oct 5 01:34:50 [1]
Oct 5 01:34:50 [1] printing PIC contents
Oct 5 01:34:50 [1] . PIC IMR: ffff
Oct 5 01:34:50 [1] . PIC IRR: 0000
Oct 5 01:34:50 [1] . PIC ISR: 0000
Oct 5 01:34:50 [1] . PIC ELCR: 0eb8
Oct 5 01:34:50 [4]
Oct 5 01:34:50 [1] printing local APIC contents on CPU#0/0:
Oct 5 01:34:50 [2] . APIC ID: 00000000 (0)
Oct 5 01:34:50 [2] . APIC VERSION: 00050014
Oct 5 01:34:50 [1] . APIC TASKPRI: 00000000 (00)
Oct 5 01:34:50 [1] . APIC PROCPRI: 00000000
Oct 5 01:34:50 [1] . APIC LDR: 01000000
Oct 5 01:34:50 [1] . APIC DFR: ffffffff
Oct 5 01:34:50 [1] . APIC SPIV: 000001ff
Oct 5 01:34:50 [1] . APIC ISR field:
Oct 5 01:34:50 [1] 0123456789abcdef0123456789abcdef
Oct 5 01:34:50 [1] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [1] . APIC TMR field:
Oct 5 01:34:50 [1] 0123456789abcdef0123456789abcdef
Oct 5 01:34:50 [1] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [1] . APIC IRR field:
Oct 5 01:34:50 [1] 0123456789abcdef0123456789abcdef
Oct 5 01:34:50 [1] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [4] 00000000000000000000000000000000
Oct 5 01:34:50 [1] . APIC ESR: 00000000
Oct 5 01:34:50 [1] . APIC ICR: 00000630
Oct 5 01:34:50 [1] . APIC ICR2: 01000000
Oct 5 01:34:50 [1] . APIC LVTT: 000200ef
Oct 5 01:34:50 [1] . APIC LVTPC: 00010000
Oct 5 01:34:50 [1] . APIC LVT0: 00010700
Oct 5 01:34:50 [1] . APIC LVT1: 00000400
Oct 5 01:34:50 [1] . APIC LVTERR: 000000fe
Oct 5 01:34:50 [1] . APIC TMICT: 0000c2d5
Oct 5 01:34:50 [1] . APIC TMCCT: 000075c5
Oct 5 01:34:50 [1] . APIC TDCR: 00000003
Oct 5 01:34:50 [4]
Oct 5 01:34:50 [1] number of MP IRQ sources: 15.
Oct 5 01:34:50 [1] number of IO-APIC #2 registers: 24.
Oct 5 01:34:50 [2] testing the IO APIC.
Oct 5 01:34:50 [4]
Oct 5 01:34:50 [1] IO APIC #2
Oct 5 01:34:50 [1] register #00: 02000000
Oct 5 01:34:50 [1] . : physical APIC id: 02
Oct 5 01:34:50 [1] . : Delivery Type: 0
Oct 5 01:34:50 [1] . : LTS : 0
Oct 5 01:34:50 [1] register #01: 00178020
Oct 5 01:34:50 [1] . : max redirection entries: 0017
Oct 5 01:34:50 [1] . : PRQ implemented: 1
Oct 5 01:34:50 [1] . : IO APIC version: 0020
Oct 5 01:34:50 [1] IRQ redirection table:
Oct 5 01:34:50 [1] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
Oct 5 01:34:50 [1] 00 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 01 001 0 0 0 0 0 1 1 31
Oct 5 01:34:50 [1] 02 001 0 0 0 0 0 1 1 30
Oct 5 01:34:50 [1] 03 001 0 0 0 0 0 1 1 33
Oct 5 01:34:50 [1] 04 001 0 0 0 0 0 1 1 34
Oct 5 01:34:50 [1] 05 001 0 0 0 0 0 1 1 35
Oct 5 01:34:50 [1] 06 001 0 0 0 0 0 1 1 36
Oct 5 01:34:50 [1] 07 001 0 0 0 0 0 1 1 37
Oct 5 01:34:50 [1] 08 001 0 0 0 0 0 1 1 38
Oct 5 01:34:50 [1] 09 001 0 1 0 0 0 1 1 39
Oct 5 01:34:50 [1] 0a 001 0 0 0 0 0 1 1 3A
Oct 5 01:34:50 [1] 0b 001 0 0 0 0 0 1 1 3B
Oct 5 01:34:50 [1] 0c 001 0 0 0 0 0 1 1 3C
Oct 5 01:34:50 [1] 0d 001 0 0 0 0 0
Oct 5 01:34:50 [2] 1 1 3D
Oct 5 01:34:50 [1] 0e 001 0 0 0 0 0 1 1 3E
Oct 5 01:34:50 [1] 0f 001 0 0 0 0 0 1 1 3F
Oct 5 01:34:50 [1] 10 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 11 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 12 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 13 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 14 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 15 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 16 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] 17 000 1 0 0 0 0 0 0 00
Oct 5 01:34:50 [1] IRQ to pin mappings:
Oct 5 01:34:50 [1] IRQ0 -> 0:2
Oct 5 01:34:50 [1] IRQ1 -> 0:1
Oct 5 01:34:50 [1] IRQ3 -> 0:3
Oct 5 01:34:50 [1] IRQ4 -> 0:4
Oct 5 01:34:50 [1] IRQ5 -> 0:5
Oct 5 01:34:50 [1] IRQ6 -> 0:6
Oct 5 01:34:50 [1] IRQ7 -> 0:7
Oct 5 01:34:50 [1] IRQ8 -> 0:8
Oct 5 01:34:50 [1] IRQ9 -> 0:9
Oct 5 01:34:50 [1] IRQ10 -> 0:10
Oct 5 01:34:50 [1] IRQ11 -> 0:11
Oct 5 01:34:50 [1] IRQ12 -> 0:12
Oct 5 01:34:50 [1] IRQ13 -> 0:13
Oct 5 01:34:50 [1] IRQ14 -> 0:14
Oct 5 01:34:50 [1] IRQ15 -> 0:15
Oct 5 01:34:50 [2] done.
Oct 5 01:34:50 [2] pnp: PnP ACPI init
Oct 5 01:34:50 [2] ACPI: bus type pnp registered
Oct 5 01:34:50 [2] pnp: PnP ACPI: found 12 devices
Oct 5 01:34:50 [2] ACPI: ACPI bus type pnp unregistered
Oct 5 01:34:50 [2] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
Oct 5 01:34:50 [2] system 00:0a: ioport range 0x400-0x47f has been reserved
Oct 5 01:34:50 [2] system 00:0a: ioport range 0x680-0x6ff has been reserved
Oct 5 01:34:50 [2] system 00:0a: ioport range 0x500-0x53f has been reserved
Oct 5 01:34:50 [2] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
Oct 5 01:34:50 [2] system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
Oct 5 01:34:50 [2] system 00:0a: iomem range 0xfed20000-0xfed9ffff has been reserved
Oct 5 01:34:50 [2] system 00:0b: iomem range 0x0-0x9ffff could not be reserved
Oct 5 01:34:50 [2] system 00:0b: iomem range 0xc0000-0xdffff could not be reserved
Oct 5 01:34:50 [2] system 00:0b: iomem range 0xe0000-0xfffff could not be reserved
Oct 5 01:34:50 [2] system 00:0b: iomem range 0x100000-0x1effffff could not be reserved
Oct 5 01:34:50 [2] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
Oct 5 01:34:50 [2] pci 0000:00:1e.0: IO window: 0xb000-0xbfff
Oct 5 01:34:50 [2] pci 0000:00:1e.0: MEM window: 0xff000000-0xff8fffff
Oct 5 01:34:50 [2] pci 0000:00:1e.0: PREFETCH window: 0x000000e6a00000-0x000000e6afffff
Oct 5 01:34:50 [1] pci 0000:00:1e.0: setting latency timer to 64
Oct 5 01:34:50 [1] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
Oct 5 01:34:50 [1] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
Oct 5 01:34:50 [1] pci_bus 0000:01: resource 0 io: [0xb000-0xbfff]
Oct 5 01:34:50 [1] pci_bus 0000:01: resource 1 mem: [0xff000000-0xff8fffff]
Oct 5 01:34:50 [1] pci_bus 0000:01: resource 2 pref mem [0xe6a00000-0xe6afffff]
Oct 5 01:34:50 [1] pci_bus 0000:01: resource 3 io: [0x00-0xffff]
Oct 5 01:34:50 [1] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffff]
Oct 5 01:34:50 [2] NET: Registered protocol family 2
Oct 5 01:34:50 [2] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Oct 5 01:34:50 [2] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
Oct 5 01:34:50 [2] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Oct 5 01:34:50 [2] TCP: Hash tables configured (established 16384 bind 16384)
Oct 5 01:34:50 [2] TCP reno registered
Oct 5 01:34:50 [2] NET: Registered protocol family 1
Oct 5 01:34:50 [2] Trying to unpack rootfs image as initramfs.
Oct 5 01:34:50 [2] rootfs image is not initramfs (junk in compressed archive); looks like an initrd
Oct 5 01:34:50 [2] Freeing initrd memory: 8930k freed
Oct 5 01:34:50 [2] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Oct 5 01:34:50 [2] msgmni has been set to 975
Oct 5 01:34:50 [2] io scheduler noop registered (default)
Oct 5 01:34:50 [1] pci 0000:00:02.0: Boot video device
Oct 5 01:34:50 [4] pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling
Oct 5 01:34:50 [2] brd: module loaded
Oct 5 01:34:50 [2] loop: module loaded
Oct 5 01:34:50 [2] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
Oct 5 01:34:50 [2] serio: i8042 KBD port at 0x60,0x64 irq 1
Oct 5 01:34:50 [2] serio: i8042 AUX port at 0x60,0x64 irq 12
Oct 5 01:34:50 [2] mice: PS/2 mouse device common for all mice
Oct 5 01:34:50 [2] cpuidle: using governor ladder
Oct 5 01:34:50 [2] TCP cubic registered
Oct 5 01:34:50 [2] RPC: Registered udp transport module.
Oct 5 01:34:50 [2] RPC: Registered tcp transport module.
Oct 5 01:34:50 [2] Using IPI Shortcut mode
Oct 5 01:34:50 [2] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
Oct 5 01:34:50 [3] RAMDISK: CORE3 root image found at block 0
Oct 5 01:34:50 [4] EXT2-fs warning: checktime reached, running e2fsck is recommended
Oct 5 01:34:50 [4] VFS: Mounted root (ext2 filesystem) on device 1:0.
Oct 5 01:34:50 [2] Freeing unused kernel memory: 208k freed
Oct 5 01:34:50 [2] Floppy drive(s): fd0 is 1.44M
Oct 5 01:34:50 [2] FDC 0 is a National Semiconductor PC87306
Oct 5 01:34:51 [2] rtc_cmos 00:02: RTC can wake from S4
Oct 5 01:34:51 [2] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
Oct 5 01:34:51 [2] rtc0: alarms up to one month, 114 bytes nvram
Oct 5 01:34:52 [2] input: PC Speaker as /devices/platform/pcspkr/input/input1
Oct 5 01:34:53 [2] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
Oct 5 01:34:53 [2] ACPI: Power Button [PWRF]
Oct 5 01:34:53 [2] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
Oct 5 01:34:53 [2] ACPI: Sleep Button [SLPB]
Oct 5 01:34:53 [2] processor ACPI_CPU:00: registered as cooling_device0
Oct 5 01:34:53 [2] ACPI: Processor [CPU1] (supports 8 throttling states)
Oct 5 01:34:53 [2] usbcore: registered new interface driver usbfs
Oct 5 01:34:53 [2] usbcore: registered new interface driver hub
Oct 5 01:34:53 [2] usbcore: registered new device driver usb
Oct 5 01:34:53 [2] uhci_hcd: USB Universal Host Controller Interface driver
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Oct 5 01:34:53 [1] uhci_hcd 0000:00:1d.0: setting latency timer to 64
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.0: UHCI Host Controller
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000c800
Oct 5 01:34:53 [2] usb usb1: configuration #1 chosen from 1 choice
Oct 5 01:34:53 [2] hub 1-0:1.0: USB hub found
Oct 5 01:34:53 [2] hub 1-0:1.0: 2 ports detected
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
Oct 5 01:34:53 [1] uhci_hcd 0000:00:1d.1: setting latency timer to 64
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.1: UHCI Host Controller
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000cc00
Oct 5 01:34:53 [2] usb usb2: configuration #1 chosen from 1 choice
Oct 5 01:34:53 [2] hub 2-0:1.0: USB hub found
Oct 5 01:34:53 [2] hub 2-0:1.0: 2 ports detected
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Oct 5 01:34:53 [1] uhci_hcd 0000:00:1d.2: setting latency timer to 64
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.2: UHCI Host Controller
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d000
Oct 5 01:34:53 [2] usb usb3: configuration #1 chosen from 1 choice
Oct 5 01:34:53 [2] hub 3-0:1.0: USB hub found
Oct 5 01:34:53 [2] hub 3-0:1.0: 2 ports detected
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Oct 5 01:34:53 [1] uhci_hcd 0000:00:1d.3: setting latency timer to 64
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.3: UHCI Host Controller
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
Oct 5 01:34:53 [2] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d400
Oct 5 01:34:53 [2] usb usb4: configuration #1 chosen from 1 choice
Oct 5 01:34:53 [2] hub 4-0:1.0: USB hub found
Oct 5 01:34:53 [2] hub 4-0:1.0: 2 ports detected
Oct 5 01:34:53 [2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Oct 5 01:34:53 [4] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
Oct 5 01:34:53 [1] ehci_hcd 0000:00:1d.7: setting latency timer to 64
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: EHCI Host Controller
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: debug port 1
Oct 5 01:34:53 [1] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa7fc00
Oct 5 01:34:53 [2] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
Oct 5 01:34:53 [2] usb usb5: configuration #1 chosen from 1 choice
Oct 5 01:34:53 [2] hub 5-0:1.0: USB hub found
Oct 5 01:34:53 [2] hub 5-0:1.0: 8 ports detected
Oct 5 01:34:53 [3] SCSI subsystem initialized
Oct 5 01:34:53 [1] libata version 3.00 loaded.
Oct 5 01:34:53 [2] sata_mv 0000:01:00.0: version 1.28
Oct 5 01:34:53 [2] sata_mv 0000:01:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
Oct 5 01:34:53 [2] sata_mv 0000:01:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
Oct 5 01:34:53 [2] scsi0 : sata_mv
Oct 5 01:34:53 [2] scsi1 : sata_mv
Oct 5 01:34:53 [2] scsi2 : sata_mv
Oct 5 01:34:53 [2] scsi3 : sata_mv
Oct 5 01:34:53 [2] ata1: SATA max UDMA/133 mmio m1048576@0xff800000 port 0xff822000 irq 21
Oct 5 01:34:53 [2] ata2: SATA max UDMA/133 mmio m1048576@0xff800000 port 0xff824000 irq 21
Oct 5 01:34:53 [2] ata3: SATA max UDMA/133 mmio m1048576@0xff800000 port 0xff826000 irq 21
Oct 5 01:34:53 [2] ata4: SATA max UDMA/133 mmio m1048576@0xff800000 port 0xff828000 irq 21
Oct 5 01:34:53 [2] sata_mv 0000:01:01.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
Oct 5 01:34:53 [2] sata_mv 0000:01:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
Oct 5 01:34:53 [2] scsi4 : sata_mv
Oct 5 01:34:53 [2] scsi5 : sata_mv
Oct 5 01:34:53 [2] scsi6 : sata_mv
Oct 5 01:34:53 [2] scsi7 : sata_mv
Oct 5 01:34:53 [2] ata5: SATA max UDMA/133 mmio m1048576@0xff600000 port 0xff622000 irq 22
Oct 5 01:34:53 [2] ata6: SATA max UDMA/133 mmio m1048576@0xff600000 port 0xff624000 irq 22
Oct 5 01:34:53 [2] ata7: SATA max UDMA/133 mmio m1048576@0xff600000 port 0xff626000 irq 22
Oct 5 01:34:53 [2] ata8: SATA max UDMA/133 mmio m1048576@0xff600000 port 0xff628000 irq 22
Oct 5 01:34:53 [2] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Oct 5 01:34:53 [2] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:53 [2] ata1.00: ATA-6: ST3160827AS, 3.42, max UDMA/133
Oct 5 01:34:53 [2] ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:53 [2] ata5.00: ATA-8: WDC WD10EARS-00MVWB0, 50.0AB50, max UDMA/133
Oct 5 01:34:53 [2] ata5.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:53 [2] ata1.00: configured for UDMA/133
Oct 5 01:34:53 [3] scsi 0:0:0:0: Direct-Access ATA ST3160827AS 3.42 PQ: 0 ANSI: 5
Oct 5 01:34:53 [2] ata5.00: configured for UDMA/133
Oct 5 01:34:54 [2] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:54 [2] ata2.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Oct 5 01:34:54 [2] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:54 [2] ata2.00: configured for UDMA/133
Oct 5 01:34:54 [3] scsi 1:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Oct 5 01:34:54 [2] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:54 [2] ata3.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Oct 5 01:34:54 [2] ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:54 [2] ata3.00: configured for UDMA/133
Oct 5 01:34:54 [3] scsi 2:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Oct 5 01:34:55 [2] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:55 [2] ata4.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Oct 5 01:34:55 [2] ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:55 [2] ata4.00: configured for UDMA/133
Oct 5 01:34:55 [3] scsi 3:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Oct 5 01:34:55 [3] scsi 4:0:0:0: Direct-Access ATA WDC WD10EARS-00M 50.0 PQ: 0 ANSI: 5
Oct 5 01:34:55 [2] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:55 [2] ata6.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Oct 5 01:34:55 [2] ata6.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:55 [2] ata6.00: configured for UDMA/133
Oct 5 01:34:55 [3] scsi 5:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Oct 5 01:34:56 [2] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Oct 5 01:34:56 [2] ata7.00: ATA-8: WDC WD20EARS-00MVWB0, 50.0AB50, max UDMA/133
Oct 5 01:34:56 [2] ata7.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Oct 5 01:34:56 [2] ata7.00: configured for UDMA/133
Oct 5 01:34:56 [3] scsi 6:0:0:0: Direct-Access ATA WDC WD20EARS-00M 50.0 PQ: 0 ANSI: 5
Oct 5 01:34:56 [2] ata8: SATA link down (SStatus 0 SControl 300)
Oct 5 01:34:56 [2] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
Oct 5 01:34:56 [2] e100: Copyright(c) 1999-2006 Intel Corporation
Oct 5 01:34:56 [2] e100 0000:01:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
Oct 5 01:34:56 [2] e100 0000:01:08.0: PME# disabled
Oct 5 01:34:56 [2] e100: eth0: e100_probe: addr 0xff4ff000, irq 20, MAC addr 00:0c:f1:e0:83:4c
Oct 5 01:34:56 [2] Uniform Multi-Platform E-IDE driver
Oct 5 01:34:56 [2] piix 0000:00:1f.1: IDE controller (0x8086:0x24db rev 0x02)
Oct 5 01:34:56 [2] PIIX_IDE 0000:00:1f.1: enabling device (0005 -> 0007)
Oct 5 01:34:56 [2] PIIX_IDE 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Oct 5 01:34:56 [2] piix 0000:00:1f.1: not 100% native mode: will probe irqs later
Oct 5 01:34:56 [2] ide0: BM-DMA at 0xffa0-0xffa7
Oct 5 01:34:56 [2] ide1: BM-DMA at 0xffa8-0xffaf
Oct 5 01:34:56 [1] Probing IDE interface ide0.
Oct 5 01:34:57 [2] hda: Optiarc DVD RW AD-7200A, ATAPI CD/DVD-ROM drive
Oct 5 01:34:58 [1] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
Oct 5 01:34:58 [4] hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
Oct 5 01:34:58 [2] hda: UDMA/33 mode selected
Oct 5 01:34:58 [1] Probing IDE interface ide1.
Oct 5 01:34:58 [2] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Oct 5 01:34:58 [2] ide1 at 0x170-0x177,0x376 on irq 15
Oct 5 01:34:58 [1] ata_piix 0000:00:1f.2: version 2.13
Oct 5 01:34:58 [2] ata_piix 0000:00:1f.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Oct 5 01:34:58 [2] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
Oct 5 01:34:58 [1] ata_piix 0000:00:1f.2: setting latency timer to 64
Oct 5 01:34:58 [2] scsi8 : ata_piix
Oct 5 01:34:58 [2] scsi9 : ata_piix
Oct 5 01:34:58 [2] ata9: SATA max UDMA/133 cmd 0xe800 ctl 0xe400 bmdma 0xd800 irq 18
Oct 5 01:34:58 [2] ata10: SATA max UDMA/133 cmd 0xe000 ctl 0xdc00 bmdma 0xd808 irq 18
Oct 5 01:34:58 [2] ata9.00: ATA-8: WDC WD10EADS-00P8B0, 01.00A01, max UDMA/133
Oct 5 01:34:58 [2] ata9.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
Oct 5 01:34:58 [2] ata9.00: configured for UDMA/133
Oct 5 01:34:58 [3] scsi 8:0:0:0: Direct-Access ATA WDC WD10EADS-00P 01.0 PQ: 0 ANSI: 5
Oct 5 01:34:59 [2] ata10.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Oct 5 01:34:59 [2] ata10.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
Oct 5 01:34:59 [2] ata10.00: configured for UDMA/133
Oct 5 01:34:59 [3] scsi 9:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Oct 5 01:35:00 [4] Driver 'sd' needs updating - please use bus_type methods
Oct 5 01:35:00 [3] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
Oct 5 01:35:00 [3] sd 0:0:0:0: [sda] Write Protect is off
Oct 5 01:35:00 [1] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sda:<5>sd 1:0:0:0: [sdb] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 1:0:0:0: [sdb] Write Protect is off
Oct 5 01:35:00 [1] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdb:<5>sd 2:0:0:0: [sdc] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 2:0:0:0: [sdc] Write Protect is off
Oct 5 01:35:00 [1] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdc:<5>sd 3:0:0:0: [sdd] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 3:0:0:0: [sdd] Write Protect is off
Oct 5 01:35:00 [1] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdd:
Oct 5 01:35:00 [3] sd 4:0:0:0: [sde] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
Oct 5 01:35:00 [3] sd 4:0:0:0: [sde] Write Protect is off
Oct 5 01:35:00 [1] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sde:<5>sd 5:0:0:0: [sdf] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 5:0:0:0: [sdf] Write Protect is off
Oct 5 01:35:00 [1] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdf:<5>sd 6:0:0:0: [sdg] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 6:0:0:0: [sdg] Write Protect is off
Oct 5 01:35:00 [1] sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdg:<5>sd 8:0:0:0: [sdh] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
Oct 5 01:35:00 [3] sd 8:0:0:0: [sdh] Write Protect is off
Oct 5 01:35:00 [1] sd 8:0:0:0: [sdh] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 8:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdh:<5>sd 9:0:0:0: [sdi] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB)
Oct 5 01:35:00 [3] sd 9:0:0:0: [sdi] Write Protect is off
Oct 5 01:35:00 [1] sd 9:0:0:0: [sdi] Mode Sense: 00 3a 00 00
Oct 5 01:35:00 [3] sd 9:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 5 01:35:00 [2] sdi:
Oct 5 01:35:00 [2] sda1
Oct 5 01:35:00 [3] sd 0:0:0:0: [sda] Attached SCSI disk
Oct 5 01:35:00 [4] sdb1
Oct 5 01:35:00 [4] sde1
Oct 5 01:35:00 [4] sdc1
Oct 5 01:35:00 [4] sdf1
Oct 5 01:35:00 [3] sd 1:0:0:0: [sdb] Attached SCSI disk
Oct 5 01:35:00 [3] sd 4:0:0:0: [sde] Attached SCSI disk
Oct 5 01:35:00 [3] sd 2:0:0:0: [sdc] Attached SCSI disk
Oct 5 01:35:00 [3] sd 5:0:0:0: [sdf] Attached SCSI disk
Oct 5 01:35:00 [4] sdd1
Oct 5 01:35:00 [3] sd 3:0:0:0: [sdd] Attached SCSI disk
Oct 5 01:35:00 [4] sdg1
Oct 5 01:35:00 [3] sd 6:0:0:0: [sdg] Attached SCSI disk
Oct 5 01:35:00 [4] sdi1
Oct 5 01:35:00 [4] sdh1
Oct 5 01:35:00 [3] sd 9:0:0:0: [sdi] Attached SCSI disk
Oct 5 01:35:00 [3] sd 8:0:0:0: [sdh] Attached SCSI disk
Oct 5 01:35:00 [2] ide-cd driver 5.00
Oct 5 01:35:00 [2] ide-cd: hda: ATAPI 48X DVD-ROM DVD-R/RAM CD-R/RW drive, 2048kB Cache
Oct 5 01:35:00 [2] Uniform CD-ROM driver Revision: 3.20
Oct 5 01:35:56 [2] e100: eth0 NIC Link is Up 100 Mbps Full Duplex
Oct 5 01:43:48 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:48 [2] EXT3 FS on sdb1, internal journal
Oct 5 01:43:48 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:49 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:49 [2] EXT3 FS on sdc1, internal journal
Oct 5 01:43:49 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:49 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:49 [2] EXT3 FS on sdd1, internal journal
Oct 5 01:43:49 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:49 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:49 [2] EXT3 FS on sde1, internal journal
Oct 5 01:43:49 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:50 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:50 [2] EXT3 FS on sdf1, internal journal
Oct 5 01:43:50 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:51 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:51 [2] EXT3 FS on sdg1, internal journal
Oct 5 01:43:51 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:51 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:51 [2] EXT3 FS on sdh1, internal journal
Oct 5 01:43:51 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:43:51 [2] kjournald starting. Commit interval 5 seconds
Oct 5 01:43:51 [2] EXT3 FS on sdi1, internal journal
Oct 5 01:43:51 [2] EXT3-fs: mounted filesystem with writeback data mode.
Oct 5 01:44:24 [2] Adding 999416k swap on /export/Disk-4/_NL_SWAP/VRAM. Priority:-1 extents:254 across:1017068k
Oct 5 02:26:15 [2] warning: `smbd' uses 32-bit capabilities (legacy support in use)

Mark

If you Google for KLOGD I think you will find a lot of info out there about it but you will have to do some reading to get what you need.

Doug