NASLite Network Attached Storage

So, I've upgraded to NasLite M2 V1.01. The hardware is the same since version 2.6 but now something strange happens.

It seems, I've not tested it fully, apologies, then when I insert the NTP ip address and I save the config, after the reboot the server loose it naslite config and start as has just been installed.
To add strange to strange, yesterday, after having input the NTP IP addr, it worked after the first reboot. I shut down the server for the night and this morning it started vanilla.
Configured everything back, unlocked the license, added the NTP ip addr, after the reboot is vanilla again.

The server boots up from a Compact Flash into a USB reader from a brand new Sandisk Extreme 1GB.

The NTP server I'm using is one of these:
* ntp1.inrim.it (193.204.114.232)
* ntp2.inrim.it (193.204.114.233)

Has this happened to anybody else?

I will not have access to this machine for the next three days, so I'm attaching the syslog as well, it may be useful:

System Message Log:

* Feb 10 08:53:19 [3] klogd started: BusyBox v1.01 (2008.07.26-02:54+0000)
* Feb 10 08:53:19 [2] cache: 16K
* Feb 10 08:53:19 [2] CPU: L2 cache: 1024K
* Feb 10 08:53:19 [2] Intel machine check architecture supported.
* Feb 10 08:53:19 [2] Intel machine check reporting enabled on CPU#0.
* Feb 10 08:53:19 [1] CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
* Feb 10 08:53:19 [1] CPU: Common caps: bfebfbff 00000000 00000000 00000000
* Feb 10 08:53:19 [4] CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 04
* Feb 10 08:53:19 [2] Enabling fast FPU save and restore. done.
* Feb 10 08:53:19 [2] Enabling unmasked SIMD FPU exception support. done.
* Feb 10 08:53:19 [2] Checking 'hlt' instruction. OK.
* Feb 10 08:53:19 [4] POSIX conformance testing by UNIFIX
* Feb 10 08:53:19 [4] enabled ExtINT on CPU#0
* Feb 10 08:53:19 [4] ESR value before enabling vector: 00000000
* Feb 10 08:53:19 [4] ESR value after enabling vector: 00000000
* Feb 10 08:53:19 [4] ENABLING IO-APIC IRQs
* Feb 10 08:53:19 [1] init IO_APIC IRQs
* Feb 10 08:53:19 [1] IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23, 3-0, 3-1, 3-2, 3-3, 3-4, 3-5, 3-6, 3-7, 3-8, 3-9, 3-10, 3-11, 3-12, 3-13, 3-14, 3-15, 3-16, 3-17, 3-18, 3-19, 3-20, 3-21, 3-22, 3-23 not connected.
* Feb 10 08:53:19 [2] TIMER: vector=0x31 pin1=2 pin2=-1
* Feb 10 08:53:19 [4] Using local APIC timer interrupts.
* Feb 10 08:53:19 [4] calibrating APIC timer .
* Feb 10 08:53:19 [4] . CPU clock speed is 3351.6050 MHz.
* Feb 10 08:53:19 [4] . host bus clock speed is 239.4003 MHz.
* Feb 10 08:53:19 [4] cpu: 0, clocks: 2394003, slice: 1197001
* Feb 10 08:53:19 [4] CPU0
* Feb 10 08:53:19 [4] mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
* Feb 10 08:53:19 [4] mtrr: detected mtrr type: Intel
* Feb 10 08:53:19 [2] ACPI: Subsystem revision 20040326
* Feb 10 08:53:19 [2] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
* Feb 10 08:53:19 [2] PCI: Using configuration type 1
* Feb 10 08:53:19 [2] ACPI: Interpreter enabled
* Feb 10 08:53:19 [2] ACPI: Using IOAPIC for interrupt routing
* Feb 10 08:53:19 [2] ACPI: System [ACPI] (supports S0 S1 S4 S5)
* Feb 10 08:53:19 [2] ACPI: PCI Root Bridge [PCI0] (00:00)
* Feb 10 08:53:19 [4] PCI: Probing PCI hardware (bus 00)
* Feb 10 08:53:19 [2] PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
* Feb 10 08:53:19 [4] Transparent bridge - PCI device 8086:244e
* Feb 10 08:53:19 [1] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
* Feb 10 08:53:19 [1] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
* Feb 10 08:53:19 [1] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
* Feb 10 08:53:19 [4] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 9 11 12 14 15)
* Feb 10 08:53:19 [4] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 9 11 12 14 15)
* Feb 10 08:53:19 [4] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 9 11 12 14 15)
* Feb 10 08:53:19 [4] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *9 11 12 14 15)
* Feb 10 08:53:19 [4] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 9 11 12 14 15) *0, disabled.
* Feb 10 08:53:19 [4] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 9 *11 12 14 15)
* Feb 10 08:53:19 [4] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 9 11 12 14 15) *0, disabled.
* Feb 10 08:53:19 [4] ACPI: PCI Interrupt Link [LNKH] (IRQs *7)
* Feb 10 08:53:19 [2] PCI: Probing PCI hardware
* Feb 10 08:53:19 [1] 00:00:01[A] -> 2-16 -> IRQ 16 level low
* Feb 10 08:53:19 [1] 00:00:01[B] -> 2-17 -> IRQ 17 level low
* Feb 10 08:53:19 [1] 00:00:03[B] -> 2-18 -> IRQ 18 level low
* Feb 10 08:53:19 [1] 00:00:1d[B] -> 2-19 -> IRQ 19 level low
* Feb 10 08:53:19 [1] 00:00:1d[D] -> 2-23 -> IRQ 23 level low
* Feb 10 08:53:19 [1] 00:02:00[A] -> 2-21 -> IRQ 21 level low
* Feb 10 08:53:19 [1] 00:01:02[A] -> 3-0 -> IRQ 24 level low
* Feb 10 08:53:19 [1] 00:01:02[B] -> 3-1 -> IRQ 25 level low
* Feb 10 08:53:19 [1] 00:01:02[C] -> 3-2 -> IRQ 26 level low
* Feb 10 08:53:19 [1] 00:01:02[D] -> 3-3 -> IRQ 27 level low
* Feb 10 08:53:19 [1] number of MP IRQ sources: 15.
* Feb 10 08:53:19 [1] number of IO-APIC #2 registers: 24.
* Feb 10 08:53:19 [1] number of IO-APIC #3 registers: 24.
* Feb 10 08:53:19 [2] testing the IO APIC.
* Feb 10 08:53:19 [4]
* Feb 10 08:53:19 [1] IO APIC #2
* Feb 10 08:53:19 [1] register #00: 02000000
* Feb 10 08:53:19 [1] . : physical APIC id: 02
* Feb 10 08:53:19 [1] . : Delivery Type: 0
* Feb 10 08:53:19 [1] . : LTS : 0
* Feb 10 08:53:19 [1] register #01: 00178020
* Feb 10 08:53:19 [1] . : max redirection entries: 0017
* Feb 10 08:53:19 [1] . : PRQ implemented: 1
* Feb 10 08:53:19 [1] . : IO APIC version: 0020
* Feb 10 08:53:19 [1] register #03: 00000001
* Feb 10 08:53:19 [1] . : Boot DT : 1
* Feb 10 08:53:19 [1] IRQ redirection table:
* Feb 10 08:53:19 [1] NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
* Feb 10 08:53:19 [1] 00 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 01 001 01 0 0 0 0 0 1 1 39
* Feb 10 08:53:19 [1] 02 001 01 0 0 0 0 0 1 1 31
* Feb 10 08:53:19 [1] 03 001 01 0 0 0 0 0 1 1 41
* Feb 10 08:53:19 [1] 04 001 01 0 0 0 0 0 1 1 49
* Feb 10 08:53:19 [1] 05 001 01 0 0 0 0 0 1 1 51
* Feb 10 08:53:19 [1] 06 001 01 0 0 0 0 0 1 1 59
* Feb 10 08:53:19 [1] 07 001 01 0 0 0 0 0 1 1 61
* Feb 10 08:53:19 [1] 08 001 01 0 0 0 0 0 1 1 69
* Feb 10 08:53:19 [1] 09 001 01 0 0 0 0 0 1 1 71
* Feb 10 08:53:19 [1] 0a 001 01 0 1 0 0 0 1 1 79
* Feb 10 08:53:19 [1] 81
* Feb 10 08:53:19 [1] 0c 001 01 0 0 0 0 0 1 1 89
* Feb 10 08:53:19 [1] 0d 001 01 0 0 0 0 0 1 1 91
* Feb 10 08:53:19 [1] 0e 001 01 0 0 0 0 0 1 1 99
* Feb 10 08:53:19 [1] 0f 001 01 0 0 0 0 0 1 1 A1
* Feb 10 08:53:19 [1] 10 001 01 1 1 0 1 0 1 1 A9
* Feb 10 08:53:19 [1] 11 001 01 1 1 0 1 0 1 1 B1
* Feb 10 08:53:19 [1] 12 001 01 1 1 0 1 0 1 1 B9
* Feb 10 08:53:19 [1] 13 001 01 1 1 0 1 0 1 1 C1
* Feb 10 08:53:19 [1] 14 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 15 001 01 1 1 0 1 0 1 1 D1
* Feb 10 08:53:19 [1] 16 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 17 001 01 1 1 0 1 0 1 1 C9
* Feb 10 08:53:19 [4]
* Feb 10 08:53:19 [1] IO APIC #3
* Feb 10 08:53:19 [1] register #00: 03000000
* Feb 10 08:53:19 [1] . : physical APIC id: 03
* Feb 10 08:53:19 [1] . : Delivery Type: 0
* Feb 10 08:53:19 [1] . : LTS : 0
* Feb 10 08:53:19 [1] register #01: 00178020
* Feb 10 08:53:19 [1] . : max redirection entries: 0017
* Feb 10 08:53:19 [1] . : PRQ implemented: 1
* Feb 10 08:53:19 [1] . : IO APIC version: 0020
* Feb 10 08:53:19 [1] register #03: 00000001
* Feb 10 08:53:19 [1] . : Boot DT : 1
* Feb 10 08:53:19 [1] IRQ redirection table:
* Feb 10 08:53:19 [1] NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
* Feb 10 08:53:19 [1] 00 001 01 1 1 0 1 0 1 1 D9
* Feb 10 08:53:19 [1] 01 001 01 1 1 0 1 0 1 1 E1
* Feb 10 08:53:19 [1] 02 001 01 1 1 0 1 0 1 1 E9
* Feb 10 08:53:19 [1] 03 001 01 1 1 0 1 0 1 1 32
* Feb 10 08:53:19 [1] 04 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 05 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 06 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 07 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 08 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 09 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 0a 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 0b 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 0c 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 0d 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 0e 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 0f 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 10 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 11 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 12 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 13 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 14 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 15 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 16 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] 17 000 00 1 0 0 0 0 0 0 00
* Feb 10 08:53:19 [1] IRQ to pin mappings:
* Feb 10 08:53:19 [1] IRQ0 -> 0:2
* Feb 10 08:53:19 [1] IRQ1 -> 0:1
* Feb 10 08:53:19 [1] IRQ3 -> 0:3
* Feb 10 08:53:19 [1] IRQ4 -> 0:4
* Feb 10 08:53:19 [1] IRQ5 -> 0:5
* Feb 10 08:53:19 [1] IRQ6 -> 0:6
* Feb 10 08:53:19 [1] IRQ7 -> 0:7
* Feb 10 08:53:19 [1] IRQ8 -> 0:8
* Feb 10 08:53:19 [1] IRQ9 -> 0:9
* Feb 10 08:53:19 [1] IRQ10 -> 0:10
* Feb 10 08:53:19 [1] IRQ11 -> 0:11
* Feb 10 08:53:19 [1] IRQ12 -> 0:12
* Feb 10 08:53:19 [1] IRQ13 -> 0:13
* Feb 10 08:53:19 [1] IRQ14 -> 0:14
* Feb 10 08:53:19 [1] IRQ15 -> 0:15
* Feb 10 08:53:19 [1] IRQ16 -> 0:16
* Feb 10 08:53:19 [1] IRQ17 -> 0:17
* Feb 10 08:53:19 [1] IRQ18 -> 0:18
* Feb 10 08:53:19 [1] IRQ19 -> 0:19
* Feb 10 08:53:19 [1] IRQ21 -> 0:21
* Feb 10 08:53:19 [1] IRQ23 -> 0:23
* Feb 10 08:53:19 [1] IRQ24 -> 1:0
* Feb 10 08:53:19 [1] IRQ25 -> 1:1
* Feb 10 08:53:19 [1] IRQ26 -> 1:2
* Feb 10 08:53:19 [1] IRQ27 -> 1:3
* Feb 10 08:53:19 [2] done.
* Feb 10 08:53:19 [2] PCI: Using ACPI for IRQ routing
* Feb 10 08:53:19 [2] Linux NET4.0 for Linux 2.4
* Feb 10 08:53:19 [2] Based upon Swansea University Computer Society NET3.039
* Feb 10 08:53:19 [4] Initializing RT netlink socket
* Feb 10 08:53:19 [4] Starting kswapd
* Feb 10 08:53:19 [4] allocated 32 pages and 32 bhs reserved for the highmem bounces
* Feb 10 08:53:19 [2] Journalled Block Device driver loaded
* Feb 10 08:53:19 [2] devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
* Feb 10 08:53:19 [2] devfs: boot_options: 0x1
* Feb 10 08:53:19 [2] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
* Feb 10 08:53:19 [2] ACPI: Power Button (FF) [PWRF]
* Feb 10 08:53:19 [2] ACPI: Sleep Button (CM) [SLPB]
* Feb 10 08:53:19 [2] ACPI: Processor [CPU1] (supports C1, 8 throttling states)
* Feb 10 08:53:19 [2] ACPI: Processor [CPU2] (supports C1)
* Feb 10 08:53:19 [4] pty: 256 Unix98 ptys configured
* Feb 10 08:53:19 [2] Real Time Clock Driver v1.10f
* Feb 10 08:53:19 [2] Floppy drive(s): fd0 is 1.44M
* Feb 10 08:53:19 [2] FDC 0 is a post-1991 82077
* Feb 10 08:53:19 [4] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
* Feb 10 08:53:19 [2] loop: loaded (max 8 devices)
* Feb 10 08:53:19 [2] Intel(R) PRO/1000 Network Driver - version 7.3.20-k4
* Feb 10 08:53:19 [2] Copyright (c) 1999-2006 Intel Corporation.
* Feb 10 08:53:19 [2] e1000: 02:02.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:cf:03:e1
* Feb 10 08:53:19 [2] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
* Feb 10 08:53:19 [2] dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15
* Feb 10 08:53:19 [4] FW Version=$Version$
* Feb 10 08:53:19 [2] pcnet32.c:v1.30h 06.24.2004 tsbogend@alpha.franken.de
* Feb 10 08:53:19 [2] ThunderLAN driver v1.15
* Feb 10 08:53:19 [2] SA: 0
* Feb 10 08:53:19 [2] dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
* Feb 10 08:53:19 [2] ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
* Feb 10 08:53:19 [4] sk98lin: No adapter found.
* Feb 10 08:53:19 [2] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.50.
* Feb 10 08:53:19 [2] Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
* Feb 10 08:53:19 [2] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
* Feb 10 08:53:19 [2] ICH5: IDE controller at PCI slot 00:1f.1
* Feb 10 08:53:19 [2] ICH5: chipset revision 2
* Feb 10 08:53:19 [2] ICH5: not 100% native mode: will probe irqs later
* Feb 10 08:53:19 [2] ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
* Feb 10 08:53:19 [2] ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
* Feb 10 08:53:19 [4] hdc: HL-DT-ST DVDRAM GSA-H42N, ATAPI CD/DVD-ROM drive
* Feb 10 08:53:19 [4] ide1 at 0x170-0x177,0x376 on irq 15
* Feb 10 08:53:19 [4] hdc: attached ide-cdrom driver.
* Feb 10 08:53:19 [2] hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
* Feb 10 08:53:19 [2] Uniform CD-ROM driver Revision: 3.12
* Feb 10 08:53:19 [2] SCSI subsystem driver Revision: 1.00
* Feb 10 08:53:19 [2] Loading Adaptec I2O RAID: Version 2.4 Build 5
* Feb 10 08:53:19 [2] Detecting Adaptec I2O RAID controllers.
* Feb 10 08:53:19 [2] Red Hat/Adaptec aacraid driver (1.1-3 Jan 12 2009 23:06:00)
* Feb 10 08:53:19 [4] scsi: Detection failed (no card)
* Feb 10 08:53:19 [3] megaraid: v2.10.10.1 (Release Date: Thu Jan 27 16:19:44 EDT 2005)
* Feb 10 08:53:19 [3] megaraid: found 0x1000:0x1960:bus 1:slot 3:func 0
* Feb 10 08:53:19 [3] scsi1:Found MegaRAID controller at 0xf882c000, IRQ:25
* Feb 10 08:53:19 [3] megaraid: [713S:G121] detected 1 logical drives.
* Feb 10 08:53:19 [3] megaraid: supports extended CDBs.
* Feb 10 08:53:19 [2] megaraid: channel[0] is raid.
* Feb 10 08:53:19 [3] megaraid: no BIOS enabled.
* Feb 10 08:53:19 [2] scsi1 : LSI Logic MegaRAID 713S 254 commands 16 targs 4 chans 7 luns
* Feb 10 08:53:19 [3] scsi1: scanning scsi channel 0 for logical drives.
* Feb 10 08:53:19 [4] Vendor: MegaRAID Model: LD 0 RAID1 1907G Rev: 713S
* Feb 10 08:53:19 [4] Type: Direct-Access ANSI SCSI revision: 02
* Feb 10 08:53:19 [3] scsi1: scanning scsi channel 1 for logical drives.
* Feb 10 08:53:19 [3] scsi1: scanning scsi channel 2 for logical drives.
* Feb 10 08:53:19 [3] scsi1: scanning scsi channel 3 for logical drives.
* Feb 10 08:53:19 [3] scsi1: scanning scsi channel 4 [P0] for physical devices.
* Feb 10 08:53:19 [4] GDT-HA: Storage RAID Controller Driver. Version: 3.04
* Feb 10 08:53:19 [4] GDT-HA: Found 0 PCI Storage RAID Controllers
* Feb 10 08:53:19 [2] scsi2 : SCSI host adapter emulation for IDE ATAPI devices
* Feb 10 08:53:19 [4] 3ware Storage Controller device driver for Linux v1.02.00.037.
* Feb 10 08:53:19 [4] 3w-xxxx: No cards found.
* Feb 10 08:53:19 [1] libata version 1.20 loaded.
* Feb 10 08:53:19 [1] PCI(00:1f.2): version 1.05
* Feb 10 08:53:19 [1] PCI: Setting latency timer of device 00:1f.2 to 64
* Feb 10 08:53:19 [2] ata1: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xD400 irq 18
* Feb 10 08:53:19 [2] ata2: SATA max UDMA/133 cmd 0xDC00 ctl 0xD802 bmdma 0xD408 irq 18
* Feb 10 08:53:19 [1] ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:207f
* Feb 10 08:53:19 [2] ata1: dev 0 ATA-7, max UDMA/133, 625142448 sectors: LBA48
* Feb 10 08:53:19 [2] ata1: dev 0 configured for UDMA/133
* Feb 10 08:53:19 [1] ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:207f
* Feb 10 08:53:19 [2] ata2: dev 0 ATA-7, max UDMA/133, 625142448 sectors: LBA48
* Feb 10 08:53:19 [2] ata2: dev 0 configured for UDMA/133
* Feb 10 08:53:19 [2] scsi3 : ata_piix
* Feb 10 08:53:19 [2] scsi4 : ata_piix
* Feb 10 08:53:19 [4] Vendor: ATA Model: MAXTOR STM332082 Rev: 3.AA
* Feb 10 08:53:19 [4] Type: Direct-Access ANSI SCSI revision: 05
* Feb 10 08:53:19 [4] Vendor: ATA Model: MAXTOR STM332082 Rev: 3.AA
* Feb 10 08:53:19 [4] Type: Direct-Access ANSI SCSI revision: 05
* Feb 10 08:53:19 [4] Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
* Feb 10 08:53:19 [4] Attached scsi disk sdb at scsi3, channel 0, id 0, lun 0
* Feb 10 08:53:19 [4] Attached scsi disk sdc at scsi4, channel 0, id 0, lun 0
* Feb 10 08:53:19 [4] SCSI device sda: 3907031040 512-byte hdwr sectors (2000400 MB)
* Feb 10 08:53:19 [2] Partition check:
* Feb 10 08:53:19 [2] /dev/scsi/host1/bus0/target0/lun0: p1
* Feb 10 08:53:19 [4] SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
* Feb 10 08:53:19 [2] /dev/scsi/host3/bus0/target0/lun0: p1
* Feb 10 08:53:19 [4] SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
* Feb 10 08:53:19 [2] /dev/scsi/host4/bus0/target0/lun0: p1
* Feb 10 08:53:19 [2] raw1394: /dev/raw1394 device initialized
* Feb 10 08:53:19 [2] sbp2: $Rev: 1074 $ Ben Collins
* Feb 10 08:53:19 [5] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
* Feb 10 08:53:19 [2] usb.c: registered new driver usbdevfs
* Feb 10 08:53:19 [2] usb.c: registered new driver hub
* Feb 10 08:53:19 [1] PCI: Setting latency timer of device 00:1d.7 to 64
* Feb 10 08:53:19 [2] ehci_hcd 00:1d.7: PCI device 8086:25ad
* Feb 10 08:53:19 [2] ehci_hcd 00:1d.7: irq 23, pci mem f8830c00
* Feb 10 08:53:19 [2] usb.c: new USB bus registered, assigned bus number 1
* Feb 10 08:53:19 [2] led 64bit PCI DMA
* Feb 10 08:53:19 [1] PCI: cache line size of 128 is not supported by device 00:1d.7
* Feb 10 08:53:19 [2] ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
* Feb 10 08:53:19 [2] hub.c: USB hub found
* Feb 10 08:53:19 [2] hub.c: 4 ports detected
* Feb 10 08:53:19 [2] host/uhci.c: USB Universal Host Controller Interface driver v1.1
* Feb 10 08:53:19 [1] PCI: Setting latency timer of device 00:1d.0 to 64
* Feb 10 08:53:19 [2] host/uhci.c: USB UHCI at I/O 0xe800, IRQ 16
* Feb 10 08:53:19 [2] usb.c: new USB bus registered, assigned bus number 2
* Feb 10 08:53:19 [2] hub.c: USB hub found
* Feb 10 08:53:19 [2] hub.c: 2 ports detected
* Feb 10 08:53:19 [1] PCI: Setting latency timer of device 00:1d.1 to 64
* Feb 10 08:53:19 [2] host/uhci.c: USB UHCI at I/O 0xec00, IRQ 19
* Feb 10 08:53:19 [2] usb.c: new USB bus registered, assigned bus number 3
* Feb 10 08:53:19 [2] hub.c: USB hub found
* Feb 10 08:53:19 [2] hub.c: 2 ports detected
* Feb 10 08:53:19 [2] usb.c: registered new driver usbkbd
* Feb 10 08:53:19 [2] usbkbd.c: :USB HID Boot Protocol keyboard driver
* Feb 10 08:53:19 [2] Initializing USB Mass Storage driver.
* Feb 10 08:53:19 [2] usb.c: registered new driver usb-storage
* Feb 10 08:53:19 [2] USB Mass Storage support registered.
* Feb 10 08:53:19 [2] NET4: Linux TCP/IP 1.0 for NET4.0
* Feb 10 08:53:19 [2] IP Protocols: ICMP, UDP, TCP
* Feb 10 08:53:19 [2] IP: routing cache hash table of 16384 buckets, 128Kbytes
* Feb 10 08:53:19 [2] TCP: Hash tables configured (established 262144 bind 65536)
* Feb 10 08:53:19 [2] NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
* Feb 10 08:53:19 [3] RAMDISK: NASLite file system found at block 0
* Feb 10 08:53:19 [4] .<6>hub.c: new USB device 00:1d.7-3, assigned address 2
* Feb 10 08:53:19 [4] .<6>scsi5 : SCSI emulation for USB Mass Storage devices
* Feb 10 08:53:19 [4] Vendor: Generic Model: STORAGE DEVICE Rev: 9715
* Feb 10 08:53:19 [4] Type: Direct-Access ANSI SCSI revision: 02
* Feb 10 08:53:19 [4] Attached scsi removable disk sdd at scsi5, channel 0, id 0, lun 0
* Feb 10 08:53:19 [4] .SCSI device sdd: 2001888 512-byte hdwr sectors (1025 MB)
* Feb 10 08:53:19 [4] .sdd: Write Protect is off
* Feb 10 08:53:19 [2] /dev/scsi/host5/bus0/target0/lun0: p1 p2
* Feb 10 08:53:19 [1] WARNING: USB Mass Storage data integrity not assured
* Feb 10 08:53:19 [1] USB Mass Storage device found at 2
* Feb 10 08:53:19 [4] .<6>Freeing initrd memory: 4137k freed
* Feb 10 08:53:19 [4] VFS: Mounted root (ext2 filesystem).
* Feb 10 08:53:19 [2] Mounted devfs on /dev
* Feb 10 08:53:19 [2] Freeing unused kernel memory: 560k freed
* Feb 10 08:53:19 [2] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
* Feb 10 08:53:19 [2] kjournald starting. Commit interval 5 seconds
* Feb 10 08:53:19 [2] EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
* Feb 10 08:53:19 [2] EXT3-fs: mounted filesystem with ordered data mode.
* Feb 10 08:53:19 [2] kjournald starting. Commit interval 5 seconds
* Feb 10 08:53:19 [2] EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,17), internal journal
* Feb 10 08:53:19 [2] EXT3-fs: mounted filesystem with ordered data mode.
* Feb 10 08:53:19 [2] kjournald starting. Commit interval 5 seconds
* Feb 10 08:53:19 [2] EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,33), internal journal
* Feb 10 08:53:19 [2] EXT3-fs: mounted filesystem with ordered data mode.
* Feb 10 08:53:19 [2] Adding Swap: 1048568k swap-space (priority -1)

Be sure and save your config after making changes, you also need to reboot for them to take effect. Just because you put in the IP address does not mean it will stick, you have to save the configuration after you make any changes. Again be sure to reboot as well.

Mike

Mike, I thank you for the advice but is actually not helping.

You are probably aware that to unlock the product you need to configure the network, save and reboot, and then access via Web to get the unlock code, save and reboot again, to enable the license.

In my previous message i stated that the config gets back to vanilla, as the product was just installed so, as you can see, at least a couple of configurations saves and reboots have been done.

So, thank you very much and I want to make you sure I've saved the config and rebooted the machine.

Thanks

Just covering the bases here.

I might be tempted to get rid of the FC to USB converter and go with a PATA to CF plug in board like this one.

http://cgi.ebay.com/Lot-5pcs-Compact-Flash-CF-to-ATA-IDE-adapter-converter_W0QQitemZ200303160565QQcmdZViewItemQQptZPCA_Cables_Adapters?hash=item200303160565&_trksid=p3286.c0.m14&_trkparms=72%3A1205|66%3A2|65%3A12|39%3A1|240%3A1318|301%3A1|293%3A1|294%3A50

I use the exact same one my self for my HDD boot and it works perfectly with no issues.

I suspect that the config file is not being written for some reason. The CF card is basically a solid state flash drive with an ATA interface and so will work best if it is used in that way. I always had issues with the converters like you are using now because most are based on chips with really poorly implemented interface standards.

Mike

first off naslite doesn't do ntp so unless the server is rfc 868 compliant, you wont get your time adjusted. as far as your usb issue goes, some of those usb to cf adapters are actually a hub and will look differently to the bios as they do to the kernel depending on how the boot is done. that is cold boot or a reboot.

i'd dump that contraption and use something sane like ide to cf as mike pointed out.