NASLite Network Attached Storage

www.serverelements.com
Task-specific simplicity with low hardware requirements.
It is currently Sun Nov 28, 2021 8:42 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Tue Feb 14, 2006 10:25 pm 
Offline

Joined: Tue Feb 14, 2006 10:20 pm
Posts: 14
I previously had disk-1 and disk-3. I removed disk-1 for use in another system, plugged the NAS computer back up and now disk-3 doesn't show up. Any ideas?

# Feb 14 20:45:56 NAS user.info klogd: VP_IDE: VIA vt82c596b (rev 12) IDE UDMA66 controller on pci00:02.1
# Feb 14 20:45:56 NAS user.info klogd: ide1: BM-DMA at 0xfff8-0xffff, BIOS settings: hdc:DMA, hdd:pio
# Feb 14 20:45:56 NAS user.warn klogd: hdc: GENERIC 0000000, ATA DISK drive
# Feb 14 20:45:56 NAS user.warn klogd: blk: queue c02c4874, I/O limit 4095Mb (mask 0xffffffff)
# Feb 14 20:45:56 NAS user.warn klogd: ide1 at 0x170-0x177,0x376 on irq 15
# Feb 14 20:45:56 NAS user.warn klogd: river.
# Feb 14 20:45:56 NAS user.warn klogd: hdc: host protected area => 1
# Feb 14 20:45:56 NAS user.info klogd: hdc: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=158816/16/63, UDMA(66)
# Feb 14 20:45:56 NAS user.info klogd: Partition check:
# Feb 14 20:45:56 NAS user.info klogd: /dev/ide/host1/bus1/target0/lun0: p1
# Feb 14 20:45:56 NAS user.info klogd: NET4: Linux TCP/IP 1.0 for NET4.0
# Feb 14 20:45:56 NAS user.info klogd: IP Protocols: ICMP, UDP, TCP
# Feb 14 20:45:56 NAS user.info klogd: IP: routing cache hash table of 512 buckets, 4Kbytes
# Feb 14 20:45:56 NAS user.info klogd: TCP: Hash tables configured (established 8192 bind 16384)
# Feb 14 20:45:56 NAS user.info klogd: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
# Feb 14 20:45:56 NAS user.notice klogd: RAMDISK: Compressed image found at block 798
# Feb 14 20:45:56 NAS user.warn klogd: EXT2-fs warning: checktime reached, running e2fsck is recommended
# Feb 14 20:45:56 NAS user.warn klogd: VFS: Mounted root (ext2 filesystem).
# Feb 14 20:45:56 NAS user.info klogd: Mounted devfs on /dev


Top
 Profile  
 
 Post subject:
PostPosted: Tue Feb 14, 2006 11:05 pm 
Offline

Joined: Tue Feb 14, 2006 3:26 am
Posts: 7
Location: Illinois
Goldfinger,

It sounds to me like you may have a jumper issue. If drive 3 was a slave before, you will probably need to change the jumper to make it a master. This is only a guess, but could be the case. Report back and let us know what you find.

Thanks,


Top
 Profile  
 
 Post subject:
PostPosted: Thu Feb 16, 2006 4:41 pm 
Offline

Joined: Tue Feb 14, 2006 10:20 pm
Posts: 14
Odd, well for the record I got this working by hooking a CD-ROM up and running e2fsck in Knoppix.

After removing the CD-ROM drive it was gone again... I didn't know changing the number of drives would cause them all to disappear. *shrug*


Top
 Profile  
 
 Post subject:
PostPosted: Thu Feb 16, 2006 5:22 pm 
Offline
Site Admin

Joined: Tue Jul 13, 2004 4:11 pm
Posts: 1771
Location: Server Elements
Some drives have a different jumper settings for "single master" and "master with slave"


Top
 Profile  
 
 Post subject:
PostPosted: Sun Feb 19, 2006 8:02 am 
Offline

Joined: Wed Jan 04, 2006 11:27 pm
Posts: 35
Location: Melbourne, Australia
I've even seen this before with double point cables (i.e. can take 2 devices) and a single IDE device . My fix was to fork out the $8 for a new cable.

As Tony mentioned jumbers can be a big pain, so you may jsut wanan check them. If all esle fails, run ultimatebootcd and run the nessecary diag. tools.

T.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group