NASLite Network Attached Storage

www.serverelements.com
Task-specific simplicity with low hardware requirements.
It is currently Mon Dec 06, 2021 6:21 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 13 posts ] 
Author Message
PostPosted: Fri Aug 26, 2005 7:52 pm 
Offline

Joined: Mon Aug 22, 2005 10:29 am
Posts: 10
I have 3 80 Gb hard drives attached to the motherboard. When I boot hda and hdb are recognized just fine but when I try to confiigure the drives on hdb... it says the drive does not exist... if I switch the cables it still only recognizes the drives on hda.....

Anyone know how I can fix this??

Thanks...


Top
 Profile  
 
 Post subject:
PostPosted: Sun Aug 28, 2005 5:24 am 
Offline

Joined: Sun Feb 27, 2005 11:08 am
Posts: 225
are you sure the second controller is not just broken.

If this were me i would boot with Knoppix and have a play there.

Knoppix has alot more tools at your disposal to test whats happening


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 29, 2005 8:55 am 
Offline

Joined: Mon Aug 22, 2005 10:29 am
Posts: 10
I dont think its the controller because I have tried it on 2 different pcs. Both are Dell Gxi and have the most recent bios. Do you need to use newer drives for NAS to work?


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 29, 2005 12:57 pm 
Can you supply the model number and make of the Drive.

i have tested nas on some old drives smallest was 2 gb 2x 4gb and they worked correctly.

if the drive is old i'd suggest buying a new one. as these are cheap and you will have much more space.

if you run a winme startup disk does fdisk see all the drives? i assume the bios sees the drives, do you have the jumper setting as master on the disk?

not sure about this but maybe if the drive is set as a slave you are pressing the wrong button to configure the drive in naslite?

can you post a log.


Top
  
 
 Post subject:
PostPosted: Tue Aug 30, 2005 8:35 am 
Offline

Joined: Mon Aug 22, 2005 10:29 am
Posts: 10
They are all 80 Gb Western Digital Drives... I will post the model #'s when I get home. The bios recognizes all of them. The disks jumpers settings are set to cable select... I am pressing the correct buttons


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 30, 2005 10:24 am 
on the second ide channel make sure that the HD is on the last IDE connector, the one at the end.

IF they are all the same model then i see no reason as to why Naslite would have a problem as it all ready sees the HD on the primary channel.

have you tried putting the HD that does not show up on the primary ide channel.

here is how I would find out what going on.

First I'd have both HD's on the primary ide. i'd have one set as master and the other as slave, then on the third i'd also have this set as master.

then id boot the pc and check that the HD show up in post.

then id configure each drive 1 2 3.

if drive 3 still does not show id take it and replace with the master on ide 1 reboot and then see if i can configure it. if it still does not show then id admit defeat. and think the drive was faulty.

Cable Select. The drive is configured at the factory for a cable select setting. This allows the drive to assume the proper role of master or slave based on the connector used on the cable. For the cable select setting to work properly, the cables you are using must support the cable select feature. Current UltraATA cables with the 3 colored connectors do support this feature.


Cable Select

A feature of some PCs that allows IDE/ATA hard disks to be numerically identified by the order in which they are attached to the cable. Both the BIOS and the drive must support this feature. Without Cable Select, jumpers on the IDE drive must be set to Master or Slave designations


your problem could be the postition of where the HD is on the cable.
if the drive is a slave on the 2ide and you are pressing 3 to configure the drive then its the wrong one, you would have to press 4.


Top
  
 
 Post subject:
PostPosted: Tue Aug 30, 2005 8:57 pm 
Offline
Site Admin

Joined: Tue Jul 13, 2004 4:11 pm
Posts: 1771
Location: Server Elements
I assume that you are using a Gbit version. If so, then make sure that you are using the latest version. There was a problem with the autoconfigurator that has been corrected since.


Top
 Profile  
 
 Post subject:
PostPosted: Wed Aug 31, 2005 8:19 am 
Offline

Joined: Mon Aug 22, 2005 10:29 am
Posts: 10
Ive tried all of the things you guys have described and have resolved to the fact that its only going to allow me to have 2 hard drives configured on the first IDE. I even tried two completely different hard drives and cables on two different boxes.. both pc's are Dell Gxi 5166Ms. BTW.. I am using the regular SMB naslite diskette...

Well, 2 drives for NAS is better than none.

If anyone else has better luck with this particular pc please let me know....


Top
 Profile  
 
 Post subject:
PostPosted: Sun Dec 04, 2005 12:38 pm 
Offline

Joined: Sun Dec 04, 2005 12:32 pm
Posts: 2
I'm having the exact same problem. Was a solution ever found?

I've had a 30GB and 200GB on te 1st IDE channel for over 3 months with no problems. I just bought 120GB and put it as master on the 2nd Channel. I get the same error that says the drive must be a fixed sidk and not CD-ROM ect...

This is how disk-3 shows up in the system page



Disk-3 Initialization Messages

1. Checking for Disk-3
2. Disk-3 is not available

Disk-3 Hardware

* ST3120022A, ATA DISK drive
* attached ide-disk driver.
* host protected area => 1
* 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63, UDMA(33)

NOTE: Disk-3 is installed and can be configured for use with NASLite-SMBG.



It says it is installed and recognized, but I still get the error.

The jumper is set to master and the cable is correct.

I am using NASLite-SMBG ( v1.4 )

What can I do to resolve this?

Here is the sys log from my last boot up:

Server System Log

* Dec 4 00:12:06 GigaServer syslog.info syslogd started: BusyBox v1.00-pre10 (2004.06.01-20:52+0000)
* Dec 4 00:12:06 GigaServer daemon.info init: Starting pid 288, console /dev/null: '/sbin/klogd'
* Dec 4 00:12:06 GigaServer syslog.notice klogd: klogd started: BusyBox v1.00-pre10 (2004.06.01-20:52+0000)
* Dec 4 00:12:06 GigaServer user.warn klogd: Linux version 2.4.26.NASLite (root@ServerElements.com) (gcc version 3.3.2) #23 Tue Oct 5 11:47:14 MDT 2004
* Dec 4 00:12:06 GigaServer user.info klogd: BIOS-provided physical RAM map:
* Dec 4 00:12:06 GigaServer user.warn klogd: BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
* Dec 4 00:12:06 GigaServer user.warn klogd: BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
* Dec 4 00:12:06 GigaServer user.warn klogd: BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
* Dec 4 00:12:06 GigaServer user.warn klogd: BIOS-e820: 0000000000100000 - 000000000a000000 (usable)
* Dec 4 00:12:06 GigaServer user.warn klogd: BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
* Dec 4 00:12:06 GigaServer user.notice klogd: 160MB LOWMEM available.
* Dec 4 00:12:06 GigaServer user.warn klogd: On node 0 totalpages: 40960
* Dec 4 00:12:06 GigaServer user.warn klogd: zone(0): 4096 pages.
* Dec 4 00:12:06 GigaServer user.warn klogd: zone(1): 36864 pages.
* Dec 4 00:12:06 GigaServer user.warn klogd: zone(2): 0 pages.
* Dec 4 00:12:06 GigaServer user.warn klogd: Kernel command line:
* Dec 4 00:12:06 GigaServer user.info klogd: Initializing CPU#0
* Dec 4 00:12:06 GigaServer user.warn klogd: Detected 266.617 MHz processor.
* Dec 4 00:12:06 GigaServer user.warn klogd: Console: colour VGA+ 80x25
* Dec 4 00:12:06 GigaServer user.warn klogd: Calibrating delay loop... 530.84 BogoMIPS
* Dec 4 00:12:06 GigaServer user.info klogd: Memory: 159832k/163840k available (1085k kernel code, 3620k reserved, 230k data, 336k init, 0k highmem)
* Dec 4 00:12:06 GigaServer user.info klogd: Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
* Dec 4 00:12:06 GigaServer user.info klogd: Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
* Dec 4 00:12:06 GigaServer user.info klogd: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
* Dec 4 00:12:06 GigaServer user.info klogd: Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
* Dec 4 00:12:06 GigaServer user.warn klogd: Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
* Dec 4 00:12:06 GigaServer user.info klogd: CPU: L1 I cache: 16K, L1 D cache: 16K
* Dec 4 00:12:06 GigaServer user.info klogd: CPU: L2 cache: 512K
* Dec 4 00:12:06 GigaServer user.debug klogd: CPU: After generic, caps: 0080f9ff 00000000 00000000 00000000
* Dec 4 00:12:06 GigaServer user.debug klogd: CPU: Common caps: 0080f9ff 00000000 00000000 00000000
* Dec 4 00:12:06 GigaServer user.warn klogd: CPU: Intel Pentium II (Klamath) stepping 04
* Dec 4 00:12:06 GigaServer user.info klogd: Checking 'hlt' instruction... OK.
* Dec 4 00:12:06 GigaServer user.info klogd: Checking for popad bug... OK.
* Dec 4 00:12:06 GigaServer user.warn klogd: POSIX conformance testing by UNIFIX
* Dec 4 00:12:06 GigaServer user.info klogd: PCI: PCI BIOS revision 2.10 entry at 0xfd9b3, last bus=1
* Dec 4 00:12:06 GigaServer user.info klogd: PCI: Using configuration type 1
* Dec 4 00:12:06 GigaServer user.info klogd: PCI: Probing PCI hardware
* Dec 4 00:12:06 GigaServer user.warn klogd: PCI: Probing PCI hardware (bus 00)
* Dec 4 00:12:06 GigaServer user.info klogd: PCI: Using IRQ router PIIX/ICH [8086/7110] at 00:07.0
* Dec 4 00:12:06 GigaServer user.info klogd: Limiting direct PCI/PCI transfers.
* Dec 4 00:12:06 GigaServer user.info klogd: Linux NET4.0 for Linux 2.4
* Dec 4 00:12:06 GigaServer user.info klogd: Based upon Swansea University Computer Society NET3.039
* Dec 4 00:12:06 GigaServer user.warn klogd: Initializing RT netlink socket
* Dec 4 00:12:06 GigaServer user.warn klogd: Starting kswapd
* Dec 4 00:12:06 GigaServer user.info klogd: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
* Dec 4 00:12:06 GigaServer user.info klogd: devfs: boot_options: 0x1
* Dec 4 00:12:06 GigaServer user.warn klogd: pty: 256 Unix98 ptys configured
* Dec 4 00:12:06 GigaServer user.info klogd: Real Time Clock Driver v1.10f
* Dec 4 00:12:06 GigaServer user.info klogd: Floppy drive(s): fd0 is 1.44M
* Dec 4 00:12:06 GigaServer user.info klogd: FDC 0 is a National Semiconductor PC87306
* Dec 4 00:12:06 GigaServer user.warn klogd: RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
* Dec 4 00:12:06 GigaServer user.info klogd: loop: loaded (max 8 devices)
* Dec 4 00:12:06 GigaServer user.info klogd: Intel(R) PRO/1000 Network Driver - version 5.2.30.1-k1
* Dec 4 00:12:06 GigaServer user.info klogd: Copyright (c) 1999-2004 Intel Corporation.
* Dec 4 00:12:06 GigaServer user.info klogd: ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
* Dec 4 00:12:06 GigaServer user.warn klogd: sk98lin: No adapter found.
* Dec 4 00:12:06 GigaServer user.info klogd: r8169 Gigabit Ethernet driver 1.2 loaded
* Dec 4 00:12:06 GigaServer user.info klogd: PCI: Found IRQ 10 for device 00:0f.0
* Dec 4 00:12:06 GigaServer user.debug klogd: r8169: PCI device 00:0f.0: unknown chip version, assuming RTL-8169
* Dec 4 00:12:06 GigaServer user.debug klogd: r8169: PCI device 00:0f.0: TxConfig = 0x4000000
* Dec 4 00:12:06 GigaServer user.debug klogd: eth0: Identified chip type is 'RTL-8169'.
* Dec 4 00:12:06 GigaServer user.info klogd: eth0: RealTek RTL8169 Gigabit Ethernet at 0xca800000, 00:0f:b5:85:4c:e6, IRQ 10
* Dec 4 00:12:06 GigaServer user.info klogd: eth0: Auto-negotiation Enabled.
* Dec 4 00:12:06 GigaServer user.info klogd: eth0: 1000Mbps Full-duplex operation.
* Dec 4 00:12:06 GigaServer user.info klogd: Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
* Dec 4 00:12:06 GigaServer user.info klogd: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
* Dec 4 00:12:06 GigaServer user.info klogd: PIIX4: IDE controller at PCI slot 00:07.1
* Dec 4 00:12:06 GigaServer user.info klogd: PIIX4: chipset revision 1
* Dec 4 00:12:06 GigaServer user.info klogd: PIIX4: not 100% native mode: will probe irqs later
* Dec 4 00:12:06 GigaServer user.info klogd: ide0: BM-DMA at 0x1420-0x1427, BIOS settings: hda:pio, hdb:DMA
* Dec 4 00:12:06 GigaServer user.info klogd: ide1: BM-DMA at 0x1428-0x142f, BIOS settings: hdc:DMA, hdd:pio
* Dec 4 00:12:06 GigaServer user.warn klogd: hda: IBM-DTLA-307030, ATA DISK drive
* Dec 4 00:12:06 GigaServer user.warn klogd: hdb: Maxtor 6Y200P0, ATA DISK drive
* Dec 4 00:12:06 GigaServer user.warn klogd: blk: queue c02c4420, I/O limit 4095Mb (mask 0xffffffff)
* Dec 4 00:12:06 GigaServer user.warn klogd: blk: queue c02c455c, I/O limit 4095Mb (mask 0xffffffff)
* Dec 4 00:12:06 GigaServer user.warn klogd: hdc: ST3120022A, ATA DISK drive
* Dec 4 00:12:06 GigaServer user.warn klogd: blk: queue c02c4874, I/O limit 4095Mb (mask 0xffffffff)
* Dec 4 00:12:06 GigaServer user.warn klogd: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
* Dec 4 00:12:06 GigaServer user.warn klogd: ide1 at 0x170-0x177,0x376 on irq 15
* Dec 4 00:12:06 GigaServer user.warn klogd: hda: attached ide-disk driver.
* Dec 4 00:12:06 GigaServer user.warn klogd: hda: host protected area => 1
* Dec 4 00:12:06 GigaServer user.info klogd: hda: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=3737/255/63, UDMA(33)
* Dec 4 00:12:06 GigaServer user.warn klogd: hdb: attached ide-disk driver.
* Dec 4 00:12:06 GigaServer user.warn klogd: hdb: host protected area => 1
* Dec 4 00:12:06 GigaServer user.info klogd: hdb: 398297088 sectors (203928 MB) w/7936KiB Cache, CHS=24792/255/63, UDMA(33)
* Dec 4 00:12:06 GigaServer user.warn klogd: hdc: attached ide-disk driver.
* Dec 4 00:12:06 GigaServer user.warn klogd: hdc: host protected area => 1
* Dec 4 00:12:06 GigaServer user.info klogd: 33)
* Dec 4 00:12:06 GigaServer user.info klogd: Partition check:
* Dec 4 00:12:06 GigaServer user.info klogd: /dev/ide/host0/bus0/target0/lun0: p1
* Dec 4 00:12:06 GigaServer user.info klogd: /dev/ide/host0/bus0/target1/lun0: p1
* Dec 4 00:12:06 GigaServer user.info klogd: /dev/ide/host0/bus1/target0/lun0: unknown partition table
* Dec 4 00:12:06 GigaServer user.info klogd: NET4: Linux TCP/IP 1.0 for NET4.0
* Dec 4 00:12:06 GigaServer user.info klogd: IP Protocols: ICMP, UDP, TCP
* Dec 4 00:12:06 GigaServer user.info klogd: IP: routing cache hash table of 1024 buckets, 8Kbytes
* Dec 4 00:12:06 GigaServer user.info klogd: TCP: Hash tables configured (established 16384 bind 32768)
* Dec 4 00:12:06 GigaServer user.info klogd: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
* Dec 4 00:12:06 GigaServer user.notice klogd: RAMDISK: Compressed image found at block 798
* Dec 4 00:12:06 GigaServer user.warn klogd: EXT2-fs warning: checktime reached, running e2fsck is recommended
* Dec 4 00:12:06 GigaServer user.warn klogd: VFS: Mounted root (ext2 filesystem).
* Dec 4 00:12:06 GigaServer user.info klogd: Mounted devfs on /dev
* Dec 4 00:12:06 GigaServer user.info klogd: Freeing unused kernel memory: 336k freed
* Dec 4 00:13:22 GigaServer auth.info login[289]: root login on `pts/0'


Top
 Profile  
 
 Post subject:
PostPosted: Sun Dec 04, 2005 1:44 pm 
Hi,

What happens if you remove the two drives on the Primary IDe Channel and replace with the drive you are having problems with, Can you configure the drive?

Eden


Top
  
 
 Post subject:
PostPosted: Mon Dec 05, 2005 11:19 pm 
Offline

Joined: Sun Dec 04, 2005 12:32 pm
Posts: 2
edeng wrote:
Hi,

What happens if you remove the two drives on the Primary IDe Channel and replace with the drive you are having problems with, Can you configure the drive?

Eden


No good. I put the drive as the master on IDE1. Same error message. The system see the drive, NASLite just won't configure it.

Does anything need to be done to the drive before hand? I didn't think I did anything special to the other 2 drives?


Top
 Profile  
 
 Post subject:
PostPosted: Tue Dec 06, 2005 2:33 am 
Offline

Joined: Sat Nov 19, 2005 6:39 pm
Posts: 633
Location: California
In the log TEKNOSYS shows, the key line giving a hint at the possible problem is:

/dev/ide/host0/bus1/target0/lun0: unknown partition table

I believe that somehow a partition was created and NASLite does not recognize it, even though the "configure" should be able to wipe the hard disk.

Try software that came with the HDD to initialize it again (low-level format); no need to low-level format the entire disk, most vendors have a "quick format" choice. The important part is to get first few cylinders wiped out, destroying any partition table on the drive. There's also some free software out there that will do the trick (http://www.killdisk.com/downloadfree.htm). (You can abort after writing about 2-3% of the drive.)

Hope this helps ...


Top
 Profile  
 
 Post subject:
PostPosted: Sat Jan 14, 2006 9:14 pm 
Offline

Joined: Sat Jan 14, 2006 8:23 pm
Posts: 1
Hi, Just wondering if there is resolution to this problem.

I am trying my hands on NASLite (non-G version) and running into exactly the same problem of cannot format / use disk(s) on the second IDE controller. Any pointer / help is appreciated.

Here is what I have tried and observed:

(a). two disks (120MB & 1.6G) with a P-100 board. The board has 2 IDE controllers. If both disks are connected to primary IDE controller, everything works. I have both disks formated while they are on the primary IDE controller.
(b). If either disk is connected to the second IDE controller, NASLite boot process recognizes it, but it does not get mounted at the end of the boot process and system says there is no disk if I try to format it again. I have tried both disks and master / slave permutations.
(c). I have tried to boot up the hardware with Damn Small Linux (2.4.31 kernel) with one disk each on primary and secondary controllers. I can use both disks and move files back and forth. This proves that both IDE controllers are working. Afterwards I move all disks to primary IDE and boot up NASLite, all files are on right disks and I can access all of them. However if I move either disk to secondary IDE, it is not accessible through NASLite anymore.
(d). This problem is observed in both -SMB and -NFX versions. I have not tested in -FTP version.

Here is a boot log:

Jan 14 19:04:18 NASLite syslog.info syslogd started: BusyBox v1.00-pre10 (2004.06.01-20:52+0000)
Jan 14 19:04:18 NASLite daemon.info init: Starting pid 253, console /dev/null: '/sbin/klogd'
Jan 14 19:04:18 NASLite syslog.notice klogd: klogd started: BusyBox v1.00-pre10 (2004.06.01-20:52+0000)
Jan 14 19:04:18 NASLite user.warn klogd: Linux version 2.4.26.NASLite (root@(none)) (gcc version 3.3.2) #10 Mon Jun 14 14:07:53 MDT 2004
Jan 14 19:04:18 NASLite user.info klogd: BIOS-provided physical RAM map:
Jan 14 19:04:18 NASLite user.warn klogd: BIOS-88: 0000000000000000 - 000000000009f000 (usable)
Jan 14 19:04:18 NASLite user.warn klogd: BIOS-88: 0000000000100000 - 0000000001800000 (usable)
Jan 14 19:04:18 NASLite user.notice klogd: 24MB LOWMEM available.
Jan 14 19:04:18 NASLite user.warn klogd: On node 0 totalpages: 6144
Jan 14 19:04:18 NASLite user.warn klogd: zone(0): 4096 pages.
Jan 14 19:04:18 NASLite user.warn klogd: zone(1): 2048 pages.
Jan 14 19:04:18 NASLite user.warn klogd: zone(2): 0 pages.
Jan 14 19:04:18 NASLite user.info klogd: DMI not present.
Jan 14 19:04:18 NASLite user.warn klogd: Kernel command line:
Jan 14 19:04:18 NASLite user.info klogd: Initializing CPU#0
Jan 14 19:04:18 NASLite user.warn klogd: Detected 99.027 MHz processor.
Jan 14 19:04:18 NASLite user.warn klogd: Console: colour VGA+ 80x25
Jan 14 19:04:18 NASLite user.warn klogd: Calibrating delay loop... 197.42 BogoMIPS
Jan 14 19:04:18 NASLite user.info klogd: Memory: 22164k/24576k available (1044k kernel code, 2024k reserved, 281k data, 232k init, 0k highmem)
Jan 14 19:04:18 NASLite user.info klogd: Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Jan 14 19:04:18 NASLite user.info klogd: Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Jan 14 19:04:18 NASLite user.info klogd: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Jan 14 19:04:18 NASLite user.info klogd: Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 14 19:04:18 NASLite user.warn klogd: Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan 14 19:04:18 NASLite user.notice klogd: Intel Pentium with F0 0F bug - workaround enabled.
Jan 14 19:04:18 NASLite user.debug klogd: CPU: After generic, caps: 000001bf 00000000 00000000 00000000
Jan 14 19:04:18 NASLite user.debug klogd: CPU: Common caps: 000001bf 00000000 00000000 00000000
Jan 14 19:04:18 NASLite user.warn klogd: CPU: Intel Pentium 75 - 200 stepping 05
Jan 14 19:04:18 NASLite user.info klogd: Checking 'hlt' instruction... OK.
Jan 14 19:04:18 NASLite user.info klogd: Checking for popad bug... OK.
Jan 14 19:04:18 NASLite user.warn klogd: POSIX conformance testing by UNIFIX
Jan 14 19:04:18 NASLite user.info klogd: PCI: PCI BIOS revision 2.00 entry at 0xfc8e0, last bus=0
Jan 14 19:04:18 NASLite user.info klogd: PCI: Using configuration type 2
Jan 14 19:04:18 NASLite user.info klogd: PCI: Probing PCI hardware
Jan 14 19:04:18 NASLite user.warn klogd: PCI: Probing PCI hardware (bus 00)
Jan 14 19:04:18 NASLite user.info klogd: Linux NET4.0 for Linux 2.4
Jan 14 19:04:18 NASLite user.info klogd: Based upon Swansea University Computer Society NET3.039
Jan 14 19:04:18 NASLite user.warn klogd: Initializing RT netlink socket
Jan 14 19:04:18 NASLite user.warn klogd: Starting kswapd
Jan 14 19:04:18 NASLite user.info klogd: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
Jan 14 19:04:18 NASLite user.info klogd: devfs: boot_options: 0x1
Jan 14 19:04:18 NASLite user.warn klogd: pty: 256 Unix98 ptys configured
Jan 14 19:04:18 NASLite user.info klogd: Real Time Clock Driver v1.10f
Jan 14 19:04:18 NASLite user.info klogd: Floppy drive(s): fd0 is 1.44M
Jan 14 19:04:18 NASLite user.info klogd: FDC 0 is a National Semiconductor PC87306
Jan 14 19:04:18 NASLite user.warn klogd: RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Jan 14 19:04:18 NASLite user.info klogd: loop: loaded (max 8 devices)
Jan 14 19:04:18 NASLite user.info klogd: dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15
Jan 14 19:04:18 NASLite user.warn klogd: FW Version=$Version$
Jan 14 19:04:18 NASLite user.info klogd: ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
Jan 14 19:04:18 NASLite user.info klogd: http://www.scyld.com/network/ne2k-pci.html
Jan 14 19:04:18 NASLite user.warn klogd: eth0: Winbond 89C940 found at 0x6000, IRQ 11, 00:20:78:19:44:66.
Jan 14 19:04:18 NASLite user.info klogd: pcnet32.c:v1.28 02.20.2004 tsbogend@alpha.franken.de
Jan 14 19:04:18 NASLite user.info klogd: ThunderLAN driver v1.15
Jan 14 19:04:18 NASLite user.info klogd: TLAN: 0 devices installed, PCI: 0 EISA: 0
Jan 14 19:04:18 NASLite user.info klogd: dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
Jan 14 19:04:18 NASLite user.info klogd: forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.25.
Jan 14 19:04:18 NASLite user.info klogd: Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
Jan 14 19:04:18 NASLite user.info klogd: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Jan 14 19:04:18 NASLite user.info klogd: VIA_IDE: IDE controller at PCI slot 00:07.0
Jan 14 19:04:18 NASLite user.info klogd: VIA_IDE: chipset revision 0
Jan 14 19:04:18 NASLite user.info klogd: VIA_IDE: not 100% native mode: will probe irqs later
Jan 14 19:04:18 NASLite user.warn klogd: hda: Maxtor 71626 AP, ATA DISK drive
Jan 14 19:04:18 NASLite user.warn klogd: hdc: Maxtor 7120 AT, ATA DISK drive
Jan 14 19:04:18 NASLite user.warn klogd: hdd: HP CD-Writer+ 7200, ATAPI CD/DVD-ROM drive
Jan 14 19:04:18 NASLite user.warn klogd: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Jan 14 19:04:18 NASLite user.warn klogd: ide1 at 0x170-0x177,0x376 on irq 15
Jan 14 19:04:18 NASLite user.warn klogd: hda: attached ide-disk driver.
Jan 14 19:04:18 NASLite user.warn klogd: hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
Jan 14 19:04:18 NASLite user.warn klogd: hda: task_no_data_intr: error=0x04 { DriveStatusError }
Jan 14 19:04:18 NASLite user.info klogd: hda: 3184170 sectors (1630 MB) w/128KiB Cache, CHS=789/64/63
Jan 14 19:04:18 NASLite user.warn klogd: hdc: attached ide-disk driver.
Jan 14 19:04:18 NASLite user.warn klogd: hdc: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
Jan 14 19:04:18 NASLite user.warn klogd: hdc: task_no_data_intr: error=0x04 { DriveStatusError }
Jan 14 19:04:18 NASLite user.info klogd: hdc: 254592 sectors (130 MB) w/64KiB Cache, CHS=936/16/17
Jan 14 19:04:18 NASLite user.info klogd: Partition check:
Jan 14 19:04:18 NASLite user.info klogd: /dev/ide/host0/bus0/target0/lun0: p1
Jan 14 19:04:18 NASLite user.info klogd: /dev/ide/host0/bus1/target0/lun0: p1
Jan 14 19:04:18 NASLite user.info klogd: NET4: Linux TCP/IP 1.0 for NET4.0
Jan 14 19:04:18 NASLite user.info klogd: IP Protocols: ICMP, UDP, TCP
Jan 14 19:04:18 NASLite user.info klogd: IP: routing cache hash table of 512 buckets, 4Kbytes
Jan 14 19:04:18 NASLite user.info klogd: TCP: Hash tables configured (established 2048 bind 4096)
Jan 14 19:04:18 NASLite user.info klogd: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Jan 14 19:04:18 NASLite user.notice klogd: RAMDISK: Compressed image found at block 803
Jan 14 19:04:18 NASLite user.warn klogd: VFS: Mounted root (ext2 filesystem).
Jan 14 19:04:18 NASLite user.info klogd: Mounted devfs on /dev
Jan 14 19:04:18 NASLite user.info klogd: Freeing unused kernel memory: 232k freed


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 13 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group