NASLite Network Attached Storage

www.serverelements.com
Task-specific simplicity with low hardware requirements.
It is currently Mon Dec 06, 2021 7:05 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 4 posts ] 
Author Message
 Post subject: Could be SMART-er?
PostPosted: Tue Sep 21, 2004 12:53 am 
Offline

Joined: Tue Sep 21, 2004 12:40 am
Posts: 28
Location: Tulsa, OK
OK... I just set up a NASLite server using an old IBM and some hard drives cannibalized off of various machines. Right now I only have two drives. One of them has SMART built in, and reports as healthy in the NASLite server HTML pages. The other disk reports no on-board SMART. But I'm still getting the three-high, three-low beeps that are supposed to signify a SMART failure! From the non-SMART Disk-1:

Code:
=== START OF INFORMATION SECTION ===
Device Model:     IBM-DJAA-31700                         
Serial Number:    1P05P126280
Firmware Version: P0IRA73A
ATA Version is:   1
ATA Standard is:  Unrecognized. Minor revision code: 0x00
SMART is only available in ATA Version 3 Revision 3 or greater.
We will try to proceed in spite of this.
SMART support is: Unavailable - device lacks SMART capability.
A mandatory SMART command has failed: exiting. To continue, turn on the -P option


From the SMART Disk-2:

Code:
=== START OF INFORMATION SECTION ===
Device Model:     ST32520A                               
Serial Number:    FT175250
Firmware Version: 05.05.02
ATA Version is:   4
ATA Standard is:  ATA/ATAPI-4 X3T13 1153D revision 6
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Off-line data collection status: (0x00)   Offline data collection activity was
               never started.
Total time to complete off-line
data collection:        (   0) seconds.
Offline data collection
capabilities:           (0x00)    Off-line data collection not supported.
SMART capabilities:            (0x0001)   Saves SMART data before entering
               power-saving mode.
Error logging capability:        (0x00)   Error logging NOT supported.

SMART Attributes Data Structure revision number: 5
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE     WHEN_FAILED RAW_VALUE
  5 Reallocated_Sector_Ct   0x0013   100   100   017    Pre-fail     -       511
  3 Spin_Up_Time            0x0007   100   100   060    Pre-fail     -       1744830464
  7 Seek_Error_Rate         0x000b   100   100   045    Pre-fail     -       0
  8 Seek_Time_Performance   0x0005   100   100   050    Pre-fail     -       18446744073709551615

Warning: device does not support Self Test Logging


Is there something I need to know that will cool it on the beeps? It's driving my wife bonkers. :o I'm wondering if my Disk-1 is firing off the beeps for some reason... is there a way to hack the floppy so that it doesn't beep any more for that drive? I don't need Chicken Little warning me about the sky every five minutes, but a warning if Drive-2 decides to flake out might be nice.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Sep 21, 2004 7:15 am 
Offline

Joined: Wed Sep 15, 2004 11:37 pm
Posts: 8
I had the same problem. My understanding is that the beeping cannot be disabled through the NASLite software. So, I disconnected the speaker connected to the motherboard. Actually, the speaker is integrated into the motherboard, but thankgoodness there was a speaker jumper that I removed and eliminated the beeping. This might not be the most elegant solution, but it worked. I am interested in hearing about other ways to eliminate the beeping for non-SMART hard drives.

Alan Hood


Top
 Profile  
 
 Post subject:
PostPosted: Tue Sep 21, 2004 10:05 am 
Offline

Joined: Fri Jul 16, 2004 6:25 pm
Posts: 42
Location: St. Louis
In an earlier post, Tony had promised a menu option to turn off SMART support in future versions. As of now, pulling the speaker is the only option.

Tim


Top
 Profile  
 
 Post subject:
PostPosted: Tue Mar 14, 2006 10:50 pm 
Offline

Joined: Tue Mar 14, 2006 10:30 pm
Posts: 1
I have a non-SMART capable hard drive attached and NAS-Lite doesn't beep. The only difference is, I have a SMART capable hard drive as Drive 1.

I'm assuming that if you have a SMART drive as drive 1 NAS-Lite won't beep on other drives that aren't SMART attached.

I'm using NAS-Lite FTP v1. On a P133 Dell Dimension with 48MB of RAM.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group